| /* |
| * Copyright (c) 2020, Seagate Technology LLC |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #ifndef ZEPHYR_DRIVERS_SERIAL_UART_LPC11U6X_H_ |
| #define ZEPHYR_DRIVERS_SERIAL_UART_LPC11U6X_H_ |
| |
| #include <zephyr/drivers/pinctrl.h> |
| |
| #define LPC11U6X_UART0_CLK 14745600 |
| |
| #define LPC11U6X_UART0_LCR_WLS_5BITS 0 |
| #define LPC11U6X_UART0_LCR_WLS_6BITS 1 |
| #define LPC11U6X_UART0_LCR_WLS_7BITS 2 |
| #define LPC11U6X_UART0_LCR_WLS_8BITS 3 |
| #define LPC11U6X_UART0_LCR_STOP_1BIT (0 << 2) |
| #define LPC11U6X_UART0_LCR_STOP_2BIT (1 << 2) |
| #define LPC11U6X_UART0_LCR_PARTIY_ENABLE (1 << 3) |
| #define LPC11U6X_UART0_LCR_PARTIY_ODD (0 << 4) |
| #define LPC11U6X_UART0_LCR_PARTIY_EVEN (1 << 4) |
| |
| #define LPC11U6X_UART0_LCR_DLAB (1 << 7) |
| |
| #define LPC11U6X_UART0_FCR_FIFO_EN (1 << 0) |
| |
| #define LPC11U6X_UART0_LSR_RDR (1 << 0) |
| #define LPC11U6X_UART0_LSR_OE (1 << 1) |
| #define LPC11U6X_UART0_LSR_PE (1 << 2) |
| #define LPC11U6X_UART0_LSR_FE (1 << 3) |
| #define LPC11U6X_UART0_LSR_BI (1 << 4) |
| #define LPC11U6X_UART0_LSR_THRE (1 << 5) |
| #define LPC11U6X_UART0_LSR_TEMT (1 << 6) |
| #define LPC11U6X_UART0_LSR_RXFE (1 << 7) |
| |
| #define LPC11U6X_UART0_IER_RBRINTEN (1 << 0) |
| #define LPC11U6X_UART0_IER_THREINTEN (1 << 1) |
| #define LPC11U6X_UART0_IER_RLSINTEN (1 << 2) |
| #define LPC11U6X_UART0_IER_MASK (0x30F) |
| |
| #define LPC11U6X_UART0_IIR_STATUS (0x1 << 0) |
| #define LPC11U6X_UART0_IIR_INTID(x) (((x) >> 1) & 0x7) |
| #define LPC11U6X_UART0_IIR_INTID_RLS 0x3 |
| #define LPC11U6X_UART0_IIR_INTID_RDA 0x2 |
| #define LPC11U6X_UART0_IIR_INTID_CTI 0x6 |
| #define LPC11U6X_UART0_IIR_INTID_THRE 0x1 |
| |
| #define LPC11U6X_UART0_FIFO_SIZE 16 |
| |
| #define LPC11U6X_UARTX_CFG_ENABLE (0x1 << 0) |
| #define LPC11U6X_UARTX_CFG_DATALEN_7BIT (0x0 << 2) |
| #define LPC11U6X_UARTX_CFG_DATALEN_8BIT (0x1 << 2) |
| #define LPC11U6X_UARTX_CFG_DATALEN_9BIT (0x2 << 2) |
| #define LPC11U6X_UARTX_CFG_PARITY_NONE (0x0 << 4) |
| #define LPC11U6X_UARTX_CFG_PARITY_EVEN (0x2 << 4) |
| #define LPC11U6X_UARTX_CFG_PARITY_ODD (0x3 << 4) |
| #define LPC11U6X_UARTX_CFG_STOP_1BIT (0x0 << 6) |
| #define LPC11U6X_UARTX_CFG_STOP_2BIT (0x1 << 6) |
| |
| #define LPC11U6X_UARTX_CFG_MASK (0x00FCDAFD) |
| |
| #define LPC11U6X_UARTX_STAT_RXRDY (1 << 0) |
| #define LPC11U6X_UARTX_STAT_TXRDY (1 << 2) |
| #define LPC11U6X_UARTX_STAT_TXIDLE (1 << 3) |
| #define LPC11U6X_UARTX_STAT_OVERRUNINT (1 << 8) |
| #define LPC11U6X_UARTX_STAT_FRAMERRINT (1 << 13) |
| #define LPC11U6X_UARTX_STAT_PARITYERRINT (1 << 14) |
| |
| #define LPC11U6X_UARTX_BRG_MASK (0xFFFF) |
| |
| #define LPC11U6X_UARTX_INT_EN_SET_RXRDYEN (1 << 0) |
| #define LPC11U6X_UARTX_INT_EN_SET_TXRDYEN (1 << 2) |
| #define LPC11U6X_UARTX_INT_EN_SET_OVERRUNEN (1 << 8) |
| #define LPC11U6X_UARTX_INT_EN_SET_FRAMERREN (1 << 13) |
| #define LPC11U6X_UARTX_INT_EN_SET_PARITYERREN (1 << 14) |
| #define LPC11U6X_UARTX_INT_EN_SET_MASK (0x0001F96D) |
| |
| #define LPC11U6X_UARTX_INT_EN_CLR_RXRDYCLR (1 << 0) |
| #define LPC11U6X_UARTX_INT_EN_CLR_TXRDYCLR (1 << 2) |
| #define LPC11U6X_UARTX_INT_EN_CLR_OVERRUNCLR (1 << 8) |
| #define LPC11U6X_UARTX_INT_EN_CLR_FRAMERRCLR (1 << 13) |
| #define LPC11U6X_UARTX_INT_EN_CLR_PARITYERRCLR (1 << 14) |
| |
| #define LPC11U6X_UARTX_INT_STAT_RXRDY (1 << 0) |
| #define LPC11U6X_UARTX_INT_STAT_TXRDY (1 << 2) |
| #define LPC11U6X_UARTX_INT_STAT_OVERRUN (1 << 8) |
| #define LPC11U6X_UARTX_INT_STAT_FRAMERR (1 << 13) |
| #define LPC11U6X_UARTX_INT_STAT_PARITYERR (1 << 14) |
| |
| #define LPC11U6X_UARTX_DEVICE_PER_IRQ 2 |
| |
| struct lpc11u6x_uart0_regs { |
| union { |
| volatile const uint32_t rbr; /* RX buffer (RO) */ |
| volatile uint32_t thr; /* TX buffer (WO) */ |
| volatile uint32_t dll; /* Divisor latch LSB */ |
| }; |
| union { |
| volatile uint32_t dlm; /* Divisor latch MSB */ |
| volatile uint32_t ier; /* Interrupt enable */ |
| }; |
| union { |
| volatile uint32_t iir; /* Interrupt ID */ |
| volatile uint32_t fcr; /* FIFO Control */ |
| }; |
| volatile uint32_t lcr; /* Line Control */ |
| volatile uint32_t mcr; /* Modem Control */ |
| volatile uint32_t lsr; /* Line Status */ |
| volatile uint32_t msr; /* Modem Status */ |
| volatile uint32_t scr; /* Scratch pad */ |
| volatile uint32_t acr; /* Auto-baud Control */ |
| volatile uint32_t icr; /* IrDA Control */ |
| volatile uint32_t fdr; /* Fractional Divider */ |
| volatile uint32_t osr; /* Oversampling register */ |
| volatile uint32_t ter; /* Transmit enable */ |
| volatile uint32_t reserved1[3]; |
| volatile uint32_t hden; /* Half duplex */ |
| volatile uint32_t reserved2; |
| volatile uint32_t sci_ctrl; /* Smart card interface */ |
| volatile uint32_t rs485_ctrl; /* RS-485 control */ |
| volatile uint32_t rs485_addr_match; /* RS-485 address match */ |
| volatile uint32_t rs485_dly; /* RS-485 delay direction control |
| * delay |
| */ |
| volatile uint32_t sync_ctrl; /* Synchronous mode control */ |
| }; |
| |
| struct lpc11u6x_uart0_config { |
| struct lpc11u6x_uart0_regs *uart0; |
| const struct device *clock_dev; |
| uint32_t baudrate; |
| uint32_t clkid; |
| const struct pinctrl_dev_config *pincfg; |
| #ifdef CONFIG_UART_INTERRUPT_DRIVEN |
| void (*irq_config_func)(const struct device *dev); |
| #endif /* CONFIG_UART_INTERRUPT_DRIVEN */ |
| }; |
| |
| struct lpc11u6x_uart0_data { |
| uint32_t baudrate; |
| uint8_t parity; |
| uint8_t stop_bits; |
| uint8_t data_bits; |
| uint8_t flow_ctrl; |
| #ifdef CONFIG_UART_INTERRUPT_DRIVEN |
| uart_irq_callback_user_data_t cb; |
| void *cb_data; |
| uint32_t cached_iir; |
| #endif /* CONFIG_UART_INTERRUPT_DRIVEN */ |
| }; |
| |
| struct lpc11u6x_uartx_regs { |
| volatile uint32_t cfg; /* Configuration register */ |
| volatile uint32_t ctl; /* Control register */ |
| volatile uint32_t stat; /* Status register */ |
| volatile uint32_t int_en_set; /* Interrupt enable and set */ |
| volatile uint32_t int_en_clr; /* Interrupt enable clear */ |
| volatile const uint32_t rx_dat; /* Receiver data */ |
| volatile const uint32_t rx_dat_stat; /* Receiver data status */ |
| volatile uint32_t tx_dat; /* Transmit data */ |
| volatile uint32_t brg; /* Baud rate generator */ |
| volatile const uint32_t int_stat; /* Interrupt status */ |
| volatile uint32_t osr; /* Oversample selection */ |
| volatile uint32_t addr; /* Address register*/ |
| }; |
| |
| struct lpc11u6x_uartx_config { |
| struct lpc11u6x_uartx_regs *base; |
| const struct device *clock_dev; |
| uint32_t baudrate; |
| uint32_t clkid; |
| const struct pinctrl_dev_config *pincfg; |
| }; |
| |
| struct lpc11u6x_uartx_data { |
| uint32_t baudrate; |
| uint8_t parity; |
| uint8_t stop_bits; |
| uint8_t data_bits; |
| uint8_t flow_ctrl; |
| #ifdef CONFIG_UART_INTERRUPT_DRIVEN |
| uart_irq_callback_user_data_t cb; |
| void *cb_data; |
| #endif /* CONFIG_UART_INTERRUPT_DRIVEN */ |
| }; |
| |
| /* Since UART1 and UART4 share the same IRQ (as well as UART2 and UART3), |
| * we need to give the ISR a way to know all the devices that should be |
| * notified when said IRQ is raised |
| */ |
| struct lpc11u6x_uartx_shared_irq { |
| const struct device *devices[LPC11U6X_UARTX_DEVICE_PER_IRQ]; |
| }; |
| |
| #if CONFIG_UART_INTERRUPT_DRIVEN && \ |
| (DT_NODE_HAS_STATUS(DT_NODELABEL(uart1), okay) || \ |
| DT_NODE_HAS_STATUS(DT_NODELABEL(uart4), okay)) |
| static void lpc11u6x_uartx_isr_config_1(const struct device *dev); |
| #endif /* CONFIG_UART_INTERRUPT_DRIVEN && |
| * (DT_NODE_HAS_STATUS(DT_NODELABEL(uart2), okay) || |
| * DT_NODE_HAS_STATUS(DT_NODELABEL(uart3), okay)) |
| */ |
| |
| #if CONFIG_UART_INTERRUPT_DRIVEN && \ |
| (DT_NODE_HAS_STATUS(DT_NODELABEL(uart2), okay) || \ |
| DT_NODE_HAS_STATUS(DT_NODELABEL(uart3), okay)) |
| static void lpc11u6x_uartx_isr_config_2(const struct device *dev); |
| #endif /* CONFIG_UART_INTERRUPT_DRIVEN && |
| * (DT_NODE_HAS_STATUS(DT_NODELABEL(uart2), okay) || |
| * DT_NODE_HAS_STATUS(DT_NODELABEL(uart3), okay)) |
| */ |
| #endif /* ZEPHYR_DRIVERS_SERIAL_UART_LPC11U6X_H_ */ |
