| # Zephyr Bluetooth Controller configuration options |
| |
| # Copyright (c) 2016-2017 Nordic Semiconductor ASA |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| if BT_LL_SW_SPLIT |
| |
| config BT_LLL_VENDOR_NORDIC |
| bool "Use Nordic LLL" |
| depends on SOC_COMPATIBLE_NRF |
| select BT_HAS_HCI_VS |
| select ENTROPY_NRF5_RNG |
| select ENTROPY_NRF5_BIAS_CORRECTION |
| select BT_CTLR_LE_ENC_SUPPORT if !BT_CTLR_DATA_LENGTH_CLEAR && \ |
| !BT_CTLR_PHY_2M_NRF |
| select BT_CTLR_CONN_PARAM_REQ_SUPPORT |
| select BT_CTLR_EXT_REJ_IND_SUPPORT |
| select BT_CTLR_PER_INIT_FEAT_XCHG_SUPPORT |
| select BT_CTLR_DATA_LEN_UPDATE_SUPPORT if HAS_HW_NRF_CCM_LFLEN_8BIT || \ |
| BT_CTLR_DATA_LENGTH_CLEAR |
| select BT_CTLR_PRIVACY_SUPPORT if !SOC_SERIES_NRF51X |
| select BT_CTLR_EXT_SCAN_FP_SUPPORT |
| |
| select BT_CTLR_PHY_2M_SUPPORT if HAS_HW_NRF_RADIO_BLE_2M || \ |
| BT_CTLR_PHY_2M_NRF |
| select BT_CTLR_PHY_CODED_SUPPORT if HAS_HW_NRF_RADIO_BLE_CODED |
| select BT_CTLR_PHY_UPDATE_SUPPORT if BT_CTLR_PHY_2M_SUPPORT || \ |
| BT_CTLR_PHY_CODED_SUPPORT |
| select BT_CTLR_ADV_EXT_SUPPORT |
| select BT_CTLR_ADV_PERIODIC_SUPPORT |
| select BT_CTLR_SYNC_PERIODIC_SUPPORT |
| select BT_CTLR_ADV_ISO_SUPPORT |
| select BT_CTLR_SYNC_ISO_SUPPORT |
| select BT_CTLR_CENTRAL_ISO_SUPPORT |
| select BT_CTLR_PERIPHERAL_ISO_SUPPORT |
| select BT_CTLR_DF_SUPPORT if HAS_HW_NRF_RADIO_DFE |
| select BT_CTLR_CTEINLINE_SUPPORT if HAS_HW_NRF_RADIO_DFE |
| select BT_CTLR_CHAN_SEL_2_SUPPORT |
| select BT_CTLR_MIN_USED_CHAN_SUPPORT |
| select BT_CTLR_SCA_UPDATE_SUPPORT if !BT_LL_SW_LLCP_LEGACY |
| select BT_CTLR_DTM_HCI_SUPPORT |
| select BT_CTLR_CONN_RSSI_SUPPORT |
| |
| select BT_CTLR_XTAL_ADVANCED_SUPPORT |
| select BT_CTLR_SCHED_ADVANCED_SUPPORT |
| select BT_CTLR_TIFS_HW_SUPPORT |
| select BT_CTLR_ULL_LLL_PRIO_SUPPORT |
| |
| select BT_TICKER_UPDATE if BT_BROADCASTER || BT_CONN || \ |
| (BT_OBSERVER && BT_CTLR_ADV_EXT) |
| select BT_TICKER_NEXT_SLOT_GET if (BT_BROADCASTER && \ |
| BT_CTLR_ADV_EXT) || \ |
| BT_CTLR_ADV_PERIODIC |
| select BT_TICKER_REMAINDER_GET if BT_BROADCASTER && BT_CTLR_ADV_EXT |
| select BT_TICKER_LAZY_GET if BT_CTLR_ADV_PERIODIC |
| |
| default y |
| help |
| Use Nordic Lower Link Layer implementation. |
| |
| config BT_LLL_VENDOR_OPENISA |
| bool "Use OpenISA LLL" |
| depends on SOC_OPENISA_RV32M1_RISCV32 |
| select BT_CTLR_PHY_UPDATE_SUPPORT |
| select BT_CTLR_EXT_REJ_IND_SUPPORT |
| select BT_HAS_HCI_VS |
| select BT_CTLR_LE_ENC_SUPPORT if !BT_CTLR_DATA_LENGTH_CLEAR |
| select BT_CTLR_PRIVACY_SUPPORT |
| |
| select BT_TICKER_UPDATE if BT_BROADCASTER || BT_CONN |
| |
| default y |
| help |
| Use OpenISA Lower Link Layer implementation. |
| |
| config BT_CTLR_XTAL_ADVANCED_SUPPORT |
| bool |
| |
| config BT_CTLR_SCHED_ADVANCED_SUPPORT |
| bool |
| |
| config BT_CTLR_TIFS_HW_SUPPORT |
| bool |
| |
| config BT_CTLR_ULL_LLL_PRIO_SUPPORT |
| bool |
| |
| choice BT_LL_SW_LLCP_IMPL |
| prompt "Bluetooth Low Energy Software Link Layer Control Procedure Implementation" |
| default BT_LL_SW_LLCP |
| help |
| Select the Bluetooth Low Energy Software Link Layer Control Procedure implementation. |
| |
| config BT_LL_SW_LLCP_LEGACY |
| bool "Legacy implementation (DEPRECATED)" |
| depends on !BT_CTLR_DF_CONN_CTE_RX && !BT_CTLR_DF_CONN_CTE_TX |
| select DEPRECATED |
| help |
| Use the Bluetooth Low Energy Software Link Layer Legacy Control Procedure implementation. |
| |
| config BT_LL_SW_LLCP |
| bool "State-machine based implementation, replacing the legacy one" |
| help |
| Use the new Bluetooth Low Energy Software Link Layer Control Procedure implementation. |
| |
| endchoice |
| |
| |
| config BT_CTLR_RX_PRIO_STACK_SIZE |
| # Controller's Co-Operative high priority Rx thread stack size. |
| int "High priority Rx thread stack size" |
| default 448 |
| |
| config BT_CTLR_SETTINGS |
| bool "Settings System" |
| depends on SETTINGS |
| help |
| Enable use of settings system in controller. |
| |
| config BT_CTLR_VERSION_SETTINGS |
| bool "Version Settings" |
| depends on BT_CTLR_SETTINGS |
| help |
| Make the controller's Company Id and Subversion Number configurable |
| through settings system. |
| |
| config BT_CTLR_COMPANY_ID |
| hex "Controller Company Id" |
| default BT_COMPANY_ID |
| range 0x0000 0xFFFF |
| help |
| Set the Bluetooth Company Identifier that will be used in |
| the VERSION_IND PDU. Uses BT_COMPANY_ID by default, although |
| silicon vendors and hardware manufacturers can set their own |
| Company Identifier for the controller. The full list of Bluetooth |
| Company Identifiers can be found here: |
| https://www.bluetooth.com/specifications/assigned-numbers/company-identifiers |
| |
| config BT_CTLR_SUBVERSION_NUMBER |
| hex "Subversion Number" |
| default 0xFFFF |
| range 0x0000 0xFFFF |
| help |
| Set the Subversion Number that will be used in VERSION_IND PDU. |
| |
| config BT_CTLR_ADVANCED_FEATURES |
| bool "Show advanced features" |
| help |
| Makes advanced features visible to controller developers. |
| |
| menu "Advanced features" |
| visible if BT_CTLR_ADVANCED_FEATURES |
| |
| config BT_CTLR_SW_DEFERRED_PRIVACY |
| bool "LE Controller-based Software Privacy" |
| depends on BT_CTLR_PRIVACY |
| help |
| Enable support for software based deferred privacy calculations. |
| |
| config BT_CTLR_RPA_CACHE_SIZE |
| int "LE Controller-based Software Privacy Resolving List size" |
| depends on BT_CTLR_SW_DEFERRED_PRIVACY |
| default 8 |
| range 1 64 |
| help |
| Set the size of the Known Unknown Resolving List for LE |
| Controller-based Software deferred Privacy. |
| |
| config BT_CTLR_DATA_LENGTH_CLEAR |
| bool "Data Length Support (Cleartext only)" |
| depends on SOC_SERIES_NRF51X |
| help |
| Enable support for Bluetooth v4.2 LE Data Length Update procedure, up to |
| 251 byte cleartext payloads in the Controller. Encrypted connections |
| are not supported. |
| |
| |
| config BT_CTLR_PHY_2M_NRF |
| bool "2Mbps Nordic Semiconductor PHY Support (Cleartext only)" |
| depends on SOC_SERIES_NRF51X |
| select BT_CTLR_PHY_2M |
| help |
| Enable support for Nordic Semiconductor proprietary 2Mbps PHY in the |
| Controller. Encrypted connections are not supported. |
| |
| config BT_CTLR_ADV_AUX_SET |
| int "LE Extended Advertising Auxiliary Sets" |
| depends on BT_BROADCASTER && BT_CTLR_ADV_EXT |
| range 1 BT_CTLR_ADV_SET if BT_CTLR_ADV_PERIODIC |
| range 0 BT_CTLR_ADV_SET |
| default 1 if BT_CTLR_ADV_PERIODIC |
| default BT_CTLR_ADV_SET |
| help |
| Maximum supported advertising auxiliary channel sets. |
| |
| config BT_CTLR_ADV_SYNC_SET |
| int "LE Periodic Advertising Sets" |
| depends on BT_CTLR_ADV_PERIODIC |
| range 1 BT_CTLR_ADV_AUX_SET |
| default 1 |
| help |
| Maximum supported periodic advertising sets. |
| |
| config BT_CTLR_ADV_DATA_CHAIN |
| bool "Advertising Data chaining [EXPERIMENTAL]" |
| select EXPERIMENTAL |
| help |
| Enable support for Advertising Data chaining in Extended and |
| Periodic Advertising. This will allow to have Advertising Data Length |
| upto 1650 bytes. |
| |
| This is experimental and work in progress, does not implement |
| recombining the AD Data and could return BT_HCI_ERR_PACKET_TOO_LONG |
| when a chain PDU needs its AD data overflow into a new chain PDU. |
| I.e. AD data in the last PDU could overflow due to the need to add |
| Aux Pointer field, and if this overflow bytes plus the next AD data |
| fragment length could be over 255 bytes needing additional chain PDU. |
| This is not implemented. |
| |
| config BT_CTLR_ADV_PDU_LINK |
| # Enables extra space in each advertising PDU to allow linking PDUs. |
| # This is required to enable advertising data trains (i.e. transmission |
| # of AUX_CHAIN_IND). |
| bool |
| |
| config BT_CTLR_ADV_AUX_PDU_LINK |
| # Enable chaining in Extended Advertising |
| bool |
| select BT_CTLR_ADV_PDU_LINK |
| |
| config BT_CTLR_ADV_AUX_PDU_BACK2BACK |
| bool "Back-to-back transmission of extended advertising trains" |
| depends on BT_BROADCASTER && BT_CTLR_ADV_EXT |
| select BT_CTLR_ADV_AUX_PDU_LINK |
| default y if BT_CTLR_ADV_DATA_LEN_MAX > 191 |
| help |
| Enables transmission of AUX_CHAIN_IND in extended advertising train by |
| sending each AUX_CHAIN_IND one after another back-to-back. |
| |
| config BT_CTLR_ADV_AUX_PDU_BACK2BACK_AFS |
| int "AUX Frame Space for back-to-back transmission of extended advertising trains" |
| depends on BT_CTLR_ADV_AUX_PDU_BACK2BACK |
| range 300 1000 |
| default 300 |
| help |
| Specific AUX Frame Space to be used for back-to-back transmission of |
| extended advertising trains. Time specified in microseconds. |
| |
| config BT_CTLR_ADV_SYNC_PDU_LINK |
| bool |
| depends on BT_CTLR_ADV_PERIODIC |
| select BT_CTLR_ADV_PDU_LINK |
| |
| config BT_CTLR_ADV_SYNC_PDU_BACK2BACK |
| bool "Back-to-back transmission of periodic advertising trains" |
| depends on BT_CTLR_ADV_PERIODIC |
| select BT_CTLR_ADV_SYNC_PDU_LINK |
| help |
| Enables transmission of AUX_CHAIN_IND in periodic advertising train by |
| sending each AUX_CHAIN_IND one after another back-to-back. |
| Note, consecutive AUX_CHAIN_IND packets are not scheduled but sent at |
| a constant offset on a best effort basis. This means advertising train can |
| be preempted by other event at any time. |
| |
| config BT_CTLR_ADV_SYNC_PDU_BACK2BACK_AFS |
| int "AUX Frame Space for back-to-back transmission of periodic advertising trains" |
| depends on BT_CTLR_ADV_SYNC_PDU_BACK2BACK |
| range 300 1000 |
| default 300 |
| help |
| Specific AUX Frame Space to be used for back-to-back transmission of |
| periodic advertising trains. Time specified in microseconds. |
| |
| config BT_CTLR_ADV_RESERVE_MAX |
| bool "Use maximum Advertising PDU size time reservation" |
| depends on BT_BROADCASTER && BT_CTLR_ADV_EXT |
| default y |
| help |
| Use the maximum advertising PDU size time reservation considering the |
| Advertising Data could be updated from zero to maximum support size. |
| If maximum time reservation is disabled then time reservation |
| corresponding to the Advertising Data present at the time of the |
| start/enable of Advertising is used. |
| |
| config BT_CTLR_ADV_DATA_BUF_MAX |
| int "Advertising Data Maximum Buffers" |
| depends on BT_BROADCASTER |
| range 1 64 if BT_CTLR_ADV_EXT |
| range 1 1 if !BT_CTLR_ADV_EXT |
| default 1 |
| help |
| Maximum number of buffered Advertising Data payload across enabled |
| advertising sets. |
| |
| config BT_CTLR_ADV_EXT_PDU_EXTRA_DATA_MEMORY |
| bool |
| depends on BT_CTLR_ADV_EXT |
| help |
| Add additional memory to advertising PDU storage. The memory is a |
| general purpose storage for data that should be send from ULL to LLL. |
| The data stored in the memory are in synchronization with content |
| of PDU memory. |
| |
| For example, the extra data memory is used for storage for parameters |
| to configure Radio peripheral to transmit CTE. The configuration data |
| must be synchronized with CTEInfo field in extended advertising header |
| that is part of PDU data. |
| |
| config BT_CTRL_ADV_ADI_IN_SCAN_RSP |
| bool "Include ADI in AUX_SCAN_RSP PDU" |
| depends on BT_BROADCASTER && BT_CTLR_ADV_EXT |
| help |
| Enable ADI field in AUX_SCAN_RSP PDU |
| |
| config BT_CTLR_SCAN_AUX_SYNC_RESERVE_MIN |
| bool "Use minimal Scan Auxiliary and Periodic Sync PDU time reservation" |
| depends on (BT_OBSERVER && BT_CTLR_ADV_EXT) || BT_CTLR_SYNC_PERIODIC |
| default y |
| help |
| Use minimal time reservation for Auxiliary and Periodic Sync PDU |
| reception. A peer device could scheduling multiple advertising sets |
| in a short duration with small PDUs hence using the minimal time |
| reservation would avoid skipping closely scheduled reception of |
| multiple Auxiliary or Periodic Sync PDUs. |
| |
| config BT_CTLR_SYNC_PERIODIC_SKIP_ON_SCAN_AUX |
| bool "Skip Periodic Sync event on overlap with Extended Scan Event" |
| depends on BT_CTLR_SYNC_PERIODIC |
| help |
| When AUX_ADV_IND or AUX_CHAIN_IND auxiliary channel PDU scan radio |
| event overlaps Periodic Sync radio event in unreserved time space, |
| let the Periodic Sync radio event be aborted so that the auxiliary |
| channel PDU can be received to generate Extended Advertising Reports. |
| |
| By default we want Periodic Advertising Sync Events to take priority |
| over any overlapping Extended Advertising Primary and Auxiliary |
| channel PDU reception in order to not skip Periodic Advertising Report |
| generation. |
| |
| But under simultaneous multiple Periodic Advertising Sync support with |
| small Periodic Advertising Intervals where there will be a lot of |
| overlapping Periodic Advertising Sync events, it is desirable to |
| permit Extended Advertising auxiliary PDU reception be allowed in a |
| round robin scheduling to skip the overlapping Periodic Advertising |
| Sync event. This permits new Periodic Advertising peers be discovered. |
| |
| config BT_CTLR_SCAN_AUX_SET |
| int "LE Extended Scanning Auxiliary Sets" |
| depends on BT_OBSERVER && BT_CTLR_ADV_EXT |
| range 1 64 |
| default 1 |
| help |
| Maximum supported auxiliary channel scan sets. |
| |
| config BT_CTLR_SCAN_SYNC_ISO_SET |
| int "LE ISO Broadcast Isochronous Groups Sync Sets" |
| depends on BT_CTLR_SYNC_ISO |
| range 1 64 |
| default 1 |
| help |
| Maximum supported broadcast isochronous groups (BIGs) sync sets. |
| |
| config BT_CTLR_ADV_ENABLE_STRICT |
| bool "Enforce Strict Advertising Enable/Disable" |
| depends on BT_BROADCASTER |
| help |
| Enforce returning HCI Error Command Disallowed on enabling/disabling |
| already enabled/disabled advertising. |
| |
| config BT_CTLR_SCAN_ENABLE_STRICT |
| bool "Enforce Strict Scan Enable/Disable" |
| depends on BT_OBSERVER |
| help |
| Enforce returning HCI Error Command Disallowed on enabling/disabling |
| already enabled/disabled scanning. |
| |
| config BT_CTLR_ZLI |
| bool "Use Zero Latency IRQs" |
| depends on ZERO_LATENCY_IRQS |
| default y |
| help |
| Enable support for use of Zero Latency IRQ feature. Note, applications |
| shall not use Zero Latency IRQ themselves when this option is selected, |
| else will impact controller stability. |
| |
| config BT_CTLR_OPTIMIZE_FOR_SPEED |
| prompt "Optimize for Speed" if !(SOC_SERIES_NRF51X && BT_CTLR_LE_ENC) |
| bool |
| default y if BT_CTLR_LE_ENC |
| help |
| Optimize compilation of controller for execution speed. |
| |
| config BT_CTLR_XTAL_ADVANCED |
| bool "Advanced event preparation" |
| depends on BT_CTLR_XTAL_ADVANCED_SUPPORT |
| default y |
| help |
| Enables advanced event preparation offset ahead of radio tx/rx, taking |
| into account predictive processing time requirements in preparation to |
| the event, like control procedure handling and CPU execution speeds. |
| Crystal oscillator is retained between closely spaced consecutive |
| radio events to reduce the overall number of crystal settling current |
| consumptions. |
| |
| This feature maximizes radio utilization in an average role event |
| timeslice when they are closely spaced by using a reduced offset |
| between preparation and radio event. |
| |
| By disabling this feature, the controller will use a constant offset |
| between the preparation and radio event. The controller will toggle |
| crystal oscillator between two closely spaced radio events leading to |
| higher average current due to increased number of crystal settling |
| current consumptions. |
| |
| config BT_CTLR_XTAL_THRESHOLD |
| int "Crystal shutdown threshold in uS" |
| depends on BT_CTLR_XTAL_ADVANCED |
| default 1500 |
| help |
| Configure the optimal delta in micro seconds between two consecutive |
| radio events, event done to next preparation, below which (active |
| clock) crystal will be retained. This value is board dependent. |
| |
| config BT_CTLR_SCHED_ADVANCED |
| bool "Advanced scheduling" |
| depends on BT_CTLR_SCHED_ADVANCED_SUPPORT && \ |
| (BT_CONN || \ |
| (BT_CTLR_ADV_EXT && (BT_CTLR_ADV_AUX_SET > 1)) || \ |
| BT_CTLR_ADV_ISO) |
| default y if BT_CENTRAL || (BT_BROADCASTER && BT_CTLR_ADV_EXT) || BT_CTLR_ADV_ISO |
| help |
| Enable non-overlapping placement of observer, initiator and central |
| roles in timespace. Uses window offset in connection updates and uses |
| connection parameter request in peripheral role to negotiate |
| non-overlapping placement with active central roles to avoid peripheral |
| roles drifting into active central roles in the local controller. |
| |
| This feature maximizes the average data transmission amongst active |
| concurrent central and peripheral connections while other observer, |
| initiator, central or peripheral roles are active in the local controller. |
| |
| Disabling this feature will lead to overlapping role in timespace |
| leading to skipped events amongst active roles. |
| |
| config BT_CTLR_CENTRAL_SPACING |
| int "Central Connection Spacing" |
| depends on BT_CTLR_SCHED_ADVANCED |
| default 0 |
| range 0 65535 |
| help |
| The preferred connection spacing between multiple simultaneous central |
| roles in microseconds. The Controller will calculate the required time |
| reservation using the data length and PHY currently in use. The |
| greater of the preferred spacing and the calculated time reservation |
| will be used. |
| The precision is determined by the resolution of the platform |
| dependent ticker clock. |
| The upper range is a ceil value permitting any tuning of Controller's |
| radio handling overheads and to allow Coded PHY S8 coding scheme PDU |
| time, i.e. radio event overheads + 17040 (PDU Tx) + 150 (tIFS) + 4 |
| (active clock jitter) + 17040 (PDU rx) = (radio event overheads + |
| 34234) microseconds. |
| |
| config BT_CTLR_CENTRAL_RESERVE_MAX |
| bool "Use maximum data PDU size time reservation for Central" |
| depends on BT_CENTRAL |
| default y |
| help |
| Use the maximum data PDU size time reservation considering the Data |
| length could be updated from default 27 bytes to maximum support size. |
| If maximum time reservation is disabled then time reservation |
| corresponding to the default data length at the time of the |
| start/enable of Central role is used. |
| |
| Note, currently this value is only used to space multiple central |
| connections and not for actual ticker time reservations. |
| |
| config BT_CTLR_SLOT_RESERVATION_UPDATE |
| bool "Update event length reservation after PHY or DLE update" |
| depends on !BT_LL_SW_LLCP_LEGACY && (BT_CTLR_DATA_LENGTH || BT_CTLR_PHY) |
| default y |
| help |
| Updates the event length reservation after a completed Data Length Update |
| and/or PHY Update procedure to avoid overlap of radio events |
| |
| config BT_CTLR_LLL_PRIO |
| int "Lower Link Layer (Radio) IRQ priority" if (BT_CTLR_ULL_LLL_PRIO_SUPPORT && !BT_CTLR_ZLI) |
| range 0 3 if SOC_SERIES_NRF51X |
| range 0 6 if (SOC_SERIES_NRF52X || SOC_SERIES_NRF53X) |
| default 0 |
| help |
| The interrupt priority for event preparation and radio IRQ. |
| |
| config BT_CTLR_ULL_HIGH_PRIO |
| int "Upper Link Layer High IRQ priority" if BT_CTLR_ULL_LLL_PRIO_SUPPORT |
| range BT_CTLR_LLL_PRIO 3 if SOC_SERIES_NRF51X |
| range BT_CTLR_LLL_PRIO 6 if (SOC_SERIES_NRF52X || SOC_SERIES_NRF53X) |
| default BT_CTLR_LLL_PRIO if (!BT_CTLR_ULL_LLL_PRIO_SUPPORT || BT_CTLR_ZLI || BT_CTLR_LOW_LAT) |
| default 1 |
| help |
| The interrupt priority for Ticker's Worker IRQ and Upper Link Layer |
| higher priority functions. |
| |
| config BT_CTLR_ULL_LOW_PRIO |
| int "Upper Link Layer Low IRQ priority" if BT_CTLR_ULL_LLL_PRIO_SUPPORT |
| range BT_CTLR_ULL_HIGH_PRIO 3 if SOC_SERIES_NRF51X |
| range BT_CTLR_ULL_HIGH_PRIO 6 if (SOC_SERIES_NRF52X || SOC_SERIES_NRF53X) |
| default BT_CTLR_ULL_HIGH_PRIO |
| help |
| The interrupt priority for Ticker's Job IRQ and Upper Link Layer |
| lower priority functions. |
| |
| config BT_CTLR_LOW_LAT |
| bool "Low latency non-negotiating event preemption" |
| select BT_CTLR_LOW_LAT_ULL_DONE |
| default y if SOC_SERIES_NRF51X |
| help |
| Use low latency non-negotiating event preemption. This reduces |
| Radio ISR latencies by the controller event scheduling framework. |
| Consequently, this reduces on-air radio utilization due to redundant |
| radio state switches. |
| |
| config BT_CTLR_LOW_LAT_ULL |
| prompt "Low latency ULL" |
| bool |
| depends on BT_CTLR_LOW_LAT |
| default y |
| help |
| Low latency ULL implementation that uses tailchaining instead of while |
| loop to demux rx messages from LLL. |
| |
| config BT_CTLR_LOW_LAT_ULL_DONE |
| prompt "Low latency ULL prepare dequeue" |
| bool |
| help |
| Done events be processed and dequeued in ULL context. |
| |
| config BT_CTLR_CONN_META |
| prompt "Connection meta data extension" |
| bool |
| help |
| Enables vendor specific per-connection meta data as part of the |
| LLL connection object. |
| |
| config BT_CTLR_RX_PDU_META |
| prompt "RX pdu meta data" |
| bool |
| |
| config BT_CTLR_RADIO_ENABLE_FAST |
| bool "Use tTXEN/RXEN,FAST ramp-up" |
| depends on SOC_COMPATIBLE_NRF52X || SOC_SERIES_NRF53X |
| default y |
| help |
| Enable use of fast radio ramp-up mode. |
| |
| config BT_CTLR_TIFS_HW |
| bool "H/w Accelerated tIFS Trx switching" |
| depends on !BT_CTLR_RADIO_ENABLE_FAST && BT_CTLR_TIFS_HW_SUPPORT |
| default y |
| help |
| Enable use of hardware accelerated tIFS Trx switching. |
| |
| config BT_CTLR_SW_SWITCH_SINGLE_TIMER |
| bool "Single TIMER tIFS Trx SW switching" |
| depends on (!BT_CTLR_TIFS_HW) && (SOC_COMPATIBLE_NRF52X || SOC_SERIES_NRF53X) |
| help |
| Implement the tIFS Trx SW switch with the same TIMER |
| instance, as the one used for BLE event timing. Requires |
| SW switching be enabled. Using a single TIMER: |
| (+) frees up one TIMER instance |
| (+) removes jitter for HCTO implementation |
| (-) introduces drifting to the absolute time inside BLE |
| events, that increases linearly with the number of |
| packets exchanged in the event |
| (-) makes it impossible to use most of the pre-programmed |
| PPI channels for the controller, resulting in 4 channels |
| less left for other uses |
| |
| config BT_CTLR_PARAM_CHECK |
| bool "HCI Command Parameter checking" |
| default y if BT_HCI_RAW |
| help |
| Enable code checking HCI Command Parameters. This is not needed in |
| combined host plus controller builds, saving some code space. |
| |
| if BT_CONN |
| |
| config BT_CTLR_FAST_ENC |
| bool "Fast Encryption Setup" |
| depends on BT_CTLR_LE_ENC |
| default y if BT_HCI_RAW |
| help |
| Enable connection encryption setup in 4 connection events. |
| Peripheral will respond to Encryption Request with Encryption Response |
| in the next connection event, and will transmit Start Encryption |
| Request PDU in the same connection event, hence completing encryption |
| setup in 4 connection events. Encrypted data would be transmitted as |
| fast as in 4th connection event from Encryption Request. |
| |
| config BT_CTLR_LLCP_CONN |
| int "Number of connections with worst-case overlapping procedures" |
| default BT_MAX_CONN |
| range 1 BT_MAX_CONN |
| help |
| Set the number connections for which worst-case buffer requirements |
| for LLCP procedures must be met. Executing LLCP procedures on |
| more than this number of connections simultaneously may cause |
| instabilities. |
| |
| if !BT_LL_SW_LLCP_LEGACY |
| config BT_CTLR_LLCP_TX_PER_CONN_TX_CTRL_BUF_NUM_MAX |
| int |
| default 4 |
| help |
| The theoretical maximum number of tx ctrl buffers needed for any connection, is 4. |
| two for active encryption procedure plus one for rejecting a remote request |
| and one for a local terminate |
| |
| config BT_CTLR_LLCP_PER_CONN_TX_CTRL_BUF_NUM |
| int "Number of tx control buffers to be reserved per connection" |
| default BT_CTLR_LLCP_TX_PER_CONN_TX_CTRL_BUF_NUM_MAX |
| range 0 BT_CTLR_LLCP_TX_PER_CONN_TX_CTRL_BUF_NUM_MAX |
| help |
| Set the number control buffers that is to be pre allocated per connection |
| This defines the minimum number of buffers available for any connection |
| Setting this to non zero will ensure a connection will always have access |
| to buffer(s) for control procedure TX |
| |
| config BT_CTLR_LLCP_COMMON_TX_CTRL_BUF_NUM |
| int "Number of tx control buffers to be available across all connections" |
| default 0 |
| range 0 255 |
| help |
| Set the number control buffers that is to be available for tx. |
| This defines the size of the pool of tx buffers available |
| for control procedure tx. This pool is shared across all |
| procedures/connections with allocation through a fifo queue. |
| Configure between 0 and (4 - BT_CTLR_LLCP_PER_CONN_TX_CTRL_BUF_NUM) * BT_CTLR_LLCP_CONN |
| |
| config BT_CTLR_LLCP_LOCAL_PROC_CTX_BUF_NUM |
| int "Number of local control procedure contexts to be available across all connections" |
| default 6 if (BT_AUTO_PHY_UPDATE=y || BT_AUTO_DATA_LEN_UPDATE=y) && BT_CTLR_LLCP_CONN < 4 |
| default 2 if BT_CTLR_LLCP_CONN = 1 |
| default BT_CTLR_LLCP_CONN if BT_CTLR_LLCP_CONN > 1 |
| range 2 255 |
| help |
| Set the number control procedure contexts that is to be available. |
| This defines the size of the pool of control procedure contexts available |
| for handling local initiated control procedures. |
| This pool is shared across all connections, with allocation through a queue. |
| |
| config BT_CTLR_LLCP_REMOTE_PROC_CTX_BUF_NUM |
| int "Number of remote control procedure contexts to be available across all connections" |
| default BT_CTLR_LLCP_CONN |
| range 1 255 |
| help |
| Set the number control procedure contexts that is to be available. |
| This defines the size of the pool of control procedure contexts available |
| for handling remote initiated control procedures. |
| This pool is shared across all connections, with allocation through a queue. |
| |
| endif #!BT_LL_SW_LLCP_LEGACY |
| |
| |
| config BT_CTLR_LLID_DATA_START_EMPTY |
| bool "Handle zero length L2CAP start frame" |
| default y if BT_HCI_RAW |
| help |
| Handle zero length L2CAP start frame. |
| |
| config BT_CTLR_RX_ENQUEUE_HOLD |
| bool "Procedure Complete after on-air instant" |
| depends on BT_LL_SW_LLCP_LEGACY |
| default y if BT_HCI_RAW |
| help |
| Hold enqueue of Procedure Complete events with instant until after the |
| on-air instant is reached. |
| |
| config BT_CTLR_TX_RETRY_DISABLE |
| bool "Disable Tx Retry" |
| help |
| Avoid retransmission of a PDU if peer device Nack-ed a transmission |
| in the current connection event, close the connection event so as to |
| save current consumption on retries (in case peer has no buffers to |
| receive new PDUs). |
| |
| Enabling this will lower power consumption, but increase transmission |
| latencies by one connection interval as the next attempt to send a PDU |
| would happen in the next connection event instead of repeated retries |
| in the current connection event. |
| |
| config BT_CTLR_THROUGHPUT |
| bool "Measure incoming Tx throughput" |
| help |
| Measure incoming Tx throughput and log the results. |
| |
| config BT_CTLR_FORCE_MD_COUNT |
| int "Forced MD bit count" if !BT_CTLR_FORCE_MD_AUTO |
| depends on !BT_CTLR_LOW_LAT_ULL |
| range 0 255 |
| default 1 if BT_CTLR_FORCE_MD_AUTO |
| default 0 |
| help |
| No. of times to force MD bit to be set in Tx PDU after a successful |
| transmission of non-empty PDU. |
| |
| This will prolong the connection event to from being closed in cases |
| where applications want to send data in same connection event but are |
| slow in providing new Tx data. |
| |
| config BT_CTLR_FORCE_MD_AUTO |
| bool "Forced MD bit automatic calculation" |
| depends on !BT_CTLR_LOW_LAT_ULL |
| select BT_CTLR_THROUGHPUT |
| default y if BT_HCI_RAW |
| help |
| Force MD bit in transmitted PDU based on runtime incoming transmit |
| data throughput. |
| |
| config BT_CTLR_CONN_RANDOM_FORCE |
| bool "Random forced scheduling for peripheral on missed anchor point" |
| depends on BT_PERIPHERAL |
| default y |
| help |
| When enabled, controller will have legacy behavior and randomly force |
| priority at next ticker scheduling for peripheral role, if anchor point is |
| missed. |
| Two or more connections with similar interval on a device connected |
| to a peer device having two or more connections at its end with same |
| interval could lock to a round robin pattern where in neither of the central |
| nor peripheral event would be in sync at either end. Randomness allows |
| to break this locked round robin pattern permitting an anchor point sync. |
| |
| config BT_CTLR_CONN_RSSI_EVENT |
| bool "Connection RSSI event" |
| depends on BT_CTLR_CONN_RSSI |
| help |
| Generate events for connection RSSI measurement. |
| |
| config BT_CTLR_ALLOW_SAME_PEER_CONN |
| bool "Allow connection requests from same peer" |
| depends on BT_MAX_CONN > 1 |
| help |
| Allow connection requests from the same peer. While the |
| Bluetooth specification does not allow multiple connections |
| with the same peer, allowing such connections is useful |
| while debugging multiple connections. |
| |
| WARNING: This option enables behavior that violates the Bluetooth |
| specification. |
| |
| endif # BT_CONN |
| |
| config BT_CTLR_ADV_INDICATION |
| bool "Advertisement indications" |
| depends on BT_BROADCASTER |
| help |
| Generate events indicating on air advertisement events. |
| |
| config BT_CTLR_SCAN_REQ_NOTIFY |
| bool "Scan Request Notifications" |
| depends on BT_BROADCASTER |
| help |
| Generate events notifying the on air scan requests received. |
| |
| config BT_CTLR_SCAN_REQ_RSSI |
| bool "Measure Scan Request RSSI" |
| depends on BT_CTLR_SCAN_REQ_NOTIFY |
| help |
| Measure RSSI of the on air scan requests received. |
| |
| config BT_CTLR_SCAN_INDICATION |
| bool "Scanner indications" |
| depends on BT_OBSERVER |
| help |
| Generate events indicating on air scanner events. |
| |
| config BT_CTLR_SCAN_UNRESERVED |
| bool "Unreserved scan window" |
| depends on BT_OBSERVER && !BT_CTLR_LOW_LAT |
| default y if BT_MESH |
| help |
| Scanner will not use time space reservation for scan window when in |
| continuous scan mode. |
| |
| config BT_MAYFLY_YIELD_AFTER_CALL |
| bool "Yield from mayfly thread after first call" |
| default y |
| help |
| Only process one mayfly callback per invocation (legacy behavior). |
| If set to 'n', all pending mayflies for callee are executed before |
| yielding |
| |
| config BT_TICKER_LOW_LAT |
| bool "Ticker low latency mode" |
| default y if SOC_SERIES_NRF51X |
| help |
| This option enables legacy ticker scheduling which defers overlapping |
| ticker node timeouts and thereby prevents ticker interrupts during |
| radio RX/TX. Enabling this option disables the ticker priority- and |
| 'must expire' features. |
| |
| config BT_TICKER_UPDATE |
| bool "Ticker Update" |
| help |
| This option enables Ticker Update interface. |
| |
| config BT_TICKER_JOB_IDLE_GET |
| bool "Ticker Job Idle Get" |
| default y if BT_TICKER_LOW_LAT |
| help |
| This option enables the ticker interface to query the idle state of |
| the Ticker Job execution context. This interface is used to disable |
| Ticker Job execution once in idle state, no operations pending for the |
| Ticker Job to process. |
| |
| config BT_TICKER_NEXT_SLOT_GET |
| bool "Ticker Next Slot Get" |
| default y if BT_CENTRAL |
| help |
| This option enables ticker interface to iterate through active |
| ticker nodes, returning tick to expire. |
| |
| config BT_TICKER_REMAINDER_GET |
| bool "Ticker Next Slot Get with Remainder" |
| depends on BT_TICKER_NEXT_SLOT_GET |
| help |
| This option enables ticker interface to iterate through active |
| ticker nodes, returning tick to expire and remainder from a reference |
| tick. |
| |
| config BT_TICKER_LAZY_GET |
| bool "Ticker Next Slot Get with Lazy" |
| depends on BT_TICKER_NEXT_SLOT_GET |
| help |
| This option enables ticker interface to iterate through active |
| ticker nodes, returning tick to expire and lazy count from a reference |
| tick. |
| |
| config BT_TICKER_NEXT_SLOT_GET_MATCH |
| bool "Ticker Next Slot Get with match callback" |
| depends on BT_TICKER_NEXT_SLOT_GET |
| default y if BT_TICKER_SLOT_AGNOSTIC |
| help |
| This option enables ticker interface to iterate through active |
| ticker nodes with a callback for every found ticker node. When |
| returning true in the callback, iteration will stop and the normal |
| operation callback invoked. |
| |
| config BT_TICKER_EXT |
| bool "Ticker extensions" |
| depends on !BT_TICKER_LOW_LAT && !BT_TICKER_SLOT_AGNOSTIC |
| default y if BT_BROADCASTER |
| help |
| This option enables ticker extensions such as re-scheduling of |
| ticker nodes with slot_window set to non-zero. Ticker extensions |
| are invoked by using available '_ext' versions of ticker interface |
| functions. |
| |
| config BT_TICKER_EXT_SLOT_WINDOW_YIELD |
| bool "Tickers with slot window always yields" |
| depends on BT_TICKER_EXT |
| default y if BT_CTLR_ADV_ISO |
| help |
| This options forces tickers with slot window extensions to yield to |
| normal tickers and be placed at the end of their slot window. |
| |
| config BT_TICKER_PRIORITY_SET |
| bool "Tickers with priority based collision resolution" |
| depends on BT_TICKER_EXT |
| help |
| This option provide tickers with persistent priority value that will |
| be used in resolving collisions. |
| |
| The priority feature if enabled then a custom ULL is needed by vendors |
| to avoid repeated skipping of overlapping events as next_has_priority |
| check uses lazy value that would be always lazy_next > lazy_current as |
| currently skipped event becomes the next event with lazy value |
| incremented by 1. This repeated skip happens when all the time |
| between the event intervals are occupied continuously by overlapping |
| tickers. |
| |
| config BT_TICKER_SLOT_AGNOSTIC |
| bool "Slot agnostic ticker mode" |
| help |
| This option enables slot agnostic ticker mode, which ignores slot |
| reservations and collision handling, and operates as a simple |
| multi-instance programmable timer. |
| |
| config BT_CTLR_JIT_SCHEDULING |
| bool "Just-in-Time Scheduling" |
| select BT_TICKER_SLOT_AGNOSTIC |
| help |
| This option enables the experimental 'Next Generation' scheduling |
| feature, which eliminates priorities and collision resolving in the |
| ticker, and instead relies on just-in-time ("lazy") resolution in |
| the link layer. |
| |
| config BT_CTLR_PERIPHERAL_ISO_EARLY_CIG_START |
| bool "Early start of peripheral CIG event" |
| depends on BT_CTLR_PERIPHERAL_ISO |
| help |
| Start scheduling the Peripheral ISO CIG events one event in advance |
| and hence adjust CIG offset and reference point ahead one interval. |
| |
| config BT_CTLR_USER_EXT |
| prompt "Proprietary extensions in Controller" |
| bool |
| help |
| Catch-all for enabling proprietary event types in Controller behavior. |
| |
| config BT_CTLR_USER_EVT_RANGE |
| int "Range of event constants reserved for proprietary event types" |
| depends on BT_CTLR_USER_EXT |
| default 5 |
| range 0 10 |
| help |
| Number of event types reserved for proprietary use. The range |
| is typically used when BT_CTLR_USER_EXT is in use. |
| |
| config BT_CTLR_USER_TICKER_ID_RANGE |
| int "Range of ticker id constants reserved for proprietary ticker nodes" |
| depends on BT_CTLR_USER_EXT |
| default 0 |
| range 0 10 |
| help |
| Number of ticker ids reserved for proprietary use. The range |
| is typically used when BT_CTLR_USER_EXT is in use. |
| |
| config BT_RX_USER_PDU_LEN |
| int "Maximum supported proprietary PDU buffer length" |
| depends on BT_CTLR_USER_EXT |
| default 2 |
| range 2 255 |
| help |
| Maximum data size for each proprietary PDU. This size includes link layer |
| header and payload. It does not account for HCI event headers as these |
| PDUs are assumed to not go across HCI. |
| |
| config BT_CTLR_USER_CPR_INTERVAL_MIN |
| bool "Proprietary Connection Parameter Request minimum interval" |
| depends on BT_CTLR_USER_EXT |
| help |
| When enabled, controller will accept Connection Parameter Request |
| intervals down to a proprietary minimum value. |
| |
| config BT_CTLR_USER_CPR_ANCHOR_POINT_MOVE |
| bool "Proprietary handling of anchor point movement" |
| depends on BT_CTLR_USER_EXT && BT_CTLR_CONN_PARAM_REQ && BT_PERIPHERAL |
| help |
| When enabled, defer accept/reject of Connection Parameter Request with only |
| anchor point movement to proprietary logic. |
| Only applicable for peripheral. |
| |
| endmenu |
| |
| comment "BLE Controller debug configuration" |
| |
| config BT_CTLR_PROFILE_ISR |
| bool "Profile radio ISR" |
| help |
| Turn on measurement of radio ISR latency, CPU usage and generation of |
| controller event with these profiling data. The controller event |
| contains current, minimum and maximum ISR entry latencies; and |
| current, minimum and maximum ISR CPU use in micro-seconds. |
| |
| config BT_CTLR_DEBUG_PINS |
| bool "Bluetooth Controller Debug Pins" |
| depends on BOARD_NRF51DK_NRF51422 || BOARD_NRF52DK_NRF52832 || BOARD_NRF52DK_NRF52810 || BOARD_NRF52840DK_NRF52840 || BOARD_NRF52833DK_NRF52833 || BOARD_NRF5340DK_NRF5340_CPUNET || BOARD_RV32M1_VEGA |
| help |
| Turn on debug GPIO toggling for the BLE Controller. This is useful |
| when debugging with a logic analyzer or profiling certain sections of |
| the code. |
| |
| endif # BT_LL_SW_SPLIT |
