| /* |
| * Copyright (c) 2018 - 2020 Nordic Semiconductor ASA |
| * Copyright (c) 2018 Ioannis Glaropoulos |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #if defined(CONFIG_SOC_SERIES_NRF51X) || defined(CONFIG_SOC_COMPATIBLE_NRF52X) |
| |
| #include <hal/nrf_ppi.h> |
| |
| static inline void hal_radio_nrf_ppi_channels_enable(uint32_t mask) |
| { |
| nrf_ppi_channels_enable(NRF_PPI, mask); |
| } |
| |
| static inline void hal_radio_nrf_ppi_channels_disable(uint32_t mask) |
| { |
| nrf_ppi_channels_disable(NRF_PPI, mask); |
| } |
| |
| /******************************************************************************* |
| * Enable Radio on Event Timer tick: |
| * wire the EVENT_TIMER EVENTS_COMPARE[0] event to RADIO TASKS_TXEN/RXEN task. |
| * |
| * Use the pre-programmed PPI channels if possible (if TIMER0 is used as the |
| * EVENT_TIMER). |
| */ |
| #if (EVENT_TIMER_ID == 0) |
| |
| /* PPI channel 20 is pre-programmed with the following fixed settings: |
| * EEP: TIMER0->EVENTS_COMPARE[0] |
| * TEP: RADIO->TASKS_TXEN |
| */ |
| #define HAL_RADIO_ENABLE_TX_ON_TICK_PPI 20 |
| /* PPI channel 21 is pre-programmed with the following fixed settings: |
| * EEP: TIMER0->EVENTS_COMPARE[0] |
| * TEP: RADIO->TASKS_RXEN |
| */ |
| #define HAL_RADIO_ENABLE_RX_ON_TICK_PPI 21 |
| |
| static inline void hal_radio_enable_on_tick_ppi_config_and_enable(uint8_t trx) |
| { |
| /* No need to configure anything for the pre-programmed channels. |
| * Just enable and disable them accordingly. |
| */ |
| nrf_ppi_channels_disable( |
| NRF_PPI, |
| trx ? BIT(HAL_RADIO_ENABLE_RX_ON_TICK_PPI) |
| : BIT(HAL_RADIO_ENABLE_TX_ON_TICK_PPI)); |
| nrf_ppi_channels_enable( |
| NRF_PPI, |
| trx ? BIT(HAL_RADIO_ENABLE_TX_ON_TICK_PPI) |
| : BIT(HAL_RADIO_ENABLE_RX_ON_TICK_PPI)); |
| } |
| |
| #else |
| |
| #define HAL_RADIO_ENABLE_ON_TICK_PPI 2 |
| #define HAL_RADIO_ENABLE_TX_ON_TICK_PPI HAL_RADIO_ENABLE_ON_TICK_PPI |
| #define HAL_RADIO_ENABLE_RX_ON_TICK_PPI HAL_RADIO_ENABLE_ON_TICK_PPI |
| |
| static inline void hal_radio_enable_on_tick_ppi_config_and_enable(uint8_t trx) |
| { |
| uint32_t event_address = (trx ? (uint32_t)&(NRF_RADIO->TASKS_TXEN) |
| : (uint32_t)&(NRF_RADIO->TASKS_RXEN)); |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_RADIO_ENABLE_ON_TICK_PPI, |
| (uint32_t)&(EVENT_TIMER->EVENTS_COMPARE[0]), |
| event_address); |
| nrf_ppi_channels_enable(NRF_PPI, BIT(HAL_RADIO_ENABLE_ON_TICK_PPI)); |
| } |
| |
| #endif /* (EVENT_TIMER_ID == 0) */ |
| |
| /******************************************************************************* |
| * Capture event timer on Address reception: |
| * wire the RADIO EVENTS_ADDRESS event to the |
| * EVENT_TIMER TASKS_CAPTURE[<address timer>] task. |
| * |
| * Use the pre-programmed PPI channel if possible (if TIMER0 is used as the |
| * EVENT_TIMER). |
| */ |
| #if (EVENT_TIMER_ID == 0) |
| |
| /* PPI channel 26 is pre-programmed with the following fixed settings: |
| * EEP: RADIO->EVENTS_ADDRESS |
| * TEP: TIMER0->TASKS_CAPTURE[1] |
| */ |
| #define HAL_RADIO_RECV_TIMEOUT_CANCEL_PPI 26 |
| |
| static inline void hal_radio_recv_timeout_cancel_ppi_config(void) |
| { |
| /* No need to configure anything for the pre-programmed channel. */ |
| } |
| |
| #else |
| |
| #define HAL_RADIO_RECV_TIMEOUT_CANCEL_PPI 3 |
| |
| static inline void hal_radio_recv_timeout_cancel_ppi_config(void) |
| { |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_RADIO_RECV_TIMEOUT_CANCEL_PPI, |
| (uint32_t)&(NRF_RADIO->EVENTS_ADDRESS), |
| (uint32_t)&(EVENT_TIMER->TASKS_CAPTURE[1])); |
| } |
| |
| #endif /* (EVENT_TIMER_ID == 0) */ |
| |
| /******************************************************************************* |
| * Disable Radio on HCTO: |
| * wire the EVENT_TIMER EVENTS_COMPARE[<HCTO timer>] event |
| * to the RADIO TASKS_DISABLE task. |
| * |
| * Use the pre-programmed PPI channel if possible (if TIMER0 is used as the |
| * EVENT_TIMER). |
| */ |
| #if (EVENT_TIMER_ID == 0) |
| |
| /* PPI channel 22 is pre-programmed with the following fixed settings: |
| * EEP: TIMER0->EVENTS_COMPARE[1] |
| * TEP: RADIO->TASKS_DISABLE |
| */ |
| #define HAL_RADIO_DISABLE_ON_HCTO_PPI 22 |
| |
| static inline void hal_radio_disable_on_hcto_ppi_config(void) |
| { |
| /* No need to configure anything for the pre-programmed channel. */ |
| } |
| |
| #else |
| |
| #define HAL_RADIO_DISABLE_ON_HCTO_PPI 4 |
| |
| static inline void hal_radio_disable_on_hcto_ppi_config(void) |
| { |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_RADIO_DISABLE_ON_HCTO_PPI, |
| (uint32_t)&(EVENT_TIMER->EVENTS_COMPARE[1]), |
| (uint32_t)&(NRF_RADIO->TASKS_DISABLE)); |
| } |
| |
| #endif /* (EVENT_TIMER_ID == 0) */ |
| |
| /******************************************************************************* |
| * Capture event timer on Radio end: |
| * wire the RADIO EVENTS_END event to the |
| * EVENT_TIMER TASKS_CAPTURE[<radio end timer>] task. |
| * |
| * Use the pre-programmed PPI channel if possible (if TIMER0 is used as the |
| * EVENT_TIMER). |
| */ |
| #if (EVENT_TIMER_ID == 0) |
| |
| /* PPI channel 27 is pre-programmed with the following fixed settings: |
| * EEP: RADIO->EVENTS_END |
| * TEP: TIMER0->TASKS_CAPTURE[2] |
| */ |
| #define HAL_RADIO_END_TIME_CAPTURE_PPI 27 |
| |
| static inline void hal_radio_end_time_capture_ppi_config(void) |
| { |
| /* No need to configure anything for the pre-programmed channel. */ |
| } |
| |
| #else |
| |
| #define HAL_RADIO_END_TIME_CAPTURE_PPI 5 |
| |
| static inline void hal_radio_end_time_capture_ppi_config(void) |
| { |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_RADIO_END_TIME_CAPTURE_PPI, |
| (uint32_t)&(NRF_RADIO->EVENTS_END), |
| (uint32_t)&(EVENT_TIMER->TASKS_CAPTURE[2])); |
| } |
| |
| #endif /* (EVENT_TIMER_ID == 0) */ |
| |
| /******************************************************************************* |
| * Start event timer on RTC tick: |
| * wire the RTC0 EVENTS_COMPARE[2] event to EVENT_TIMER TASKS_START task. |
| */ |
| #define HAL_EVENT_TIMER_START_PPI 6 |
| |
| static inline void hal_event_timer_start_ppi_config(void) |
| { |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_EVENT_TIMER_START_PPI, |
| (uint32_t)&(NRF_RTC0->EVENTS_COMPARE[2]), |
| (uint32_t)&(EVENT_TIMER->TASKS_START)); |
| } |
| |
| /******************************************************************************* |
| * Capture event timer on Radio ready: |
| * wire the RADIO EVENTS_READY event to the |
| * EVENT_TIMER TASKS_CAPTURE[<radio ready timer>] task. |
| */ |
| #define HAL_RADIO_READY_TIME_CAPTURE_PPI 7 |
| |
| static inline void hal_radio_ready_time_capture_ppi_config(void) |
| { |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_RADIO_READY_TIME_CAPTURE_PPI, |
| (uint32_t)&(NRF_RADIO->EVENTS_READY), |
| (uint32_t)&(EVENT_TIMER->TASKS_CAPTURE[0])); |
| } |
| |
| /******************************************************************************* |
| * Trigger encryption task upon address reception: |
| * wire the RADIO EVENTS_ADDRESS event to the CCM TASKS_CRYPT task. |
| * |
| * PPI channel 25 is pre-programmed with the following fixed settings: |
| * EEP: RADIO->EVENTS_ADDRESS |
| * TEP: CCM->TASKS_CRYPT |
| */ |
| #define HAL_TRIGGER_CRYPT_PPI 25 |
| |
| static inline void hal_trigger_crypt_ppi_config(void) |
| { |
| /* No need to configure anything for the pre-programmed channel. */ |
| } |
| |
| /******************************************************************************* |
| * Trigger automatic address resolution on Bit counter match: |
| * wire the RADIO EVENTS_BCMATCH event to the AAR TASKS_START task. |
| * |
| * PPI channel 23 is pre-programmed with the following fixed settings: |
| * EEP: RADIO->EVENTS_BCMATCH |
| * TEP: AAR->TASKS_START |
| */ |
| #define HAL_TRIGGER_AAR_PPI 23 |
| |
| static inline void hal_trigger_aar_ppi_config(void) |
| { |
| /* No need to configure anything for the pre-programmed channel. */ |
| } |
| |
| /******************************************************************************* |
| * Trigger Radio Rate override upon Rateboost event. |
| */ |
| #if defined(CONFIG_HAS_HW_NRF_RADIO_BLE_CODED) |
| |
| #define HAL_TRIGGER_RATEOVERRIDE_PPI 14 |
| |
| static inline void hal_trigger_rateoverride_ppi_config(void) |
| { |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_TRIGGER_RATEOVERRIDE_PPI, |
| (uint32_t)&(NRF_RADIO->EVENTS_RATEBOOST), |
| (uint32_t)&(NRF_CCM->TASKS_RATEOVERRIDE)); |
| } |
| |
| #endif /* CONFIG_HAS_HW_NRF_RADIO_BLE_CODED */ |
| |
| /******************************************************************************/ |
| #if defined(CONFIG_BT_CTLR_GPIO_PA_PIN) || defined(CONFIG_BT_CTLR_GPIO_LNA_PIN) |
| |
| #define HAL_ENABLE_PALNA_PPI 15 |
| #define HAL_DISABLE_PALNA_PPI 16 |
| |
| static inline void hal_palna_ppi_setup(void) |
| { |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_ENABLE_PALNA_PPI, |
| (uint32_t)&(EVENT_TIMER->EVENTS_COMPARE[2]), |
| (uint32_t)&(NRF_GPIOTE->TASKS_OUT[ |
| CONFIG_BT_CTLR_PA_LNA_GPIOTE_CHAN])); |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_DISABLE_PALNA_PPI, |
| (uint32_t)&(NRF_RADIO->EVENTS_DISABLED), |
| (uint32_t)&(NRF_GPIOTE->TASKS_OUT[ |
| CONFIG_BT_CTLR_PA_LNA_GPIOTE_CHAN])); |
| } |
| |
| #endif /* CONFIG_BT_CTLR_GPIO_PA_PIN || CONFIG_BT_CTLR_GPIO_LNA_PIN */ |
| |
| /******************************************************************************/ |
| #if defined(CONFIG_BT_CTLR_FEM_NRF21540) |
| static inline void hal_pa_ppi_setup(void) |
| { |
| /* Nothing specific to PA with FEM to handle inside TRX chains */ |
| } |
| |
| static inline void hal_lna_ppi_setup(void) |
| { |
| /* Nothing specific to LNA with FEM to handle inside TRX chains */ |
| } |
| |
| #define HAL_ENABLE_FEM_PPI 4 |
| #define HAL_DISABLE_FEM_PPI 5 |
| |
| static inline void hal_fem_ppi_setup(void) |
| { |
| nrf_ppi_channel_and_fork_endpoint_setup( |
| NRF_PPI, |
| HAL_ENABLE_FEM_PPI, |
| (uint32_t)&(EVENT_TIMER->EVENTS_COMPARE[3]), |
| (uint32_t)&(NRF_GPIOTE->TASKS_OUT[ |
| CONFIG_BT_CTLR_PDN_GPIOTE_CHAN]), |
| (uint32_t)&(NRF_GPIOTE->TASKS_OUT[ |
| CONFIG_BT_CTLR_CSN_GPIOTE_CHAN])); |
| nrf_ppi_channel_and_fork_endpoint_setup( |
| NRF_PPI, |
| HAL_DISABLE_FEM_PPI, |
| (uint32_t)&(NRF_RADIO->EVENTS_DISABLED), |
| (uint32_t)&(NRF_GPIOTE->TASKS_OUT[ |
| CONFIG_BT_CTLR_PDN_GPIOTE_CHAN]), |
| (uint32_t)&(NRF_GPIOTE->TASKS_OUT[ |
| CONFIG_BT_CTLR_CSN_GPIOTE_CHAN])); |
| } |
| |
| #endif /* CONFIG_BT_CTLR_FEM_NRF21540 */ |
| |
| /******************************************************************************/ |
| #if !defined(CONFIG_BT_CTLR_TIFS_HW) |
| /* PPI setup used for SW-based auto-switching during TIFS. */ |
| |
| #if !defined(CONFIG_BT_CTLR_SW_SWITCH_SINGLE_TIMER) |
| |
| /* Clear SW-switch timer on packet end: |
| * wire the RADIO EVENTS_END event to SW_SWITCH_TIMER TASKS_CLEAR task. |
| * |
| * Note: this PPI is not needed if we use a single TIMER instance in radio.c |
| */ |
| #define HAL_SW_SWITCH_TIMER_CLEAR_PPI 8 |
| |
| static inline void hal_sw_switch_timer_clear_ppi_config(void) |
| { |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_SW_SWITCH_TIMER_CLEAR_PPI, |
| (uint32_t)&(NRF_RADIO->EVENTS_END), |
| (uint32_t)&(SW_SWITCH_TIMER->TASKS_CLEAR)); |
| } |
| |
| #else /* !CONFIG_BT_CTLR_SW_SWITCH_SINGLE_TIMER */ |
| |
| /* Clear event timer (sw-switch timer) on Radio end: |
| * wire the RADIO EVENTS_END event to the |
| * EVENT_TIMER TASKS_CLEAR task. |
| * |
| * Note: in nRF52X this PPI channel is forked for both capturing and clearing |
| * timer on RADIO EVENTS_END. |
| */ |
| #define HAL_SW_SWITCH_TIMER_CLEAR_PPI HAL_RADIO_END_TIME_CAPTURE_PPI |
| |
| static inline void hal_sw_switch_timer_clear_ppi_config(void) |
| { |
| nrf_ppi_fork_endpoint_setup( |
| NRF_PPI, |
| HAL_RADIO_END_TIME_CAPTURE_PPI, |
| (uint32_t)&(SW_SWITCH_TIMER->TASKS_CLEAR)); |
| } |
| |
| #endif /* !CONFIG_BT_CTLR_SW_SWITCH_SINGLE_TIMER */ |
| |
| /* The 2 adjacent PPI groups used for implementing SW_SWITCH_TIMER-based |
| * auto-switch for TIFS. 'index' must be 0 or 1. |
| */ |
| #define SW_SWITCH_TIMER_TASK_GROUP(index) \ |
| (SW_SWITCH_TIMER_TASK_GROUP_BASE + (index)) |
| |
| /* The 2 adjacent TIMER EVENTS_COMPARE event offsets used for implementing |
| * SW_SWITCH_TIMER-based auto-switch for TIFS. 'index' must be 0 or 1. |
| */ |
| #define SW_SWITCH_TIMER_EVTS_COMP(index) \ |
| (SW_SWITCH_TIMER_EVTS_COMP_BASE + (index)) |
| |
| /* Wire a SW SWITCH TIMER EVENTS_COMPARE[<cc_offset>] event |
| * to a PPI GROUP TASK DISABLE task (PPI group with index <index>). |
| * 2 adjacent PPIs (9 & 10) and 2 adjacent PPI groups are used for this wiring; |
| * <index> must be 0 or 1. <offset> must be a valid TIMER CC register offset. |
| */ |
| #if defined(CONFIG_SOC_NRF52805) |
| /* Because nRF52805 has limited number of programmable PPI channels, |
| * tIFS Trx SW switching on this SoC can be used only when pre-programmed |
| * PPI channels are also in use, i.e. when TIMER0 is the event timer. |
| */ |
| #if (EVENT_TIMER_ID == 0) |
| #define HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_BASE 2 |
| #else |
| #error "tIFS Trx SW switch can be used on this SoC only with TIMER0 as the event timer" |
| #endif |
| #else /* -> !defined(CONFIG_SOC_NRF52805) */ |
| #define HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_BASE 9 |
| #endif |
| #define HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI(index) \ |
| (HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_BASE + (index)) |
| #define HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_REGISTER_EVT(chan) \ |
| NRF_PPI->CH[chan].EEP |
| #define HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_EVT(cc_offset) \ |
| ((uint32_t)&(SW_SWITCH_TIMER->EVENTS_COMPARE[cc_offset])) |
| #define HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_REGISTER_TASK(chan) \ |
| NRF_PPI->CH[chan].TEP |
| #define HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_TASK(index) \ |
| ((uint32_t)&(NRF_PPI->TASKS_CHG[SW_SWITCH_TIMER_TASK_GROUP(index)].DIS)) |
| |
| /* Wire the RADIO EVENTS_END event to one of the PPI GROUP TASK ENABLE task. |
| * 2 adjacent PPI groups are used for this wiring. 'index' must be 0 or 1. |
| */ |
| #if defined(CONFIG_SOC_NRF52805) |
| #if (EVENT_TIMER_ID == 0) |
| #define HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI 9 |
| #else |
| #error "tIFS Trx SW switch can be used on this SoC only with TIMER0 as the event timer" |
| #endif |
| #else /* -> !defined(CONFIG_SOC_NRF52805) */ |
| #define HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI 11 |
| #endif |
| #define HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI_EVT \ |
| ((uint32_t)&(NRF_RADIO->EVENTS_END)) |
| #define HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI_TASK(index) \ |
| ((uint32_t)&(NRF_PPI->TASKS_CHG[SW_SWITCH_TIMER_TASK_GROUP(index)].EN)) |
| |
| /*Enable Radio at specific time-stamp: |
| * wire the SW SWITCH TIMER EVENTS_COMPARE[<cc_offset>] event |
| * to RADIO TASKS_TXEN/RXEN task. |
| * 2 adjacent PPIs (12 & 13) are used for this wiring; <index> must be 0 or 1. |
| * <offset> must be a valid TIMER CC register offset. |
| */ |
| #if defined(CONFIG_SOC_NRF52805) |
| #if (EVENT_TIMER_ID == 0) |
| #define HAL_SW_SWITCH_RADIO_ENABLE_PPI_BASE 4 |
| #else |
| #error "tIFS Trx SW switch can be used on this SoC only with TIMER0 as the event timer" |
| #endif |
| #else /* -> !defined(CONFIG_SOC_NRF52805) */ |
| #define HAL_SW_SWITCH_RADIO_ENABLE_PPI_BASE 12 |
| #endif |
| #define HAL_SW_SWITCH_RADIO_ENABLE_PPI(index) \ |
| (HAL_SW_SWITCH_RADIO_ENABLE_PPI_BASE + (index)) |
| #define HAL_SW_SWITCH_RADIO_ENABLE_PPI_REGISTER_EVT(chan) \ |
| NRF_PPI->CH[chan].EEP |
| #define HAL_SW_SWITCH_RADIO_ENABLE_PPI_EVT(cc_offset) \ |
| ((uint32_t)&(SW_SWITCH_TIMER->EVENTS_COMPARE[cc_offset])) |
| #define HAL_SW_SWITCH_RADIO_ENABLE_PPI_REGISTER_TASK(chan) \ |
| NRF_PPI->CH[chan].TEP |
| #define HAL_SW_SWITCH_RADIO_ENABLE_PPI_TASK_TX \ |
| ((uint32_t)&(NRF_RADIO->TASKS_TXEN)) |
| #define HAL_SW_SWITCH_RADIO_ENABLE_PPI_TASK_RX \ |
| ((uint32_t)&(NRF_RADIO->TASKS_RXEN)) |
| |
| static inline void hal_radio_sw_switch_setup( |
| uint8_t compare_reg, |
| uint8_t radio_enable_ppi, |
| uint8_t ppi_group_index) |
| { |
| /* Set up software switch mechanism for next Radio switch. */ |
| |
| /* Wire RADIO END event to PPI Group[<index>] enable task, |
| * over PPI[<HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI>] |
| */ |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI, |
| HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI_EVT, |
| HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI_TASK(ppi_group_index)); |
| |
| /* Wire SW Switch timer event <compare_reg> to the |
| * PPI[<radio_enable_ppi>] for enabling Radio. Do |
| * not wire the task; it is done by the caller of |
| * the function depending on the desired direction |
| * (TX/RX). |
| */ |
| nrf_ppi_event_endpoint_setup( |
| NRF_PPI, |
| radio_enable_ppi, |
| HAL_SW_SWITCH_RADIO_ENABLE_PPI_EVT(compare_reg)); |
| } |
| |
| static inline void hal_radio_txen_on_sw_switch(uint8_t ppi) |
| { |
| nrf_ppi_task_endpoint_setup( |
| NRF_PPI, |
| ppi, |
| HAL_SW_SWITCH_RADIO_ENABLE_PPI_TASK_TX); |
| } |
| |
| static inline void hal_radio_b2b_txen_on_sw_switch(uint8_t ppi) |
| { |
| /* NOTE: As independent PPI are used to trigger the Radio Tx task, |
| * double buffers implementation works for sw_switch using PPIs, |
| * simply reuse the hal_radio_txen_on_sw_switch() functon to set |
| * the next PPIs task to be Radio Tx enable. |
| */ |
| hal_radio_txen_on_sw_switch(ppi); |
| } |
| |
| static inline void hal_radio_rxen_on_sw_switch(uint8_t ppi) |
| { |
| nrf_ppi_task_endpoint_setup( |
| NRF_PPI, |
| ppi, |
| HAL_SW_SWITCH_RADIO_ENABLE_PPI_TASK_RX); |
| } |
| |
| static inline void hal_radio_sw_switch_disable(void) |
| { |
| /* Disable the following PPI channels that implement SW Switch: |
| * - Clearing SW SWITCH TIMER on RADIO END event |
| * - Enabling SW SWITCH PPI Group on RADIO END event |
| */ |
| nrf_ppi_channels_disable( |
| NRF_PPI, |
| BIT(HAL_SW_SWITCH_TIMER_CLEAR_PPI) | |
| BIT(HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI)); |
| } |
| |
| static inline void hal_radio_sw_switch_cleanup(void) |
| { |
| hal_radio_sw_switch_disable(); |
| nrf_ppi_group_disable(NRF_PPI, SW_SWITCH_TIMER_TASK_GROUP(0)); |
| nrf_ppi_group_disable(NRF_PPI, SW_SWITCH_TIMER_TASK_GROUP(1)); |
| } |
| |
| #if defined(CONFIG_BT_CTLR_PHY_CODED) && \ |
| defined(CONFIG_HAS_HW_NRF_RADIO_BLE_CODED) |
| /* The 2 adjacent TIMER EVENTS_COMPARE event offsets used for implementing |
| * SW_SWITCH_TIMER-based auto-switch for TIFS, when receiving in LE Coded PHY. |
| * 'index' must be 0 or 1. |
| */ |
| #define SW_SWITCH_TIMER_S2_EVTS_COMP(index) \ |
| (SW_SWITCH_TIMER_EVTS_COMP_S2_BASE + (index)) |
| |
| /* Wire the SW SWITCH TIMER EVENTS_COMPARE[<cc_offset>] event |
| * to RADIO TASKS_TXEN/RXEN task. |
| */ |
| #define HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI_BASE 17 |
| #define HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI(index) \ |
| (HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI_BASE + (index)) |
| |
| /* Cancel the SW switch timer running considering S8 timing: |
| * wire the RADIO EVENTS_RATEBOOST event to SW_SWITCH_TIMER TASKS_CAPTURE task. |
| */ |
| #define HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI 19 |
| #define HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI_REGISTER_EVT \ |
| NRF_PPI->CH[HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI].EEP |
| #define HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI_EVT \ |
| ((uint32_t)&(NRF_RADIO->EVENTS_RATEBOOST)) |
| #define HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI_REGISTER_TASK \ |
| NRF_PPI->CH[HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI].TEP |
| #define HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI_TASK(index) \ |
| ((uint32_t)&(SW_SWITCH_TIMER->TASKS_CAPTURE[index])) |
| |
| static inline void hal_radio_sw_switch_coded_tx_config_set(uint8_t ppi_en, |
| uint8_t ppi_dis, uint8_t cc_s2, uint8_t group_index) |
| { |
| HAL_SW_SWITCH_RADIO_ENABLE_PPI_REGISTER_EVT(ppi_en) = |
| HAL_SW_SWITCH_RADIO_ENABLE_PPI_EVT(cc_s2); |
| |
| HAL_SW_SWITCH_RADIO_ENABLE_PPI_REGISTER_TASK(ppi_en) = |
| HAL_SW_SWITCH_RADIO_ENABLE_PPI_TASK_TX; |
| |
| /* Wire the Group task disable |
| * to the S2 EVENTS_COMPARE. |
| */ |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_REGISTER_EVT( |
| ppi_dis) = |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_EVT(cc_s2); |
| |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_REGISTER_TASK( |
| ppi_dis) = |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_TASK( |
| group_index); |
| |
| /* Capture CC to cancel the timer that has assumed |
| * S8 reception, if packet will be received in S2. |
| */ |
| HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI_REGISTER_EVT = |
| HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI_EVT; |
| HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI_REGISTER_TASK = |
| HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI_TASK( |
| group_index); |
| |
| nrf_ppi_channels_enable( |
| NRF_PPI, |
| BIT(HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI)); |
| } |
| |
| static inline void hal_radio_sw_switch_coded_config_clear(uint8_t ppi_en, |
| uint8_t ppi_dis, uint8_t cc_reg, uint8_t group_index) |
| { |
| /* Invalidate PPI used when RXing on LE Coded PHY. */ |
| HAL_SW_SWITCH_RADIO_ENABLE_PPI_REGISTER_EVT( |
| ppi_en) = 0; |
| HAL_SW_SWITCH_RADIO_ENABLE_PPI_REGISTER_TASK( |
| ppi_en) = 0; |
| |
| /* Wire the Group task disable to the default EVENTS_COMPARE. */ |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_REGISTER_EVT( |
| ppi_dis) = |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_EVT(cc_reg); |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_REGISTER_TASK( |
| ppi_dis) = |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_TASK( |
| group_index); |
| } |
| |
| #else |
| |
| static inline void hal_radio_group_task_disable_ppi_setup(void) |
| { |
| /* Wire SW SWITCH TIMER EVENTS COMPARE event <cc index-0> to |
| * PPI Group TASK [<index-0>] DISABLE task, over PPI<index-0>. |
| */ |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI(0), |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_EVT( |
| SW_SWITCH_TIMER_EVTS_COMP(0)), |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_TASK(0)); |
| |
| /* Wire SW SWITCH TIMER event <compare index-1> to |
| * PPI Group[<index-1>] Disable Task, over PPI<index-1>. |
| */ |
| nrf_ppi_channel_endpoint_setup( |
| NRF_PPI, |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI(1), |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_EVT( |
| SW_SWITCH_TIMER_EVTS_COMP(1)), |
| HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_TASK(1)); |
| } |
| #endif /* CONFIG_HAS_HW_NRF_RADIO_BLE_CODED */ |
| |
| static inline void hal_radio_sw_switch_ppi_group_setup(void) |
| { |
| /* Include the appropriate PPI channels in the two PPI Groups. */ |
| #if !defined(CONFIG_BT_CTLR_PHY_CODED) || \ |
| !defined(CONFIG_HAS_HW_NRF_RADIO_BLE_CODED) |
| NRF_PPI->CHG[SW_SWITCH_TIMER_TASK_GROUP(0)] = |
| BIT(HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI(0)) | |
| BIT(HAL_SW_SWITCH_RADIO_ENABLE_PPI(0)); |
| NRF_PPI->CHG[SW_SWITCH_TIMER_TASK_GROUP(1)] = |
| BIT(HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI(1)) | |
| BIT(HAL_SW_SWITCH_RADIO_ENABLE_PPI(1)); |
| #else |
| NRF_PPI->CHG[SW_SWITCH_TIMER_TASK_GROUP(0)] = |
| BIT(HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI(0)) | |
| BIT(HAL_SW_SWITCH_RADIO_ENABLE_PPI(0)) | |
| BIT(HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI(0)); |
| NRF_PPI->CHG[SW_SWITCH_TIMER_TASK_GROUP(1)] = |
| BIT(HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI(1)) | |
| BIT(HAL_SW_SWITCH_RADIO_ENABLE_PPI(1)) | |
| BIT(HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI(1)); |
| #endif /* CONFIG_BT_CTLR_PHY_CODED && CONFIG_HAS_HW_NRF_RADIO_BLE_CODED */ |
| } |
| |
| #endif /* !CONFIG_BT_CTLR_TIFS_HW */ |
| #endif /* CONFIG_SOC_SERIES_NRF51X || CONFIG_SOC_COMPATIBLE_NRF52X */ |
| |
| /******************************************************************************/ |
| |
| #define HAL_USED_PPI_CHANNELS \ |
| (BIT(HAL_RADIO_ENABLE_TX_ON_TICK_PPI) | \ |
| BIT(HAL_RADIO_ENABLE_RX_ON_TICK_PPI) | \ |
| BIT(HAL_RADIO_RECV_TIMEOUT_CANCEL_PPI) | \ |
| BIT(HAL_RADIO_DISABLE_ON_HCTO_PPI) | \ |
| BIT(HAL_RADIO_END_TIME_CAPTURE_PPI) | \ |
| BIT(HAL_EVENT_TIMER_START_PPI) | \ |
| BIT(HAL_RADIO_READY_TIME_CAPTURE_PPI) | \ |
| BIT(HAL_TRIGGER_CRYPT_PPI) | \ |
| BIT(HAL_TRIGGER_AAR_PPI) | \ |
| HAL_USED_PPI_CHANNELS_2 | HAL_USED_PPI_CHANNELS_3 | \ |
| HAL_USED_PPI_CHANNELS_4 | HAL_USED_PPI_CHANNELS_5 | \ |
| HAL_USED_PPI_CHANNELS_6) |
| |
| #if defined(HAL_TRIGGER_RATEOVERRIDE_PPI) |
| #define HAL_USED_PPI_CHANNELS_2 \ |
| BIT(HAL_TRIGGER_RATEOVERRIDE_PPI) |
| #else |
| #define HAL_USED_PPI_CHANNELS_2 0 |
| #endif |
| |
| #if defined(HAL_ENABLE_PALNA_PPI) |
| #define HAL_USED_PPI_CHANNELS_3 \ |
| (BIT(HAL_ENABLE_PALNA_PPI) | \ |
| BIT(HAL_DISABLE_PALNA_PPI)) |
| #else |
| #define HAL_USED_PPI_CHANNELS_3 0 |
| #endif |
| |
| #if defined(HAL_SW_SWITCH_TIMER_CLEAR_PPI) |
| #define HAL_USED_PPI_CHANNELS_4 \ |
| (BIT(HAL_SW_SWITCH_TIMER_CLEAR_PPI) | \ |
| BIT(HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_BASE) | \ |
| BIT(HAL_SW_SWITCH_GROUP_TASK_DISABLE_PPI_BASE + 1) | \ |
| BIT(HAL_SW_SWITCH_GROUP_TASK_ENABLE_PPI) | \ |
| BIT(HAL_SW_SWITCH_RADIO_ENABLE_PPI_BASE) | \ |
| BIT(HAL_SW_SWITCH_RADIO_ENABLE_PPI_BASE + 1)) |
| #else |
| #define HAL_USED_PPI_CHANNELS_4 0 |
| #endif |
| |
| #if defined(HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI_BASE) |
| #define HAL_USED_PPI_CHANNELS_5 \ |
| (BIT(HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI_BASE) | \ |
| BIT(HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI_BASE + 1) | \ |
| BIT(HAL_SW_SWITCH_TIMER_S8_DISABLE_PPI)) |
| #else |
| #define HAL_USED_PPI_CHANNELS_5 0 |
| #endif |
| |
| #if defined(HAL_ENABLE_FEM_PPI) |
| #define HAL_USED_PPI_CHANNELS_6 \ |
| (BIT(HAL_ENABLE_FEM_PPI) | \ |
| BIT(HAL_DISABLE_FEM_PPI)) |
| #else |
| #define HAL_USED_PPI_CHANNELS_6 0 |
| #endif |
| |
| BUILD_ASSERT( |
| (HAL_USED_PPI_CHANNELS & NRFX_PPI_CHANNELS_USED_BY_PWM_SW) == 0, |
| "PPI channels used by the Bluetooth controller overlap with those " |
| "assigned to the pwm_nrf5_sw driver."); |
| |
| #if defined(SW_SWITCH_TIMER_TASK_GROUP_BASE) |
| #define HAL_USED_PPI_GROUPS \ |
| (BIT(SW_SWITCH_TIMER_TASK_GROUP_BASE) | \ |
| BIT(SW_SWITCH_TIMER_TASK_GROUP_BASE + 1)) |
| #else |
| #define HAL_USED_PPI_GROUPS 0 |
| #endif |