| /* |
| * Copyright (c) 2017 Arthur Sfez |
| * |
| * Based on stm32l496g_disco: |
| * |
| * Copyright (c) 2017 Linaro Limited |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /dts-v1/; |
| #include <st/l4/stm32l476Xg.dtsi> |
| #include <st/l4/stm32l476v(c-e-g)tx-pinctrl.dtsi> |
| |
| / { |
| model = "STMicroelectronics STM32L476G-DISCO board"; |
| compatible = "st,stm32l476g-disco"; |
| |
| chosen { |
| zephyr,console = &usart2; |
| zephyr,shell-uart = &usart2; |
| zephyr,sram = &sram0; |
| zephyr,flash = &flash0; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| green_led_4: led_4 { |
| gpios = <&gpiob 2 GPIO_ACTIVE_HIGH>; |
| label = "User LD4"; |
| }; |
| green_led_5: led_5 { |
| gpios = <&gpioe 8 GPIO_ACTIVE_HIGH>; |
| label = "User LD5"; |
| }; |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| joy_center: joystick_center { |
| label = "joystick center"; |
| gpios = <&gpioa 0 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; |
| }; |
| joy_down: joystick_down { |
| label = "joystick down"; |
| gpios = <&gpioa 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; |
| }; |
| joy_up: joystick_up { |
| label = "joystick up"; |
| gpios = <&gpioa 3 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; |
| }; |
| joy_left: joystick_left { |
| label = "joystick left"; |
| gpios = <&gpioa 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; |
| }; |
| joy_right: joystick_right { |
| label = "joystick right"; |
| gpios = <&gpioa 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; |
| }; |
| }; |
| |
| aliases { |
| led0 = &green_led_4; |
| sw0 = &joy_center; |
| }; |
| }; |
| |
| &clk_lsi { |
| status = "okay"; |
| }; |
| |
| &clk_hsi { |
| status = "okay"; |
| }; |
| |
| &pll { |
| div-m = <1>; |
| mul-n = <20>; |
| div-p = <7>; |
| div-q = <2>; |
| div-r = <4>; |
| clocks = <&clk_hsi>; |
| status = "okay"; |
| }; |
| |
| &rcc { |
| clocks = <&pll>; |
| clock-frequency = <DT_FREQ_M(80)>; |
| ahb-prescaler = <1>; |
| apb1-prescaler = <1>; |
| apb2-prescaler = <1>; |
| }; |
| |
| &usart2 { |
| pinctrl-0 = <&usart2_tx_pd5 &usart2_rx_pd6>; |
| pinctrl-names = "default"; |
| current-speed = <115200>; |
| status = "okay"; |
| }; |
| |
| &rtc { |
| clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>, |
| <&rcc STM32_SRC_LSI RTC_SEL(2)>; |
| status = "okay"; |
| |
| backup_regs { |
| status = "okay"; |
| }; |
| }; |