| /* |
| * Copyright (c) 2020 Guillaume Paquet <guillaume.paquet@smile.fr> |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /dts-v1/; |
| #include <nordic/nrf52840_qiaa.dtsi> |
| |
| / { |
| model = "RAKWireless RAK5010 Wistrio Board with a Nordic NRF52840 SoC"; |
| compatible = "nordic,rak5010_nrf52840"; |
| |
| chosen { |
| zephyr,console = &uart1; |
| zephyr,shell-uart = &uart1; |
| zephyr,uart-mcumgr = &uart1; |
| zephyr,bt-mon-uart = &uart1; |
| zephyr,bt-c2h-uart = &uart1; |
| zephyr,sram = &sram0; |
| zephyr,flash = &flash0; |
| zephyr,code-partition = &slot0_partition; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| led0: led_0 { |
| gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
| label = "Green LED 0"; |
| }; |
| }; |
| |
| /* Declaration of aliases */ |
| aliases { |
| led0 = &led0; |
| }; |
| }; |
| |
| &adc { |
| status = "okay"; |
| }; |
| |
| &gpiote { |
| status = "okay"; |
| }; |
| |
| &gpio0 { |
| status = "okay"; |
| }; |
| |
| &gpio1 { |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| compatible = "nordic,nrf-uart"; |
| status = "okay"; |
| current-speed = <115200>; |
| tx-pin = <6>; |
| rx-pin = <8>; |
| rts-pin = <7>; |
| cts-pin = <11>; |
| |
| /* QUECTEL BG9X */ |
| quectel_bg9x: quectel_bg9x { |
| compatible = "quectel,bg9x"; |
| label = "quectel,bg9x"; |
| mdm-power-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
| mdm-reset-gpios = <&gpio0 28 GPIO_ACTIVE_LOW>; |
| mdm-dtr-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; |
| mdm-wdisable-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| }; |
| |
| &uart1 { |
| current-speed = <115200>; |
| status = "okay"; |
| tx-pin = <33>; |
| rx-pin = <34>; |
| }; |
| |
| &i2c1 { |
| compatible = "nordic,nrf-twi"; |
| status = "okay"; |
| sda-pin = <14>; |
| scl-pin = <13>; |
| |
| /* TI OPT3001 light sensor */ |
| opt3001@44 { |
| compatible = "ti,opt3001"; |
| label = "OPT3001"; |
| reg = <0x44>; |
| }; |
| |
| /* ST Microelectronics LIS3DH motion sensor */ |
| lis3dh@19 { |
| compatible = "st,lis3dh"; |
| label = "LIS3DH"; |
| reg = <0x19>; |
| irq-gpios = <&gpio0 15 0>; |
| }; |
| |
| /* ST Microelectronics LPS22HB pressure sensor */ |
| lps22hb-press@5c { |
| compatible = "st,lps22hb-press"; |
| reg = <0x5c>; |
| label = "LPS22HB"; |
| }; |
| }; |
| |
| &qspi { |
| status = "okay"; |
| sck-pin = <43>; |
| io-pins = <47>, <46>, <45>, <44>; |
| csn-pins = <42>; |
| is25wp064a: is25wp064a@0 { |
| compatible = "nordic,qspi-nor"; |
| reg = <0>; |
| writeoc = "pp4io"; |
| readoc = "read4io"; |
| sck-frequency = <16000000>; |
| label = "IS25WP064A"; |
| jedec-id = [9d 70 17]; |
| size = <67108864>; |
| has-dpd; |
| t-enter-dpd = <3000>; |
| t-exit-dpd = <5000>; |
| }; |
| }; |
| |
| &flash0 { |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x000000000 0x0000C000>; |
| }; |
| slot0_partition: partition@c000 { |
| label = "image-0"; |
| reg = <0x0000C000 0x00067000>; |
| }; |
| slot1_partition: partition@73000 { |
| label = "image-1"; |
| reg = <0x00073000 0x00067000>; |
| }; |
| scratch_partition: partition@da000 { |
| label = "image-scratch"; |
| reg = <0x000da000 0x0001e000>; |
| }; |
| |
| /* |
| * The flash starting at 0x000f8000 and ending at |
| * 0x000fffff is reserved for use by the application. |
| */ |
| |
| /* |
| * Storage partition will be used by FCB/LittleFS/NVS |
| * if enabled. |
| */ |
| storage_partition: partition@f8000 { |
| label = "storage"; |
| reg = <0x000f8000 0x00008000>; |
| }; |
| }; |
| }; |
| |
| zephyr_udc0: &usbd { |
| compatible = "nordic,nrf-usbd"; |
| status = "okay"; |
| }; |