blob: 9a6e142b94d9e113a920aa2b3c938c4da31cef5d [file] [log] [blame]
# Kconfig - ETH_ENC28J60 Ethernet driver configuration options
#
# Copyright (c) 2015 Intel Corporation
#
# SPDX-License-Identifier: Apache-2.0
#
menuconfig ETH_ENC28J60
bool "ENC28J60C Ethernet Controller"
depends on NET_L2_ETHERNET
depends on SPI
default n
help
ENC28J60C Stand-Alone Ethernet Controller
with SPI Interface
config ETH_ENC28J60_RX_THREAD_STACK_SIZE
int "Stack size for internal incoming packet handler"
depends on ETH_ENC28J60
default 800
help
Size of the stack used for internal thread which is ran for
incoming packet processing.
config ETH_ENC28J60_RX_THREAD_PRIO
int "Priority for internal incoming packet handler"
depends on ETH_ENC28J60
default 2
help
Priority level for internal thread which is ran for incoming
packet processing.
config ETH_EN28J60_TIMEOUT
int "IP buffer timeout"
depends on ETH_ENC28J60
default 100
help
Given timeout in milliseconds. Maximum amount of time
that the driver will wait from the IP stack to get
a memory buffer before the ethernet frame is dropped.
config ETH_ENC28J60_0
bool "ENC28J60C Ethernet port 0"
depends on ETH_ENC28J60
default n
help
Include port 0 driver
if ETH_ENC28J60 && ETH_ENC28J60_0
config ETH_ENC28J60_0_NAME
string "Driver's name"
default "ETH_0"
config ETH_EN28J60_0_FULL_DUPLEX
bool "ENC28J60 full duplex"
default y
help
Enable Full Duplex. Device is configured half duplex
when disabled.
config ETH_ENC28J60_0_GPIO_PORT_NAME
string "GPIO controller port name"
default "GPIO_0"
help
GPIO port name through which ENC28J60C interruption is received.
config ETH_ENC28J60_0_GPIO_PIN
int "ENC28J60C INT GPIO PIN"
default 19
help
GPIO pin number used to connect INT
config ETH_ENC28J60_0_SPI_PORT_NAME
string "SPI master controller port name"
default "SPI_0"
help
Master SPI port name through which ENC28J60C chip is accessed.
config ETH_ENC28J60_0_SLAVE
hex "ETH_ENC28J60 SPI slave select pin"
default 1
help
ENC28J60C chip select pin.
config ETH_ENC28J60_0_SPI_BUS_FREQ
int "ENC28J60C SPI bus speed in Hz"
default 128
help
This is the maximum supported SPI bus frequency.
config ETH_ENC28J60_0_MAC3
hex "MAC Address Byte 3"
default 0
help
MACADDR<0:23> are Microchip's OUI.
This is the byte 3 of the MAC address.
MACADDR<31:24>
config ETH_ENC28J60_0_MAC4
hex "MAC Address Byte 4"
default 0
help
MACADDR<0:23> are Microchip's OUI.
This is the byte 4 of the MAC address.
MACADDR<40:32>
config ETH_ENC28J60_0_MAC5
hex "MAC Address Byte 5"
default 0
help
MACADDR<0:23> are Microchip's OUI.
This is the byte 5 of the MAC address.
MACADDR<48:41>
endif #ETH_ENC28J60 && ETH_ENC28J60_0