boards/arm/frdm_k22f/doc/index.rst - third_party/github/zephyrproject-rtos/zephyr - Git at Google

 .. _frdm_k22f:

 NXP FRDM-K22F
 ##############

 Overview
 ********

 The Freedom-K22F is an ultra-low-cost development platform for Kinetis K22
 MCUs.

 - Form-factor compatible with the Arduino R3 pin layout
 - Peripherals enable rapid prototyping, including a 6-axis digital
   accelerometer and magnetometer to create full eCompass capabilities, a
   tri-colored LED and 2 user push-buttons for direct interaction, a optional
   microSD card slot, and headers for use with Bluetooth* and 2.4 GHz radio
   add-on modules
 - OpenSDAv2, the NXP open source hardware embedded serial and debug adapter
   running an open source bootloader, offers options for serial communication,
   flash programming, and run-control debugging

 .. image:: frdm_k22f.jpg
    :align: center
    :alt: FRDM-K22F

 Hardware
 ********

 - MK22FN512VLH12 (120 MHz, 1 MB flash memory, 256 KB RAM, low-power,
   crystal-less USB, and 64 pin Low profile Quad Flat Package (LQFP))
 - Dual role USB interface with micro-B USB connector
 - RGB LED
 - FXOS8700CQ accelerometer and magnetometer
 - Two user push buttons
 - Flexible power supply option - OpenSDAv2 USB, Kinetis K22 USB, and external source
 - Easy access to MCU input/output through Arduino* R3 compatible I/O connectors
 - Programmable OpenSDAv2 debug circuit supporting the CMSIS-DAP Interface
   software that provides:

   - Mass storage device (MSD) flash programming interface
   - CMSIS-DAP debug interface over a driver-less USB HID connection providing
     run-control debugging and compatibility with IDE tools
   - Virtual serial port interface
   - Open source CMSIS-DAP software project

 - Optional SDHC

 For more information about the K22F SoC and FRDM-K22F board:

 - `K22F Website`_
 - `K22F Datasheet`_
 - `K22F Reference Manual`_
 - `FRDM-K22F Website`_
 - `FRDM-K22F User Guide`_
 - `FRDM-K22F Schematics`_

 Supported Features
 ==================

 The frdm_k22f board configuration supports the hardware features listed
 below.  For additional features not yet supported, please also refer to the
 :ref:`frdm_k64f`, which is the superset board in NXP's Kinetis K series.
 NXP prioritizes enabling the superset board with NXP's Full Platform Support for
 Zephyr.  Therefore, the frdm_k64f board may have additional features
 already supported, which can also be re-used on this frdm_k22f board:

 +-----------+------------+-------------------------------------+
 | Interface | Controller | Driver/Component                    |
 +===========+============+=====================================+
 | NVIC      | on-chip    | nested vector interrupt controller  |
 +-----------+------------+-------------------------------------+
 | SYSTICK   | on-chip    | systick                             |
 +-----------+------------+-------------------------------------+
 | PINMUX    | on-chip    | pinmux                              |
 +-----------+------------+-------------------------------------+
 | GPIO      | on-chip    | gpio                                |
 +-----------+------------+-------------------------------------+
 | I2C       | on-chip    | i2c                                 |
 +-----------+------------+-------------------------------------+
 | SPI       | on-chip    | spi                                 |
 +-----------+------------+-------------------------------------+
 | WATCHDOG  | on-chip    | watchdog                            |
 +-----------+------------+-------------------------------------+
 | ADC       | on-chip    | adc                                 |
 +-----------+------------+-------------------------------------+
 | PWM       | on-chip    | pwm                                 |
 +-----------+------------+-------------------------------------+
 | UART      | on-chip    | serial port-polling;                |
 |           |            | serial port-interrupt               |
 +-----------+------------+-------------------------------------+
 | FLASH     | on-chip    | soc flash                           |
 +-----------+------------+-------------------------------------+
 | USB       | on-chip    | USB device                          |
 +-----------+------------+-------------------------------------+
 | SENSOR    | off-chip   | fxos8700 polling;                   |
 |           |            | fxos8700 trigger                    |
 +-----------+------------+-------------------------------------+
 | RNGA      | on-chip    | entropy;                            |
 |           |            | random                              |
 +-----------+------------+-------------------------------------+
 | FTFE      | on-chip    | flash programming                   |
 +-----------+------------+-------------------------------------+

 The default configuration can be found in the defconfig file:

 :zephyr_file:`boards/arm/frdm_k22f/frdm_k22f_defconfig`

 Other hardware features are not currently supported by the port.

 Connections and IOs
 ===================

 The K22F SoC has five pairs of pinmux/gpio controllers.

 +-------+-----------------+---------------------------+
 | Name  | Function        | Usage                     |
 +=======+=================+===========================+
 | PTA1  | GPIO            | Red LED                   |
 +-------+-----------------+---------------------------+
 | PTA2  | GPIO            | Green LED                 |
 +-------+-----------------+---------------------------+
 | PTD5  | GPIO            | Blue LED                  |
 +-------+-----------------+---------------------------+
 | PTC1  | GPIO            | SW2                       |
 +-------+-----------------+---------------------------+
 | PTD0  | GPIO            | FXOS8700 INT1             |
 +-------+-----------------+---------------------------+
 | PTD1  | GPIO            | FXOS8700 INT2             |
 +-------+-----------------+---------------------------+
 | PTB17 | GPIO            | SW3                       |
 +-------+-----------------+---------------------------+
 | PTE1  | UART1_RX        | UART Console              |
 +-------+-----------------+---------------------------+
 | PTE0  | UART1_TX        | UART Console              |
 +-------+-----------------+---------------------------+
 | PTD2  | UART2_RX        | UART BT HCI               |
 +-------+-----------------+---------------------------+
 | PTD3  | UART2_TX        | UART BT HCI               |
 +-------+-----------------+---------------------------+
 | PTC4  | SPI0_PCS0       | SPI                       |
 +-------+-----------------+---------------------------+
 | PTD1  | SPI0_SCK        | SPI                       |
 +-------+-----------------+---------------------------+
 | PTD2  | SPI0_SOUT       | SPI                       |
 +-------+-----------------+---------------------------+
 | PTD3  | SPI0_SIN        | SPI                       |
 +-------+-----------------+---------------------------+
 | PTB2  | I2C0_SCL        | I2C / FXOS8700            |
 +-------+-----------------+---------------------------+
 | PTB3  | I2C0_SDA        | I2C / FXOS8700            |
 +-------+-----------------+---------------------------+

 System Clock
 ============

 The K22F SoC is configured to use the 8 MHz crystal oscillator on the board
 with the on-chip PLL to generate a 72 MHz system clock in its RUN mode. This
 clock was selected to allow for the maximum number of peripherals to be used
 with the crystal and PLL clocks. Other clock configurations are possible
 through NXP SDK currently.

 Serial Port
 ===========

 The K22F SoC has three UARTs. One is configured for the console, another for BT
 HCI, and the remaining are not used.

 USB
 ===

 The K22F SoC has a USB OTG (USBOTG) controller that supports both
 device and host functions through its micro USB connector (K22F USB).
 Only USB device function is supported in Zephyr at the moment.

 Programming and Debugging
 *************************

 Build and flash applications as usual (see :ref:`build_an_application` and
 :ref:`application_run` for more details).

 Configuring a Debug Probe
 =========================

 A debug probe is used for both flashing and debugging the board. This board is
 configured by default to use the :ref:`opensda-daplink-onboard-debug-probe`.

 Early versions of this board have an outdated version of the OpenSDA bootloader
 and require an update. Please see the `DAPLink Bootloader Update`_ page for
 instructions to update from the CMSIS-DAP bootloader to the DAPLink bootloader.

 Option 1: :ref:`opensda-daplink-onboard-debug-probe` (Recommended)
 ------------------------------------------------------------------

 Install the :ref:`pyocd-debug-host-tools` and make sure they are in your search
 path.

 Follow the instructions in :ref:`opensda-daplink-onboard-debug-probe` to program
 the `OpenSDA DAPLink FRDM-K22F Firmware`_.

 Option 2: :ref:`opensda-jlink-onboard-debug-probe`
 --------------------------------------------------

 Install the :ref:`jlink-debug-host-tools` and make sure they are in your search
 path.

 Follow the instructions in :ref:`opensda-jlink-onboard-debug-probe` to program
 the `Segger J-Link OpenSDA V2.1 Firmware`_. Note that Segger
 does provide an OpenSDA J-Link Board-Specific Firmware for this board, however
 it is not compatible with the DAPLink bootloader.

 Add the arguments ``-DBOARD_FLASH_RUNNER=jlink`` and
 ``-DBOARD_DEBUG_RUNNER=jlink`` when you invoke ``west build`` to override the
 default runner from pyOCD to J-Link:

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: frdm_k22f
    :gen-args: -DBOARD_FLASH_RUNNER=jlink -DBOARD_DEBUG_RUNNER=jlink
    :goals: build

 Configuring a Console
 =====================

 Regardless of your choice in debug probe, we will use the OpenSDA
 microcontroller as a usb-to-serial adapter for the serial console.

 Connect a USB cable from your PC to J26.

 Use the following settings with your serial terminal of choice (minicom, putty,
 etc.):

 - Speed: 115200
 - Data: 8 bits
 - Parity: None
 - Stop bits: 1

 Flashing
 ========

 Here is an example for the :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: frdm_k22f
    :goals: flash

 Open a serial terminal, reset the board (press the SW1 button), and you should
 see the following message in the terminal:

 .. code-block:: console

    ***** Booting Zephyr OS v2.0.0 *****
    Hello World! frdm_k22f

 Debugging
 =========

 Here is an example for the :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: frdm_k22f
    :goals: debug

 Open a serial terminal, step through the application in your debugger, and you
 should see the following message in the terminal:

 .. code-block:: console

    ***** Booting Zephyr OS v2.0.0 *****
    Hello World! frdm_k22f

 .. _FRDM-K22F Website:
    https://www.nxp.com/support/developer-resources/evaluation-and-development-boards/freedom-development-boards/mcu-boards/nxp-freedom-development-platform-for-kinetis-k22-mcus:FRDM-K22F

 .. _FRDM-K22F User Guide:
    https://www.nxp.com/webapp/Download?colCode=FRDMK22FUG

 .. _FRDM-K22F Schematics:
    https://www.nxp.com/webapp/Download?colCode=FRDM-K22F-SCH

 .. _K22F Website:
    https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/kinetis-cortex-m-mcus/k-seriesperformancem4/k2x-usb/kinetis-k22-120-mhz-cost-effective-full-speed-usb-microcontrollers-mcus-based-on-arm-cortex-m4-core:K22_120

 .. _K22F Datasheet:
    https://www.nxp.com/docs/en/data-sheet/K22P121M120SF7.pdf

 .. _K22F Reference Manual:
    https://www.nxp.com/docs/en/reference-manual/K22P121M120SF7RM.pdf

 .. _OpenSDA DAPLink FRDM-K22F Firmware:
    http://www.nxp.com/assets/downloads/data/en/ide-debug-compile-build-tools/OpenSDAv2.2_DAPLink_frdmk22f_rev0242.zip

 .. _DAPLink Bootloader Update:
    https://os.mbed.com/blog/entry/DAPLink-bootloader-update/

 .. _Segger J-Link OpenSDA V2.1 Firmware:
    https://www.segger.com/downloads/jlink/OpenSDA_V2_1.bin
	.. _frdm_k22f:

	NXP FRDM-K22F
	##############

	Overview
	********

	The Freedom-K22F is an ultra-low-cost development platform for Kinetis K22
	MCUs.

	- Form-factor compatible with the Arduino R3 pin layout
	- Peripherals enable rapid prototyping, including a 6-axis digital
	accelerometer and magnetometer to create full eCompass capabilities, a
	tri-colored LED and 2 user push-buttons for direct interaction, a optional
	microSD card slot, and headers for use with Bluetooth* and 2.4 GHz radio
	add-on modules
	- OpenSDAv2, the NXP open source hardware embedded serial and debug adapter
	running an open source bootloader, offers options for serial communication,
	flash programming, and run-control debugging

	.. image:: frdm_k22f.jpg
	:align: center
	:alt: FRDM-K22F

	Hardware
	********

	- MK22FN512VLH12 (120 MHz, 1 MB flash memory, 256 KB RAM, low-power,
	crystal-less USB, and 64 pin Low profile Quad Flat Package (LQFP))
	- Dual role USB interface with micro-B USB connector
	- RGB LED
	- FXOS8700CQ accelerometer and magnetometer
	- Two user push buttons
	- Flexible power supply option - OpenSDAv2 USB, Kinetis K22 USB, and external source
	- Easy access to MCU input/output through Arduino* R3 compatible I/O connectors
	- Programmable OpenSDAv2 debug circuit supporting the CMSIS-DAP Interface
	software that provides:

	- Mass storage device (MSD) flash programming interface
	- CMSIS-DAP debug interface over a driver-less USB HID connection providing
	run-control debugging and compatibility with IDE tools
	- Virtual serial port interface
	- Open source CMSIS-DAP software project

	- Optional SDHC

	For more information about the K22F SoC and FRDM-K22F board:

	- `K22F Website`_
	- `K22F Datasheet`_
	- `K22F Reference Manual`_
	- `FRDM-K22F Website`_
	- `FRDM-K22F User Guide`_
	- `FRDM-K22F Schematics`_

	Supported Features
	==================

	The frdm_k22f board configuration supports the hardware features listed
	below. For additional features not yet supported, please also refer to the
	:ref:`frdm_k64f`, which is the superset board in NXP's Kinetis K series.
	NXP prioritizes enabling the superset board with NXP's Full Platform Support for
	Zephyr. Therefore, the frdm_k64f board may have additional features
	already supported, which can also be re-used on this frdm_k22f board:

	+-----------+------------+-------------------------------------+
	\| Interface \| Controller \| Driver/Component \|
	+===========+============+=====================================+
	\| NVIC \| on-chip \| nested vector interrupt controller \|
	+-----------+------------+-------------------------------------+
	\| SYSTICK \| on-chip \| systick \|
	+-----------+------------+-------------------------------------+
	\| PINMUX \| on-chip \| pinmux \|
	+-----------+------------+-------------------------------------+
	\| GPIO \| on-chip \| gpio \|
	+-----------+------------+-------------------------------------+
	\| I2C \| on-chip \| i2c \|
	+-----------+------------+-------------------------------------+
	\| SPI \| on-chip \| spi \|
	+-----------+------------+-------------------------------------+
	\| WATCHDOG \| on-chip \| watchdog \|
	+-----------+------------+-------------------------------------+
	\| ADC \| on-chip \| adc \|
	+-----------+------------+-------------------------------------+
	\| PWM \| on-chip \| pwm \|
	+-----------+------------+-------------------------------------+
	\| UART \| on-chip \| serial port-polling; \|
	\| \| \| serial port-interrupt \|
	+-----------+------------+-------------------------------------+
	\| FLASH \| on-chip \| soc flash \|
	+-----------+------------+-------------------------------------+
	\| USB \| on-chip \| USB device \|
	+-----------+------------+-------------------------------------+
	\| SENSOR \| off-chip \| fxos8700 polling; \|
	\| \| \| fxos8700 trigger \|
	+-----------+------------+-------------------------------------+
	\| RNGA \| on-chip \| entropy; \|
	\| \| \| random \|
	+-----------+------------+-------------------------------------+
	\| FTFE \| on-chip \| flash programming \|
	+-----------+------------+-------------------------------------+

	The default configuration can be found in the defconfig file:

	:zephyr_file:`boards/arm/frdm_k22f/frdm_k22f_defconfig`

	Other hardware features are not currently supported by the port.

	Connections and IOs
	===================

	The K22F SoC has five pairs of pinmux/gpio controllers.

	+-------+-----------------+---------------------------+
	\| Name \| Function \| Usage \|
	+=======+=================+===========================+
	\| PTA1 \| GPIO \| Red LED \|
	+-------+-----------------+---------------------------+
	\| PTA2 \| GPIO \| Green LED \|
	+-------+-----------------+---------------------------+
	\| PTD5 \| GPIO \| Blue LED \|
	+-------+-----------------+---------------------------+
	\| PTC1 \| GPIO \| SW2 \|
	+-------+-----------------+---------------------------+
	\| PTD0 \| GPIO \| FXOS8700 INT1 \|
	+-------+-----------------+---------------------------+
	\| PTD1 \| GPIO \| FXOS8700 INT2 \|
	+-------+-----------------+---------------------------+
	\| PTB17 \| GPIO \| SW3 \|
	+-------+-----------------+---------------------------+
	\| PTE1 \| UART1_RX \| UART Console \|
	+-------+-----------------+---------------------------+
	\| PTE0 \| UART1_TX \| UART Console \|
	+-------+-----------------+---------------------------+
	\| PTD2 \| UART2_RX \| UART BT HCI \|
	+-------+-----------------+---------------------------+
	\| PTD3 \| UART2_TX \| UART BT HCI \|
	+-------+-----------------+---------------------------+
	\| PTC4 \| SPI0_PCS0 \| SPI \|
	+-------+-----------------+---------------------------+
	\| PTD1 \| SPI0_SCK \| SPI \|
	+-------+-----------------+---------------------------+
	\| PTD2 \| SPI0_SOUT \| SPI \|
	+-------+-----------------+---------------------------+
	\| PTD3 \| SPI0_SIN \| SPI \|
	+-------+-----------------+---------------------------+
	\| PTB2 \| I2C0_SCL \| I2C / FXOS8700 \|
	+-------+-----------------+---------------------------+
	\| PTB3 \| I2C0_SDA \| I2C / FXOS8700 \|
	+-------+-----------------+---------------------------+

	System Clock
	============

	The K22F SoC is configured to use the 8 MHz crystal oscillator on the board
	with the on-chip PLL to generate a 72 MHz system clock in its RUN mode. This
	clock was selected to allow for the maximum number of peripherals to be used
	with the crystal and PLL clocks. Other clock configurations are possible
	through NXP SDK currently.

	Serial Port
	===========

	The K22F SoC has three UARTs. One is configured for the console, another for BT
	HCI, and the remaining are not used.

	USB
	===

	The K22F SoC has a USB OTG (USBOTG) controller that supports both
	device and host functions through its micro USB connector (K22F USB).
	Only USB device function is supported in Zephyr at the moment.

	Programming and Debugging
	*************************

	Build and flash applications as usual (see :ref:`build_an_application` and
	:ref:`application_run` for more details).

	Configuring a Debug Probe
	=========================

	A debug probe is used for both flashing and debugging the board. This board is
	configured by default to use the :ref:`opensda-daplink-onboard-debug-probe`.

	Early versions of this board have an outdated version of the OpenSDA bootloader
	and require an update. Please see the `DAPLink Bootloader Update`_ page for
	instructions to update from the CMSIS-DAP bootloader to the DAPLink bootloader.

	Option 1: :ref:`opensda-daplink-onboard-debug-probe` (Recommended)
	------------------------------------------------------------------

	Install the :ref:`pyocd-debug-host-tools` and make sure they are in your search
	path.

	Follow the instructions in :ref:`opensda-daplink-onboard-debug-probe` to program
	the `OpenSDA DAPLink FRDM-K22F Firmware`_.

	Option 2: :ref:`opensda-jlink-onboard-debug-probe`
	--------------------------------------------------

	Install the :ref:`jlink-debug-host-tools` and make sure they are in your search
	path.

	Follow the instructions in :ref:`opensda-jlink-onboard-debug-probe` to program
	the `Segger J-Link OpenSDA V2.1 Firmware`_. Note that Segger
	does provide an OpenSDA J-Link Board-Specific Firmware for this board, however
	it is not compatible with the DAPLink bootloader.

	Add the arguments ``-DBOARD_FLASH_RUNNER=jlink`` and
	``-DBOARD_DEBUG_RUNNER=jlink`` when you invoke ``west build`` to override the
	default runner from pyOCD to J-Link:

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: frdm_k22f
	:gen-args: -DBOARD_FLASH_RUNNER=jlink -DBOARD_DEBUG_RUNNER=jlink
	:goals: build

	Configuring a Console
	=====================

	Regardless of your choice in debug probe, we will use the OpenSDA
	microcontroller as a usb-to-serial adapter for the serial console.

	Connect a USB cable from your PC to J26.

	Use the following settings with your serial terminal of choice (minicom, putty,
	etc.):

	- Speed: 115200
	- Data: 8 bits
	- Parity: None
	- Stop bits: 1

	Flashing
	========

	Here is an example for the :ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: frdm_k22f
	:goals: flash

	Open a serial terminal, reset the board (press the SW1 button), and you should
	see the following message in the terminal:

	.. code-block:: console

	*** Booting Zephyr OS v2.0.0 ***
	Hello World! frdm_k22f

	Debugging
	=========

	Here is an example for the :ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: frdm_k22f
	:goals: debug

	Open a serial terminal, step through the application in your debugger, and you
	should see the following message in the terminal:

	.. code-block:: console

	*** Booting Zephyr OS v2.0.0 ***
	Hello World! frdm_k22f

	.. _FRDM-K22F Website:
	https://www.nxp.com/support/developer-resources/evaluation-and-development-boards/freedom-development-boards/mcu-boards/nxp-freedom-development-platform-for-kinetis-k22-mcus:FRDM-K22F

	.. _FRDM-K22F User Guide:
	https://www.nxp.com/webapp/Download?colCode=FRDMK22FUG

	.. _FRDM-K22F Schematics:
	https://www.nxp.com/webapp/Download?colCode=FRDM-K22F-SCH

	.. _K22F Website:
	https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/kinetis-cortex-m-mcus/k-seriesperformancem4/k2x-usb/kinetis-k22-120-mhz-cost-effective-full-speed-usb-microcontrollers-mcus-based-on-arm-cortex-m4-core:K22_120

	.. _K22F Datasheet:
	https://www.nxp.com/docs/en/data-sheet/K22P121M120SF7.pdf

	.. _K22F Reference Manual:
	https://www.nxp.com/docs/en/reference-manual/K22P121M120SF7RM.pdf

	.. _OpenSDA DAPLink FRDM-K22F Firmware:
	http://www.nxp.com/assets/downloads/data/en/ide-debug-compile-build-tools/OpenSDAv2.2_DAPLink_frdmk22f_rev0242.zip

	.. _DAPLink Bootloader Update:
	https://os.mbed.com/blog/entry/DAPLink-bootloader-update/

	.. _Segger J-Link OpenSDA V2.1 Firmware:
	https://www.segger.com/downloads/jlink/OpenSDA_V2_1.bin