| /* |
| * Copyright (c) 2019 Roland Ma |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /dts-v1/; |
| #include <st/f7/stm32f767Xi.dtsi> |
| #include "arduino_r3_connector.dtsi" |
| |
| / { |
| model = "STMicroelectronics STM32F767ZI-NUCLEO board"; |
| compatible = "st,stm32f767zi-nucleo", "st,stm32f767"; |
| |
| chosen { |
| zephyr,console = &usart3; |
| zephyr,shell-uart = &usart3; |
| zephyr,sram = &sram0; |
| zephyr,flash = &flash0; |
| zephyr,code-partition = &slot0_partition; |
| zephyr,dtcm = &dtcm; |
| zephyr,can-primary = &can1; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| green_led: led_0 { |
| gpios = <&gpiob 0 GPIO_ACTIVE_HIGH>; |
| label = "User LD1"; |
| }; |
| blue_led: led_1 { |
| gpios = <&gpiob 7 GPIO_ACTIVE_HIGH>; |
| label = "User LD2"; |
| }; |
| red_led: led_2 { |
| gpios = <&gpiob 14 GPIO_ACTIVE_HIGH>; |
| label = "User LD3"; |
| }; |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| user_button: button_0 { |
| label = "User"; |
| gpios = <&gpioc 13 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| aliases { |
| led0 = &green_led; |
| led1 = &blue_led; |
| led2 = &red_led; |
| sw0 = &user_button; |
| }; |
| }; |
| |
| &usart3 { |
| current-speed = <115200>; |
| status = "okay"; |
| }; |
| |
| &usart6 { |
| current-speed = <115200>; |
| status = "okay"; |
| }; |
| |
| &usbotg_fs { |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| clock-frequency = <I2C_BITRATE_FAST>; |
| }; |
| |
| &timers1 { |
| status = "okay"; |
| |
| pwm1: pwm { |
| status = "okay"; |
| }; |
| }; |
| |
| &spi1 { |
| /* |
| * WARNING: The pin PA7 will conflict on selection of SPI_1 and |
| * ETH_STM32_HAL. See pinmux.c for further details. |
| */ |
| status = "okay"; |
| }; |
| |
| &iwdg { |
| status = "okay"; |
| }; |
| |
| &rtc { |
| status = "okay"; |
| }; |
| |
| &can1 { |
| bus-speed = <125000>; |
| sjw = <1>; |
| prop-seg = <0>; |
| phase-seg1 = <6>; |
| phase-seg2 = <5>; |
| status = "okay"; |
| }; |
| |
| &adc1 { |
| status = "okay"; |
| }; |
| |
| &rng { |
| status = "okay"; |
| }; |
| |
| &mac { |
| status = "okay"; |
| }; |
| |
| &flash0 { |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| /* |
| * The two sectors 0-1 (32+32 kbytes) are reserved for |
| * the bootloader. |
| */ |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x0 0x00010000>; |
| read-only; |
| }; |
| |
| /* |
| * The flash starting at offset 0x10000 and ending at |
| * offset 0x1ffff is reserved for use by the application. |
| * This represents sectors 2-3 (32+32 kbytes) |
| */ |
| storage_partition: partition@10000 { |
| label = "storage"; |
| reg = <0x00010000 0x00010000>; |
| }; |
| |
| /* |
| * Sector 4 (128 kbytes) unallocated. |
| */ |
| |
| /* |
| * Allocated 3 (256k x 3) sectors for image-0. Sectors 5-7. |
| */ |
| slot0_partition: partition@40000 { |
| label = "image-0"; |
| reg = <0x00040000 0x000C0000>; |
| }; |
| |
| /* |
| * Allocated 3 (256k x 3) sectors for image-1. Sectors 8-10. |
| */ |
| slot1_partition: partition@100000 { |
| label = "image-1"; |
| reg = <0x00100000 0x000C0000>; |
| }; |
| |
| /* |
| * Allocated 1 (256k) sector for image-scratch. Sector 11. |
| */ |
| scratch_partition: partition@1C0000 { |
| label = "image-scratch"; |
| reg = <0x001C0000 0x00040000>; |
| }; |
| }; |
| }; |