| # Kconfig - Synopsys DesignWare Ethernet driver configuration options |
| |
| # |
| # Copyright (c) 2015 Intel Corporation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| config SYS_LOG_ETHERNET_LEVEL |
| int |
| prompt "Ethernet driver log level" |
| depends on SYS_LOG && ETHERNET |
| default 0 |
| range 0 4 |
| help |
| Sets log level for Ethernet Device Drivers. |
| Levels are: |
| 0 OFF, do not write |
| 1 ERROR, only write SYS_LOG_ERR |
| 2 WARNING, write SYS_LOG_WRN in adition to previous level |
| 3 INFO, write SYS_LOG_INF in adition to previous levels |
| 4 DEBUG, write SYS_LOG_DBG in adition to previous levels |
| |
| menuconfig ETH_DW |
| bool |
| prompt "Synopsys DesignWare Ethernet driver" |
| depends on ETHERNET |
| default n |
| help |
| Enable Synopsys DesignWare Ethernet driver. |
| |
| if ETH_DW |
| config ETH_DW_SHARED_IRQ |
| bool |
| default n |
| |
| config ETH_DW_0 |
| bool "Synopsys DesignWare Ethernet port 0" |
| default n |
| help |
| Include port 0 driver |
| |
| config ETH_DW_0_NAME |
| string "Driver name" |
| depends on ETH_DW_0 |
| default "ETH_0" |
| |
| choice |
| prompt "Port 0 Interrupts via" |
| default ETH_DW_0_IRQ_SHARED |
| depends on ETH_DW_0 |
| |
| config ETH_DW_0_IRQ_DIRECT |
| bool "Direct Hardware Interrupt" |
| help |
| When interrupts fire, the driver's ISR function is being called directly. |
| |
| config ETH_DW_0_IRQ_SHARED |
| bool "Shared IRQ" |
| depends on SHARED_IRQ |
| select ETH_DW_SHARED_IRQ |
| help |
| When interrupts fire, the shared IRQ driver is notified. Then the shared IRQ |
| driver dispatches the interrupt to other drivers. |
| |
| endchoice |
| |
| config ETH_DW_0_IRQ_SHARED_NAME |
| string "Device name for Shared IRQ" |
| depends on ETH_DW_0 && ETH_DW_0_IRQ_SHARED |
| help |
| Specify the device name for the shared IRQ driver. It is used to register |
| this driver with the shared IRQ driver, so interrupts can be dispatched |
| correctly. |
| |
| config ETH_DW_0_IRQ_PRI |
| int "Controller interrupt priority" |
| depends on ETH_DW_0 && ETH_DW_0_IRQ_DIRECT |
| default 0 |
| help |
| IRQ priority |
| |
| endif # ETH_DW |
| |
| source "drivers/ethernet/Kconfig.enc28j60" |
| source "drivers/ethernet/Kconfig.ksdk" |
