| # Nordic Semiconductor nRF53 MCU line |
| |
| # Copyright (c) 2019 Nordic Semiconductor ASA |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| if SOC_SERIES_NRF53X |
| config SOC_NRF5340_CPUAPP |
| bool |
| select CPU_HAS_NRF_IDAU |
| select CPU_HAS_FPU |
| select ARMV8_M_DSP |
| select HAS_POWEROFF |
| select SOC_COMPATIBLE_NRF5340_CPUAPP |
| imply SOC_NRF53_RTC_PRETICK |
| |
| config SOC_NRF5340_CPUNET |
| bool |
| select ARM_ON_EXIT_CPU_IDLE |
| select SOC_COMPATIBLE_NRF5340_CPUNET |
| imply SOC_NRF53_ANOMALY_160_WORKAROUND_NEEDED |
| imply SOC_NRF53_RTC_PRETICK if !WDT_NRFX |
| |
| choice |
| prompt "nRF53x MCU Selection" |
| |
| config SOC_NRF5340_CPUAPP_QKAA |
| bool "NRF5340_CPUAPP_QKAA" |
| select SOC_NRF5340_CPUAPP |
| |
| config SOC_NRF5340_CPUNET_QKAA |
| bool "NRF5340_CPUNET_QKAA" |
| select SOC_NRF5340_CPUNET |
| |
| endchoice |
| |
| config SOC_NRF53_ANOMALY_160_WORKAROUND_NEEDED |
| bool "Workaround for nRF5340 anomaly 160" |
| imply SOC_NRF53_ANOMALY_160_WORKAROUND |
| help |
| Indicates that the workaround for the anomaly 160 that affects |
| the nRF5340 SoC should be applied. |
| This option is enabled by default for the Application MCU when |
| DC/DC mode is enabled for the VREGMAIN or VREGRADIO regulator |
| and always for the Network MCU. |
| If this option is enabled, but the workaround cannot be applied, |
| because the system clock is disabled, a related cmake warning is |
| issued. |
| |
| config SOC_NRF53_ANOMALY_160_WORKAROUND |
| bool |
| depends on SYS_CLOCK_EXISTS |
| select ARM_ON_ENTER_CPU_IDLE_HOOK |
| |
| config SOC_NRF53_RTC_PRETICK |
| bool "Pre-tick workaround for nRF5340 anomaly 165" |
| depends on (SYS_CLOCK_EXISTS && SOC_NRF5340_CPUNET) || SOC_NRF5340_CPUAPP |
| select NRFX_DPPI |
| select ARM_ON_ENTER_CPU_IDLE_HOOK if SOC_NRF5340_CPUNET |
| select ARM_ON_ENTER_CPU_IDLE_PREPARE_HOOK if SOC_NRF5340_CPUNET |
| help |
| Indicates that the pre-tick workaround for the anomaly 165 that affects |
| the nRF5340 SoC should be applied. The workaround applies to wake ups caused |
| by EVENTS_COMPARE and EVENTS_OVRFLW on RTC0 and RTC1 for which interrupts are |
| enabled through INTENSET register. The case when these events are generated |
| by EVTEN but without interrupts enabled through INTENSET is not handled. |
| The EVENTS_TICK event is not handled. |
| |
| if SOC_NRF53_RTC_PRETICK |
| |
| config SOC_NRF53_RTC_PRETICK_IPC_CH_FROM_NET |
| int "IPC 0 channel for RTC pretick" |
| range 0 15 |
| default 10 |
| |
| config SOC_NRF53_RTC_PRETICK_IPC_CH_TO_NET |
| int "IPC 1 channel for RTC pretick" |
| range 0 15 |
| default 11 |
| |
| endif |
| |
| if SOC_NRF5340_CPUAPP |
| |
| config SOC_DCDC_NRF53X_APP |
| bool |
| imply SOC_NRF53_ANOMALY_160_WORKAROUND_NEEDED |
| help |
| Enable nRF53 series System on Chip Application MCU DC/DC converter. |
| |
| config SOC_DCDC_NRF53X_NET |
| bool |
| imply SOC_NRF53_ANOMALY_160_WORKAROUND_NEEDED |
| help |
| Enable nRF53 series System on Chip Network MCU DC/DC converter. |
| |
| config SOC_DCDC_NRF53X_HV |
| bool |
| help |
| Enable nRF53 series System on Chip High Voltage DC/DC converter. |
| |
| config SOC_NRF_GPIO_FORWARDER_FOR_NRF5340 |
| bool |
| depends on NRF_SOC_SECURE_SUPPORTED |
| help |
| hidden option for including the nRF GPIO pin forwarding |
| |
| if !TRUSTED_EXECUTION_NONSECURE || BUILD_WITH_TFM |
| |
| config SOC_ENABLE_LFXO |
| bool "LFXO" |
| default y |
| help |
| Enable the low-frequency oscillator (LFXO) functionality on XL1 and |
| XL2 pins. |
| This option must be enabled if either application or network core is |
| to use the LFXO. Otherwise, XL1 and XL2 pins will behave as regular |
| GPIOs. |
| |
| choice SOC_LFXO_LOAD_CAPACITANCE |
| prompt "LFXO load capacitance" |
| depends on SOC_ENABLE_LFXO |
| default SOC_LFXO_CAP_INT_7PF |
| |
| config SOC_LFXO_CAP_EXTERNAL |
| bool "Use external load capacitors" |
| |
| config SOC_LFXO_CAP_INT_6PF |
| bool "6 pF internal load capacitance" |
| |
| config SOC_LFXO_CAP_INT_7PF |
| bool "7 pF internal load capacitance" |
| |
| config SOC_LFXO_CAP_INT_9PF |
| bool "9 pF internal load capacitance" |
| |
| endchoice |
| |
| choice SOC_HFXO_LOAD_CAPACITANCE |
| prompt "HFXO load capacitance" |
| default SOC_HFXO_CAP_DEFAULT |
| |
| config SOC_HFXO_CAP_DEFAULT |
| bool "SoC default" |
| help |
| When this option is used, the SoC initialization routine does not |
| touch the XOSC32MCAPS register value, so the default setting for |
| the SoC is in effect. Please note that this may not necessarily be |
| the reset value (0) for the register, as the register can be set |
| during the device trimming in the SystemInit() function. |
| |
| config SOC_HFXO_CAP_EXTERNAL |
| bool "Use external load capacitors" |
| |
| config SOC_HFXO_CAP_INTERNAL |
| bool "Use internal load capacitors" |
| depends on NRF_SOC_SECURE_SUPPORTED |
| |
| endchoice |
| |
| config SOC_HFXO_CAP_INT_VALUE_X2 |
| int "Doubled value of HFXO internal load capacitors (in pF)" |
| depends on SOC_HFXO_CAP_INTERNAL |
| range 14 40 |
| help |
| Internal capacitors ranging from 7.0 pF to 20.0 pF in 0.5 pF steps |
| can be enabled on pins XC1 and XC2. This option specifies doubled |
| capacitance value for the two capacitors. Set it to 14 to get 7.0 pF |
| for each capacitor, 15 to get 7.5 pF, and so on. |
| |
| endif # !TRUSTED_EXECUTION_NONSECURE || BUILD_WITH_TFM |
| |
| endif # SOC_NRF5340_CPUAPP |
| |
| |
| config NRF_ENABLE_CACHE |
| bool "Cache" |
| depends on (SOC_NRF5340_CPUAPP && (!TRUSTED_EXECUTION_NONSECURE || BUILD_WITH_TFM)) \ |
| || SOC_NRF5340_CPUNET |
| default y |
| help |
| Instruction and Data cache is available on nRF5340 CPUAPP |
| (Application MCU). It may only be accessed by Secure code. |
| |
| Instruction cache only (I-Cache) is available in nRF5340 |
| CPUNET (Network MCU). |
| |
| config BUILD_WITH_TFM |
| # TF-M nRF53 platform enables the cache unconditionally. |
| select NRF_ENABLE_CACHE if SOC_NRF5340_CPUAPP |
| |
| config NRF53_SYNC_RTC |
| bool "RTC clock synchronization" |
| default y if LOG && !LOG_MODE_MINIMAL |
| depends on NRF_RTC_TIMER |
| select NRFX_DPPI |
| select MBOX if !IPM |
| |
| if NRF53_SYNC_RTC |
| |
| module = SYNC_RTC |
| module-str = Synchronized RTC |
| source "subsys/logging/Kconfig.template.log_config" |
| |
| config NRF53_SYNC_RTC_INIT_PRIORITY |
| int "nRF53 Synchronized RTC init priority" |
| default APPLICATION_INIT_PRIORITY |
| help |
| nRF53 Synchronized RTC initialization priority. |
| |
| config NRF_RTC_TIMER_USER_CHAN_COUNT |
| default 2 if NRF_802154_RADIO_DRIVER && SOC_NRF5340_CPUNET |
| default 3 if NRF_802154_RADIO_DRIVER |
| default 1 |
| |
| config NRF53_SYNC_RTC_LOG_TIMESTAMP |
| bool "Use Synchronized RTC for logging timestamp" |
| default y |
| |
| config NRF53_SYNC_RTC_IPM_OUT |
| int "IPM channel from APP to NET" |
| range 0 15 |
| default 7 if SOC_NRF5340_CPUAPP |
| default 8 |
| |
| config NRF53_SYNC_RTC_IPM_IN |
| int "IPM channel from APP to NET" |
| range 0 15 |
| default 8 if SOC_NRF5340_CPUAPP |
| default 7 |
| |
| ipm_num = 0 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 1 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 2 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 3 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 4 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 5 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 6 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 7 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 8 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 9 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 10 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 11 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 12 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 13 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 14 |
| rsource "Kconfig.sync_rtc_ipm" |
| ipm_num = 15 |
| rsource "Kconfig.sync_rtc_ipm" |
| |
| endif # NRF53_SYNC_RTC |
| endif # SOC_SERIES_NRF53X |