| # Kconfig.beetle - ARM CMSDK APB SoC UART configuration options |
| # |
| # |
| # Copyright (c) 2016 Linaro Limited |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| menuconfig UART_CMSDK_APB |
| bool "ARM CMSDK APB UART driver" |
| default n |
| select SERIAL_HAS_DRIVER |
| depends on SOC_FAMILY_ARM |
| help |
| This option enables the UART driver for ARM CMSDK APB UART. |
| |
| if UART_CMSDK_APB |
| |
| # ---------- Port 0 ---------- |
| |
| config UART_CMSDK_APB_PORT0 |
| bool "Enable driver for UART 0" |
| default n |
| help |
| Build the driver to utilize UART controller Port 0. |
| |
| config UART_CMSDK_APB_PORT0_NAME |
| string "Device Name for UART 0" |
| default "UART_0" |
| depends on UART_CMSDK_APB_PORT0 |
| help |
| This is the device name for UART, and is included in the device |
| struct. |
| |
| config UART_CMSDK_APB_PORT0_IRQ_PRI |
| int "UART Interrupt Priority (Interrupt support)" |
| default 2 |
| depends on UART_CMSDK_APB_PORT0 |
| depends on UART_INTERRUPT_DRIVEN |
| help |
| The interrupt priority for UART port. |
| |
| config UART_CMSDK_APB_PORT0_BAUD_RATE |
| int "Baud Rate" |
| range 9600 115200 |
| default 115200 |
| depends on UART_CMSDK_APB_PORT0 |
| help |
| The baud rate for UART port to be set to at boot. |
| |
| # ---------- Port 1 ---------- |
| |
| config UART_CMSDK_APB_PORT1 |
| bool "Enable driver for UART 1" |
| default n |
| help |
| Build the driver to utilize UART controller Port 1. |
| |
| config UART_CMSDK_APB_PORT1_NAME |
| string "Device Name for UART 1" |
| default "UART_1" |
| depends on UART_CMSDK_APB_PORT1 |
| help |
| This is the device name for UART, and is included in the device |
| struct. |
| |
| config UART_CMSDK_APB_PORT1_IRQ_PRI |
| int "UART Interrupt Priority (Interrupt support)" |
| default 2 |
| depends on UART_CMSDK_APB_PORT1 |
| depends on UART_INTERRUPT_DRIVEN |
| help |
| The interrupt priority for UART port. |
| |
| config UART_CMSDK_APB_PORT1_BAUD_RATE |
| int "Baud Rate" |
| range 9600 115200 |
| default 115200 |
| depends on UART_CMSDK_APB_PORT1 |
| help |
| The baud rate for UART port to be set to at boot. |
| |
| # ---------- Port 2 ---------- |
| |
| config UART_CMSDK_APB_PORT2 |
| bool "Enable driver for UART 2" |
| default n |
| help |
| Build the driver to utilize UART controller Port 2. |
| |
| config UART_CMSDK_APB_PORT2_NAME |
| string "Device Name for UART 2" |
| default "UART_2" |
| depends on UART_CMSDK_APB_PORT2 |
| help |
| This is the device name for UART, and is included in the device |
| struct. |
| |
| config UART_CMSDK_APB_PORT2_IRQ_PRI |
| int "UART Interrupt Priority (Interrupt support)" |
| default 2 |
| depends on UART_CMSDK_APB_PORT2 |
| depends on UART_INTERRUPT_DRIVEN |
| help |
| The interrupt priority for UART port. |
| |
| config UART_CMSDK_APB_PORT2_BAUD_RATE |
| int "Baud Rate" |
| range 9600 115200 |
| default 115200 |
| depends on UART_CMSDK_APB_PORT2 |
| help |
| The baud rate for UART port to be set to at boot. |
| |
| # ---------- Port 3 ---------- |
| |
| config UART_CMSDK_APB_PORT3 |
| bool "Enable driver for UART 3" |
| default n |
| help |
| Build the driver to utilize UART controller Port 3. |
| |
| config UART_CMSDK_APB_PORT3_NAME |
| string "Device Name for UART 3" |
| default "UART_3" |
| depends on UART_CMSDK_APB_PORT3 |
| help |
| This is the device name for UART, and is included in the device |
| struct. |
| |
| config UART_CMSDK_APB_PORT3_IRQ_PRI |
| int "UART Interrupt Priority (Interrupt support)" |
| default 2 |
| depends on UART_CMSDK_APB_PORT3 |
| depends on UART_INTERRUPT_DRIVEN |
| help |
| The interrupt priority for UART port. |
| |
| config UART_CMSDK_APB_PORT3_BAUD_RATE |
| int "Baud Rate" |
| range 9600 115200 |
| default 115200 |
| depends on UART_CMSDK_APB_PORT3 |
| help |
| The baud rate for UART port to be set to at boot. |
| |
| # ---------- Port 4 ---------- |
| |
| config UART_CMSDK_APB_PORT4 |
| bool "Enable driver for UART 4" |
| default n |
| help |
| Build the driver to utilize UART controller Port 4. |
| |
| config UART_CMSDK_APB_PORT4_NAME |
| string "Device Name for UART 4" |
| default "UART_4" |
| depends on UART_CMSDK_APB_PORT4 |
| help |
| This is the device name for UART, and is included in the device |
| struct. |
| |
| config UART_CMSDK_APB_PORT4_IRQ_PRI |
| int "UART Interrupt Priority (Interrupt support)" |
| default 2 |
| depends on UART_CMSDK_APB_PORT4 |
| depends on UART_INTERRUPT_DRIVEN |
| help |
| The interrupt priority for UART port. |
| |
| config UART_CMSDK_APB_PORT4_BAUD_RATE |
| int "Baud Rate" |
| range 9600 115200 |
| default 115200 |
| depends on UART_CMSDK_APB_PORT4 |
| help |
| The baud rate for UART port to be set to at boot. |
| |
| endif # UART_CMSDK_APB |
