| # Kconfig.k64 - K64_FTM PWM configuration options |
| # |
| # |
| # Copyright (c) 2016 Intel Corporation |
| # Copyright (c) 2016 Wind River Systems, Inc. |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| ################################################ |
| # K64 Flex Timer Module (FTM) |
| ################################################ |
| |
| menuconfig PWM_K64_FTM |
| bool "PWM with Freescale K64 Flex Timer Module (FTM)" |
| depends on PWM && SOC_MK64F12 |
| default n |
| help |
| Enable Pulse Width Modulation driver for Freescale |
| K64 Flex Timer Module (FTM). |
| |
| if PWM_K64_FTM |
| |
| config SYS_LOG_PWM_K64_FTM_LEVEL |
| int |
| prompt "Sets log level for pwm_ftm driver" |
| depends on PWM_K64_FTM |
| default 0 |
| help |
| Sets log level for pwm_ftm driver. |
| |
| Levels are: |
| |
| - 0 OFF, do not write |
| |
| - 1 ERROR, only write SYS_LOG_ERR |
| |
| - 2 WARNING, write SYS_LOG_WRN in adition to previous level |
| |
| - 3 INFO, write SYS_LOG_INF in adition to previous levels |
| |
| - 4 DEBUG, write SYS_LOG_DBG in adition to previous levels |
| |
| #### FTM0 ##### |
| |
| config PWM_K64_FTM_0 |
| bool "K64 FTM PWM Module 0" |
| depends on PWM_K64_FTM |
| default n |
| help |
| Enable config PWM options for FTM0 source module. |
| |
| config PWM_K64_FTM_0_DEV_NAME |
| string "K64 FTM PWM Module 0 Device Name" |
| depends on PWM_K64_FTM_0 |
| default "PWM_0" |
| help |
| Specify the device name for the FTM0 source module. |
| |
| config PWM_K64_FTM_0_PRESCALE |
| int "K64 FTM0 prescale value" |
| default 1 |
| depends on PWM_K64_FTM_0 |
| help |
| Specify the FTM timer prescale value. The valid values are |
| 1, 2, 4, 8, 16, 32, 64, or 128. |
| |
| config PWM_K64_FTM_0_PERIOD |
| int "K64 FTM0 period value" |
| default 65535 |
| depends on PWM_K64_FTM_0 |
| help |
| Specify the FTM0 PWM period in ticks |
| |
| menu "K64 FTM0 Clock Source" |
| depends on PWM_K64_FTM_0 |
| |
| choice PWM_K64_FTM_0_CLOCK_SOURCE_CHOICE |
| prompt "Choose the K64 FTM0 clock source" |
| default PWM_K64_FTM_0_CLOCK_SOURCE_SYSTEM |
| |
| config PWM_K64_FTM_0_CLOCK_SOURCE_NONE |
| bool "No clock selected (FTM counter disable)" |
| |
| config PWM_K64_FTM_0_CLOCK_SOURCE_SYSTEM |
| bool "System clock" |
| |
| config PWM_K64_FTM_0_CLOCK_SOURCE_FIXED |
| bool "Fixed Frequency Clock" |
| |
| config PWM_K64_FTM_0_CLOCK_SOURCE_EXTERNAL |
| bool "External Clock" |
| |
| config PWM_K64_FTM_0_CLOCK_SOURCE_QUAD |
| bool "Quadrature Decoder" |
| |
| endchoice |
| |
| endmenu |
| |
| config PWM_K64_FTM_0_CLOCK_SOURCE |
| int |
| # Omit prompt to signify "hidden" option |
| depends on PWM_K64_FTM_0 |
| default 0 if PWM_K64_FTM_0_CLOCK_SOURCE_NONE |
| default 1 if PWM_K64_FTM_0_CLOCK_SOURCE_SYSTEM |
| default 2 if PWM_K64_FTM_0_CLOCK_SOURCE_FIXED |
| default 3 if PWM_K64_FTM_0_CLOCK_SOURCE_EXTERNAL |
| default 4 if PWM_K64_FTM_0_CLOCK_SOURCE_QUAD |
| help |
| Specify K64 FTM0 clock source |
| |
| config PWM_K64_FTM_0_PHASE_ENABLE_0 |
| bool "FTM0 Enable Phase for channel 0" |
| depends on PWM_K64_FTM_0 |
| default n |
| help |
| Allow a phase offset on FTM0 channel 0. This configures |
| channels 0 and 1 to be in combine mode therefore |
| channel 1 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_K64_FTM_0_PHASE_ENABLE_2 |
| bool "FTM0 Enable Phase for channel 2" |
| depends on PWM_K64_FTM_0 |
| default n |
| help |
| Allow a phase offset on FTM0 channel 2. This configures |
| channels 2 and 3 to be in combine mode therefore |
| channel 3 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_K64_FTM_0_PHASE_ENABLE_4 |
| bool "FTM0 Enable Phase for channel 4" |
| depends on PWM_K64_FTM_0 |
| default n |
| help |
| Allow a phase offset on FTM0 channel 4. This configures |
| channels 4 and 5 to be in combine mode therefore |
| channel 5 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_K64_FTM_0_PHASE_ENABLE_6 |
| bool "FTM0 Enable Phase for channel 6" |
| depends on PWM_K64_FTM_0 |
| default n |
| help |
| Allow a phase offset on FTM0 channel 6. This configures |
| channels 6 and 7 to be in combine mode therefore |
| channel 7 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| #### FTM1 ##### |
| |
| config PWM_K64_FTM_1 |
| bool "K64 FTM PWM Module 1" |
| depends on PWM_K64_FTM |
| default n |
| help |
| Enable config PWM options for FTM1 source module. |
| |
| config PWM_K64_FTM_1_DEV_NAME |
| string "K64 FTM PWM Module 1 Device Name" |
| depends on PWM_K64_FTM_1 |
| default "PWM_1" |
| help |
| Specify the device name for the FTM1 source module. |
| |
| config PWM_K64_FTM_1_PRESCALE |
| int "FTM1 prescale value" |
| default 1 |
| depends on PWM_K64_FTM_1 |
| help |
| Specify the FTM1 timer prescale value. The valid values are |
| 1, 2, 4, 8, 16, 32, 64, or 128 |
| |
| config PWM_K64_FTM_1_PERIOD |
| int "FTM1 period value" |
| default 65535 |
| depends on PWM_K64_FTM_1 |
| help |
| Specify the FTM1 PWM period in ticks |
| |
| menu "K64 FTM1 Clock Source" |
| depends on PWM_K64_FTM_1 |
| |
| choice PWM_K64_FTM_1_CLOCK_SOURCE_CHOICE |
| prompt "Choose the FTM1 clock source" |
| default PWM_K64_FTM_1_CLOCK_SOURCE_SYSTEM |
| |
| config PWM_K64_FTM_1_CLOCK_SOURCE_NONE |
| bool "No clock selected (FTM counter disable)" |
| |
| config PWM_K64_FTM_1_CLOCK_SOURCE_SYSTEM |
| bool "System clock" |
| |
| config PWM_K64_FTM_1_CLOCK_SOURCE_FIXED |
| bool "Fixed Frequency Clock" |
| |
| config PWM_K64_FTM_1_CLOCK_SOURCE_EXTERNAL |
| bool "External Clock" |
| |
| config PWM_K64_FTM_1_CLOCK_SOURCE_QUAD |
| bool "Quadrature Decoder" |
| |
| endchoice |
| |
| endmenu |
| |
| config PWM_K64_FTM_1_CLOCK_SOURCE |
| int |
| # Omit prompt to signify "hidden" option |
| depends on PWM_K64_FTM_1 |
| default 0 if PWM_K64_FTM_1_CLOCK_SOURCE_NONE |
| default 1 if PWM_K64_FTM_1_CLOCK_SOURCE_SYSTEM |
| default 2 if PWM_K64_FTM_1_CLOCK_SOURCE_FIXED |
| default 3 if PWM_K64_FTM_1_CLOCK_SOURCE_EXTERNAL |
| default 4 if PWM_K64_FTM_1_CLOCK_SOURCE_QUAD |
| help |
| Specify K64 FTM1 clock source |
| |
| config PWM_K64_FTM_1_PHASE_ENABLE_0 |
| bool "FTM1 Enable Phase for channel 0" |
| depends on PWM_K64_FTM_1 |
| default n |
| help |
| Allow a phase offset on FTM1 channel 0. This configures |
| channels 0 and 1 to be in combine mode therefore |
| channel 1 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_FTM_1_PHASE_ENABLE_2 |
| bool "FTM1 Enable Phase for channel 2" |
| depends on PWM_K64_FTM_1 |
| default n |
| help |
| Allow a phase offset on FTM1 channel 2. This configures |
| channels 2 and 3 to be in combine mode therefore |
| channel 3 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_FTM_1_PHASE_ENABLE_4 |
| bool "FTM1 Enable Phase for channel 4" |
| depends on PWM_K64_FTM_1 |
| default n |
| help |
| Allow a phase offset on FTM1 channel 4. This configures |
| channels 4 and 5 to be in combine mode therefore |
| channel 5 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_FTM_1_PHASE_ENABLE_6 |
| bool "FTM1 Enable Phase for channel 6" |
| depends on PWM_K64_FTM_1 |
| default n |
| help |
| Allow a phase offset on FTM1 channel 6. This configures |
| channels 6 and 7 to be in combine mode therefore |
| channel 7 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| #### FTM2 ##### |
| |
| config PWM_K64_FTM_2 |
| bool "K64 FTM PWM Module 2" |
| depends on PWM_K64_FTM |
| default n |
| help |
| Enable config PWM options for FTM2 source module. |
| |
| config PWM_K64_FTM_2_DEV_NAME |
| string "K64 FTM PWM Module 2 Device Name" |
| depends on PWM_K64_FTM_2 |
| default "PWM_2" |
| help |
| Specify the device name for the FTM2 source module. |
| |
| config PWM_K64_FTM_2_PRESCALE |
| int "FTM2 prescale value" |
| default 1 |
| depends on PWM_K64_FTM_2 |
| help |
| Specify the FTM2 timer prescale value. The valid values are |
| 1, 2, 4, 8, 16, 32, 64, or 128 |
| |
| config PWM_K64_FTM_2_PERIOD |
| int "FTM2 period value" |
| default 65535 |
| depends on PWM_K64_FTM_2 |
| help |
| Specify the FTM2 PWM period in ticks |
| |
| menu "K64 FTM2 Clock Source" |
| depends on PWM_K64_FTM_2 |
| |
| choice PWM_K64_FTM_2_CLOCK_SOURCE_CHOICE |
| prompt "Choose the FTM2 clock source" |
| default PWM_K64_FTM_2_CLOCK_SOURCE_SYSTEM |
| |
| config PWM_K64_FTM_2_CLOCK_SOURCE_NONE |
| bool "No clock selected (FTM counter disable)" |
| |
| config PWM_K64_FTM_2_CLOCK_SOURCE_SYSTEM |
| bool "System clock" |
| |
| config PWM_K64_FTM_2_CLOCK_SOURCE_FIXED |
| bool "Fixed Frequency Clock" |
| |
| config PWM_K64_FTM_2_CLOCK_SOURCE_EXTERNAL |
| bool "External Clock" |
| |
| config PWM_K64_FTM_2_CLOCK_SOURCE_QUAD |
| bool "Quadrature Decoder" |
| |
| endchoice |
| |
| endmenu |
| |
| config PWM_K64_FTM_2_CLOCK_SOURCE |
| int |
| # Omit prompt to signify "hidden" option |
| depends on PWM_K64_FTM_2 |
| default 0 if PWM_K64_FTM_2_CLOCK_SOURCE_NONE |
| default 1 if PWM_K64_FTM_2_CLOCK_SOURCE_SYSTEM |
| default 2 if PWM_K64_FTM_2_CLOCK_SOURCE_FIXED |
| default 3 if PWM_K64_FTM_2_CLOCK_SOURCE_EXTERNAL |
| default 4 if PWM_K64_FTM_2_CLOCK_SOURCE_QUAD |
| help |
| Specify K64 FTM2 clock source |
| |
| config PWM_K64_FTM_2_PHASE_ENABLE_0 |
| bool "FTM2 Enable Phase for channel 0" |
| depends on PWM_K64_FTM_2 |
| default n |
| help |
| Allow a phase offset on FTM2 channel 0. This configures |
| channels 0 and 1 to be in combine mode therefore |
| channel 1 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_K64_FTM_2_PHASE_ENABLE_2 |
| bool "FTM2 Enable Phase for channel 2" |
| depends on PWM_K64_FTM_2 |
| default n |
| help |
| Allow a phase offset on FTM2 channel 2. This configures |
| channels 2 and 3 to be in combine mode therefore |
| channel 3 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_K64_FTM_2_PHASE_ENABLE_4 |
| bool "FTM2 Enable Phase for channel 4" |
| depends on PWM_K64_FTM_2 |
| default n |
| help |
| Allow a phase offset on FTM2 channel 4. This configures |
| channels 4 and 5 to be in combine mode therefore |
| channel 5 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_K64_FTM_2_PHASE_ENABLE_6 |
| bool "FTM2 Enable Phase for channel 6" |
| depends on PWM_K64_FTM_2 |
| default n |
| help |
| Allow a phase offset on FTM2 channel 6. This configures |
| channels 6 and 7 to be in combine mode therefore |
| channel 7 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| #### FTM3 ##### |
| |
| config PWM_K64_FTM_3 |
| bool "K64 FTM PWM Module 3" |
| depends on PWM_K64_FTM |
| default n |
| help |
| Enable config PWM options for K64 FTM3 source module. |
| |
| config PWM_K64_FTM_3_DEV_NAME |
| string "K64 FTM PWM Module 3 Device Name" |
| depends on PWM_K64_FTM_3 |
| default "PWM_3" |
| help |
| Specify the device name for the FTM3 source module. |
| |
| config PWM_K64_FTM_3_PRESCALE |
| int "FTM3 prescale value" |
| default 3 |
| depends on PWM_K64_FTM_3 |
| help |
| Specify the FTM timer prescale value. The valid values are |
| 1, 2, 4, 8, 16, 32, 64, or 128 |
| |
| config PWM_K64_FTM_3_PERIOD |
| int "FTM3 period value" |
| default 65535 |
| depends on PWM_K64_FTM_3 |
| help |
| Specify the FTM3 PWM period in ticks |
| |
| menu "K64 FTM3 Clock Source" |
| depends on PWM_K64_FTM_3 |
| |
| choice PWM_K64_FTM_3_CLOCK_SOURCE_CHOICE |
| prompt "Choose the FTM3 clock source" |
| default PWM_K64_FTM_3_CLOCK_SOURCE_SYSTEM |
| |
| config PWM_K64_FTM_3_CLOCK_SOURCE_NONE |
| bool "No clock selected (FTM counter disable)" |
| |
| config PWM_K64_FTM_3_CLOCK_SOURCE_SYSTEM |
| bool "System clock" |
| |
| config PWM_K64_FTM_3_CLOCK_SOURCE_FIXED |
| bool "Fixed Frequency Clock" |
| |
| config PWM_K64_FTM_3_CLOCK_SOURCE_EXTERNAL |
| bool "External Clock" |
| |
| config PWM_K64_FTM_3_CLOCK_SOURCE_QUAD |
| bool "Quadrature Decoder" |
| |
| endchoice |
| |
| endmenu |
| |
| config PWM_K64_FTM_3_CLOCK_SOURCE |
| int |
| # Omit prompt to signify "hidden" option |
| depends on PWM_K64_FTM_3 |
| default 0 if PWM_K64_FTM_3_CLOCK_SOURCE_NONE |
| default 1 if PWM_K64_FTM_3_CLOCK_SOURCE_SYSTEM |
| default 2 if PWM_K64_FTM_3_CLOCK_SOURCE_FIXED |
| default 3 if PWM_K64_FTM_3_CLOCK_SOURCE_EXTERNAL |
| default 4 if PWM_K64_FTM_3_CLOCK_SOURCE_QUAD |
| help |
| Specify K64 FTM3 clock source |
| |
| config PWM_K64_FTM_3_PHASE_ENABLE_0 |
| bool "FTM3 Enable Phase for channel 0" |
| depends on PWM_K64_FTM_3 |
| default n |
| help |
| Allow a phase offset on FTM3 channel 0. This configures |
| channels 0 and 1 to be in combine mode therefore |
| channel 1 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_K64_FTM_3_PHASE_ENABLE_2 |
| bool "FTM3 Enable Phase for channel 2" |
| depends on PWM_K64_FTM_3 |
| default n |
| help |
| Allow a phase offset on FTM3 channel 2. This configures |
| channels 2 and 3 to be in combine mode therefore |
| channel 3 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_K64_FTM_3_PHASE_ENABLE_4 |
| bool "FTM3 Enable Phase for channel 4" |
| depends on PWM_K64_FTM_3 |
| default n |
| help |
| Allow a phase offset on FTM3 channel 4. This configures |
| channels 4 and 5 to be in combine mode therefore |
| channel 5 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| config PWM_K64_FTM_3_PHASE_ENABLE_6 |
| bool "FTM3 Enable Phase for channel 6" |
| depends on PWM_K64_FTM_3 |
| default n |
| help |
| Allow a phase offset on FTM3 channel 6. This configures |
| channels 6 and 7 to be in combine mode therefore |
| channel 7 is not valid as an output signal. |
| Note: phase is an unsupported feature. |
| |
| endif # PWM_K64_FTM |
