| # Kconfig - ETH_ENC28J60 Ethernet driver configuration options |
| |
| # |
| # Copyright (c) 2015 Intel Corporation |
| # |
| # SPDX-License-Identifier: Apache-2.0 |
| # |
| |
| menuconfig ETH_ENC28J60 |
| bool "ENC28J60C Ethernet Controller" |
| depends on NET_L2_ETHERNET |
| depends on SPI_LEGACY_API |
| depends on SPI |
| default n |
| help |
| ENC28J60C Stand-Alone Ethernet Controller |
| with SPI Interface |
| |
| config ETH_ENC28J60_RX_THREAD_STACK_SIZE |
| int "Stack size for internal incoming packet handler" |
| depends on ETH_ENC28J60 |
| default 800 |
| help |
| Size of the stack used for internal thread which is ran for |
| incoming packet processing. |
| |
| config ETH_ENC28J60_RX_THREAD_PRIO |
| int "Priority for internal incoming packet handler" |
| depends on ETH_ENC28J60 |
| default 2 |
| help |
| Priority level for internal thread which is ran for incoming |
| packet processing. |
| |
| config ETH_EN28J60_TIMEOUT |
| int "IP buffer timeout" |
| depends on ETH_ENC28J60 |
| default 100 |
| help |
| Given timeout in milliseconds. Maximum amount of time |
| that the driver will wait from the IP stack to get |
| a memory buffer before the Ethernet frame is dropped. |
| |
| config ETH_ENC28J60_0 |
| bool "ENC28J60C Ethernet port 0" |
| depends on ETH_ENC28J60 |
| default n |
| help |
| Include port 0 driver |
| |
| if ETH_ENC28J60 && ETH_ENC28J60_0 |
| config ETH_ENC28J60_0_NAME |
| string "Driver's name" |
| default "ETH_0" |
| |
| config ETH_EN28J60_0_FULL_DUPLEX |
| bool "ENC28J60 full duplex" |
| default y |
| help |
| Enable Full Duplex. Device is configured half duplex |
| when disabled. |
| |
| config ETH_ENC28J60_0_GPIO_PORT_NAME |
| string "GPIO controller port name" |
| default "GPIO_0" |
| help |
| GPIO port name through which ENC28J60C interruption is received. |
| |
| config ETH_ENC28J60_0_GPIO_PIN |
| int "ENC28J60C INT GPIO PIN" |
| default 19 |
| help |
| GPIO pin number used to connect INT |
| |
| config ETH_ENC28J60_0_SPI_PORT_NAME |
| string "SPI master controller port name" |
| default "SPI_0" |
| help |
| Master SPI port name through which ENC28J60C chip is accessed. |
| |
| config ETH_ENC28J60_0_SLAVE |
| hex "ETH_ENC28J60 SPI slave select pin" |
| default 1 |
| help |
| ENC28J60C chip select pin. |
| |
| config ETH_ENC28J60_0_SPI_BUS_FREQ |
| int "ENC28J60C SPI bus speed in Hz" |
| default 128 |
| help |
| This is the maximum supported SPI bus frequency. |
| |
| config ETH_ENC28J60_0_MAC3 |
| hex "MAC Address Byte 3" |
| default 0 |
| help |
| MACADDR<0:23> are Microchip's OUI. |
| This is the byte 3 of the MAC address. |
| MACADDR<31:24> |
| |
| config ETH_ENC28J60_0_MAC4 |
| hex "MAC Address Byte 4" |
| default 0 |
| help |
| MACADDR<0:23> are Microchip's OUI. |
| This is the byte 4 of the MAC address. |
| MACADDR<40:32> |
| |
| config ETH_ENC28J60_0_MAC5 |
| hex "MAC Address Byte 5" |
| default 0 |
| help |
| MACADDR<0:23> are Microchip's OUI. |
| This is the byte 5 of the MAC address. |
| MACADDR<48:41> |
| |
| endif #ETH_ENC28J60 && ETH_ENC28J60_0 |
