| # Kconfig - STM32 UART configuration |
| # |
| # Copyright (c) 2016 Open-RnD Sp. z o.o. |
| # |
| # SPDX-License-Identifier: Apache-2.0 |
| # |
| |
| menuconfig UART_STM32 |
| bool "STM32 MCU serial driver" |
| default n |
| select SERIAL_HAS_DRIVER |
| depends on SOC_FAMILY_STM32 |
| help |
| This option enables the UART driver for STM32F10x family of |
| processors. Say y if you wish to use serial port on STM32F10x |
| MCU. |
| |
| # --- port 1 --- |
| |
| config UART_STM32_PORT_1 |
| bool "Enable STM32 USART1 Port" |
| default n |
| depends on UART_STM32 |
| help |
| Enable support for USART1 port in the driver. Say y here |
| if you want to use USART1 device. |
| |
| config UART_STM32_PORT_1_NAME |
| string "Device Name for STM32 USART1 Port" |
| default "UART_1" |
| depends on UART_STM32_PORT_1 |
| help |
| This is the device name for USART1 port, and is |
| included in the device struct. |
| |
| if !HAS_DTS |
| config UART_STM32_PORT_1_BAUD_RATE |
| int "STM32 USART1 Baud Rate" |
| default 9600 |
| depends on UART_STM32_PORT_1 |
| help |
| The baud rate for USART1 port to be set to at boot. |
| |
| config UART_STM32_PORT_1_IRQ_PRI |
| int "STM32 USART1 Interrupt Priority" |
| default 0 |
| depends on UART_STM32_PORT_1 && UART_INTERRUPT_DRIVEN |
| help |
| The interrupt priority for USART1 port. |
| |
| endif # !HAS_DTS |
| # --- port 2 --- |
| |
| config UART_STM32_PORT_2 |
| bool "Enable STM32 USART2 Port" |
| default n |
| depends on UART_STM32 |
| help |
| Enable support for USART2 port in the driver. Say y here |
| if you want to use USART2 device. |
| |
| config UART_STM32_PORT_2_NAME |
| string "Device Name for STM32 USART2 Port" |
| default "UART_2" |
| depends on UART_STM32_PORT_2 |
| help |
| This is the device name for USART2 port, and is |
| included in the device struct. |
| |
| if !HAS_DTS |
| config UART_STM32_PORT_2_BAUD_RATE |
| int "STM32 USART2 Baud Rate" |
| default 9600 |
| depends on UART_STM32_PORT_2 |
| help |
| The baud rate for USART2 port to be set to at boot. |
| |
| config UART_STM32_PORT_2_IRQ_PRI |
| int "STM32 USART2 Interrupt Priority" |
| default 0 |
| depends on UART_STM32_PORT_2 && UART_INTERRUPT_DRIVEN |
| help |
| The interrupt priority for USART2 port. |
| |
| endif # !HAS_DTS |
| |
| # --- port 3 --- |
| |
| config UART_STM32_PORT_3 |
| bool "Enable STM32 USART3 Port" |
| default n |
| depends on UART_STM32 |
| help |
| Enable support for USART3 port in the driver. Say y here |
| if you want to use USART3 device. |
| |
| config UART_STM32_PORT_3_NAME |
| string "Device Name for STM32 USART3 Port" |
| default "UART_3" |
| depends on UART_STM32_PORT_3 |
| help |
| This is the device name for USART3 port, and is |
| included in the device struct. |
| |
| if !HAS_DTS |
| config UART_STM32_PORT_3_BAUD_RATE |
| int "STM32 USART3 Baud Rate" |
| default 9600 |
| depends on UART_STM32_PORT_3 |
| help |
| The baud rate for USART3 port to be set to at boot. |
| |
| config UART_STM32_PORT_3_IRQ_PRI |
| int "STM32 USART3 Interrupt Priority" |
| default 0 |
| depends on UART_STM32_PORT_3 && UART_INTERRUPT_DRIVEN |
| help |
| The interrupt priority for USART3 port. |
| |
| endif # !HAS_DTS |
