boards/st/stm32l1_disco/stm32l1_disco.dts

/*
 * Copyright (c) 2019 eTactica ehf
 *
 * SPDX-License-Identifier: Apache-2.0
 */

/dts-v1/;
#include <st/l1/stm32l151Xb.dtsi>
#include <st/l1/stm32l152r(6-8-b)tx-pinctrl.dtsi>
#include <zephyr/dt-bindings/input/input-event-codes.h>

/ {
	model = "STMicroelectronics STM32L1DISCOVERY board";
	compatible = "st,stm32l1discovery";

	chosen {
		zephyr,console = &usart1;
		zephyr,shell-uart = &usart1;
		zephyr,sram = &sram0;
		zephyr,flash = &flash0;
	};

	leds {
		compatible = "gpio-leds";
		green_led: ld3 {
			gpios = <&gpiob 7 GPIO_ACTIVE_HIGH>;
			label = "User LD3";
		};
		blue_led: ld4 {
			gpios = <&gpiob 6 GPIO_ACTIVE_HIGH>;
			label = "User LD4";
		};
	};

	gpio_keys {
		compatible = "gpio-keys";
		user_button: button {
			label = "User";
			gpios = <&gpioa 0 GPIO_ACTIVE_LOW>;
			zephyr,code = <INPUT_KEY_0>;
		};
	};

	aliases {
		led0 = &green_led;
		led1 = &blue_led;
		sw0 = &user_button;
		eeprom-0 = &eeprom;
		watchdog0 = &iwdg;
	};
};

&clk_lsi {
	status = "okay";
};

&clk_hsi {
	status = "okay";
};

&pll {
	div = <4>;
	mul = <8>;
	/* out of the box, MCO from stlink is not enabled, unlike later discos */
	clocks = <&clk_hsi>;
	status = "okay";
};

&rcc {
	clocks = <&pll>;
	clock-frequency = <DT_FREQ_M(32)>;
	ahb-prescaler = <1>;
	apb1-prescaler = <1>;
	apb2-prescaler = <1>;
};

&usart1 {
	pinctrl-0 = <&usart1_tx_pa9 &usart1_rx_pa10>;
	pinctrl-names = "default";
	current-speed = <115200>;
	status = "okay";
};

&usart2 {
	pinctrl-0 = <&usart2_tx_pa2 &usart2_rx_pa3>;
	pinctrl-names = "default";
	current-speed = <115200>;
	status = "okay";
};

&usart3 {
	pinctrl-0 = <&usart3_tx_pb10 &usart3_rx_pb11>;
	pinctrl-names = "default";
	current-speed = <115200>;
	status = "okay";
};

&i2c1 {
	pinctrl-0 = <&i2c1_scl_pb6 &i2c1_sda_pb7>;
	pinctrl-names = "default";
	status = "okay";
	clock-frequency = <I2C_BITRATE_FAST>;
};

&i2c2 {
	pinctrl-0 = <&i2c2_scl_pb10 &i2c2_sda_pb11>;
	pinctrl-names = "default";
	status = "okay";
	clock-frequency = <I2C_BITRATE_FAST>;
};

&spi1 {
	pinctrl-0 = <&spi1_nss_pa4 &spi1_sck_pa5
		     &spi1_miso_pa6 &spi1_mosi_pa7>;
	pinctrl-names = "default";
	status = "okay";
};

&spi2 {
	pinctrl-0 = <&spi2_nss_pb12 &spi2_sck_pb13
		     &spi2_miso_pb14 &spi2_mosi_pb15>;
	pinctrl-names = "default";
	status = "okay";
};

&rtc {
	clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>,
		 <&rcc STM32_SRC_LSI RTC_SEL(2)>;
	status = "okay";

	backup_regs {
		status = "okay";
	};
};

&eeprom {
		status = "okay";
};

&iwdg {
		status = "okay";
};