| /* |
| * Copyright (c) 2023 Würth Elektronik eiSos GmbH & Co. KG |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #define DT_DRV_COMPAT we_wsen_pads |
| |
| #include <string.h> |
| |
| #include <zephyr/sys/__assert.h> |
| #include <zephyr/sys/byteorder.h> |
| #include <zephyr/logging/log.h> |
| |
| #include "wsen_pads.h" |
| |
| LOG_MODULE_REGISTER(WSEN_PADS, CONFIG_SENSOR_LOG_LEVEL); |
| |
| /* |
| * List of supported output data rates. Index into this list is used as |
| * argument for PADS_setOutputDataRate() |
| */ |
| static const int32_t pads_odr_list[] = { |
| 0, 1, 10, 25, 50, 75, 100, 200, |
| }; |
| |
| static int pads_sample_fetch(const struct device *dev, enum sensor_channel channel) |
| { |
| struct pads_data *data = dev->data; |
| |
| __ASSERT_NO_MSG(channel == SENSOR_CHAN_ALL); |
| |
| if (PADS_getPressure_int(&data->sensor_interface, &data->pressure) != WE_SUCCESS) { |
| LOG_ERR("Failed to fetch %s sample.", "pressure"); |
| return -EIO; |
| } |
| |
| if (PADS_getTemperature_int(&data->sensor_interface, &data->temperature) != WE_SUCCESS) { |
| LOG_ERR("Failed to fetch %s sample.", "temperature"); |
| return -EIO; |
| } |
| |
| return 0; |
| } |
| |
| static int pads_channel_get(const struct device *dev, enum sensor_channel channel, |
| struct sensor_value *value) |
| { |
| struct pads_data *data = dev->data; |
| int32_t value_converted; |
| |
| if (channel == SENSOR_CHAN_AMBIENT_TEMP) { |
| value_converted = (int32_t)data->temperature; |
| |
| /* Convert temperature from 0.01 degrees Celsius to degrees Celsius */ |
| value->val1 = value_converted / 100; |
| value->val2 = (value_converted % 100) * (1000000 / 100); |
| } else if (channel == SENSOR_CHAN_PRESS) { |
| value_converted = (int32_t)data->pressure; |
| |
| /* Convert pressure from Pa to kPa */ |
| value->val1 = value_converted / 1000; |
| value->val2 = (value_converted % 1000) * (1000000 / 1000); |
| } else { |
| return -ENOTSUP; |
| } |
| |
| return 0; |
| } |
| |
| /* Set output data rate. See pads_odr_list for allowed values. */ |
| static int pads_odr_set(const struct device *dev, const struct sensor_value *odr) |
| { |
| struct pads_data *data = dev->data; |
| int odr_index; |
| |
| for (odr_index = 0; odr_index < ARRAY_SIZE(pads_odr_list); odr_index++) { |
| if (odr->val1 == pads_odr_list[odr_index] && odr->val2 == 0) { |
| break; |
| } |
| } |
| |
| if (odr_index == ARRAY_SIZE(pads_odr_list)) { |
| /* ODR not allowed (was not found in pads_odr_list) */ |
| LOG_ERR("Bad sampling frequency %d.%d", odr->val1, odr->val2); |
| return -EINVAL; |
| } |
| |
| if (PADS_setOutputDataRate(&data->sensor_interface, (PADS_outputDataRate_t)odr_index) != |
| WE_SUCCESS) { |
| LOG_ERR("Failed to set output data rate"); |
| return -EIO; |
| } |
| |
| return 0; |
| } |
| |
| static int pads_attr_set(const struct device *dev, enum sensor_channel chan, |
| enum sensor_attribute attr, const struct sensor_value *val) |
| { |
| if (chan != SENSOR_CHAN_ALL) { |
| LOG_WRN("attr_set() is not supported on channel %d.", chan); |
| return -ENOTSUP; |
| } |
| |
| if (attr == SENSOR_ATTR_SAMPLING_FREQUENCY) { |
| return pads_odr_set(dev, val); |
| } else { |
| return -ENOTSUP; |
| } |
| } |
| |
| static const struct sensor_driver_api pads_driver_api = { |
| .attr_set = pads_attr_set, |
| #if CONFIG_WSEN_PADS_TRIGGER |
| .trigger_set = pads_trigger_set, |
| #endif |
| .sample_fetch = pads_sample_fetch, |
| .channel_get = pads_channel_get, |
| }; |
| |
| static int pads_init(const struct device *dev) |
| { |
| const struct pads_config *config = dev->config; |
| struct pads_data *data = dev->data; |
| struct sensor_value odr; |
| int status; |
| uint8_t device_id; |
| |
| /* Initialize WE sensor interface */ |
| WE_sensorInterfaceType_t interface_type = data->sensor_interface.interfaceType; |
| |
| PADS_getDefaultInterface(&data->sensor_interface); |
| data->sensor_interface.interfaceType = interface_type; |
| |
| switch (data->sensor_interface.interfaceType) { |
| #if DT_ANY_INST_ON_BUS_STATUS_OKAY(i2c) |
| case WE_i2c: |
| data->sensor_interface.handle = (void *)&config->bus_cfg.i2c; |
| break; |
| #endif |
| #if DT_ANY_INST_ON_BUS_STATUS_OKAY(spi) |
| case WE_spi: |
| data->sensor_interface.handle = (void *)&config->bus_cfg.spi; |
| break; |
| #endif |
| default: |
| LOG_ERR("Invalid interface type"); |
| return -EINVAL; |
| } |
| |
| /* First communication test - check device ID */ |
| if (PADS_getDeviceID(&data->sensor_interface, &device_id) != WE_SUCCESS) { |
| LOG_ERR("Failed to read device ID."); |
| return -EIO; |
| } |
| |
| if (device_id != PADS_DEVICE_ID_VALUE) { |
| LOG_ERR("Invalid device ID 0x%x.", device_id); |
| return -EINVAL; |
| } |
| |
| /* Reset sensor */ |
| PADS_softReset(&data->sensor_interface, PADS_enable); |
| |
| k_sleep(K_USEC(50)); |
| |
| PADS_state_t swReset; |
| |
| do { |
| if (PADS_getSoftResetState(&data->sensor_interface, &swReset) != WE_SUCCESS) { |
| LOG_ERR("Failed to get sensor reset state."); |
| return -EIO; |
| } |
| } while (PADS_enable == swReset); |
| |
| if (PADS_enableBlockDataUpdate(&data->sensor_interface, PADS_enable) != WE_SUCCESS) { |
| LOG_ERR("Failed to enable block data update."); |
| return -EIO; |
| } |
| |
| #if CONFIG_WSEN_PADS_TRIGGER |
| status = pads_init_interrupt(dev); |
| if (status < 0) { |
| LOG_ERR("Failed to initialize data-ready interrupt."); |
| return status; |
| } |
| #endif |
| |
| odr.val1 = pads_odr_list[config->odr]; |
| odr.val2 = 0; |
| status = pads_odr_set(dev, &odr); |
| if (status < 0) { |
| LOG_ERR("Failed to set output data rate."); |
| return status; |
| } |
| |
| return 0; |
| } |
| |
| #if DT_NUM_INST_STATUS_OKAY(DT_DRV_COMPAT) == 0 |
| #warning "PADS driver enabled without any devices" |
| #endif |
| |
| /* |
| * Device creation macros |
| */ |
| |
| #define PADS_DEVICE_INIT(inst) \ |
| SENSOR_DEVICE_DT_INST_DEFINE(inst, \ |
| pads_init, \ |
| NULL, \ |
| &pads_data_##inst, \ |
| &pads_config_##inst, \ |
| POST_KERNEL, \ |
| CONFIG_SENSOR_INIT_PRIORITY, \ |
| &pads_driver_api); |
| |
| #ifdef CONFIG_WSEN_PADS_TRIGGER |
| #define PADS_CFG_IRQ(inst) .gpio_drdy = GPIO_DT_SPEC_INST_GET(inst, drdy_gpios) |
| #else |
| #define PADS_CFG_IRQ(inst) |
| #endif /* CONFIG_WSEN_PADS_TRIGGER */ |
| |
| #define PADS_CONFIG_COMMON(inst) \ |
| .odr = (PADS_outputDataRate_t)(DT_INST_ENUM_IDX(inst, odr)), \ |
| COND_CODE_1(DT_INST_NODE_HAS_PROP(inst, drdy_gpios), \ |
| (PADS_CFG_IRQ(inst)), ()) |
| |
| /* |
| * Instantiation macros used when device is on SPI bus. |
| */ |
| |
| #define PADS_SPI_OPERATION (SPI_WORD_SET(8) | SPI_OP_MODE_MASTER | SPI_MODE_CPOL | SPI_MODE_CPHA) |
| |
| #define PADS_CONFIG_SPI(inst) \ |
| { \ |
| .bus_cfg = { \ |
| .spi = SPI_DT_SPEC_INST_GET(inst, \ |
| PADS_SPI_OPERATION, \ |
| 0), \ |
| }, \ |
| PADS_CONFIG_COMMON(inst) \ |
| } |
| |
| /* |
| * Instantiation macros used when device is on I2C bus. |
| */ |
| |
| #define PADS_CONFIG_I2C(inst) \ |
| { \ |
| .bus_cfg = { \ |
| .i2c = I2C_DT_SPEC_INST_GET(inst), \ |
| }, \ |
| PADS_CONFIG_COMMON(inst) \ |
| } |
| |
| /* |
| * Main instantiation macro. Use of COND_CODE_1() selects the right |
| * bus-specific macro at preprocessor time. |
| */ |
| #define PADS_DEFINE(inst) \ |
| static struct pads_data pads_data_##inst = \ |
| COND_CODE_1(DT_INST_ON_BUS(inst, i2c), \ |
| ({ .sensor_interface = { .interfaceType = WE_i2c } }), ()) \ |
| COND_CODE_1(DT_INST_ON_BUS(inst, spi), \ |
| ({ .sensor_interface = { .interfaceType = WE_spi } }), ()); \ |
| static const struct pads_config pads_config_##inst = \ |
| COND_CODE_1(DT_INST_ON_BUS(inst, i2c), (PADS_CONFIG_I2C(inst)), ()) \ |
| COND_CODE_1(DT_INST_ON_BUS(inst, spi), (PADS_CONFIG_SPI(inst)), ()); \ |
| PADS_DEVICE_INIT(inst) |
| |
| DT_INST_FOREACH_STATUS_OKAY(PADS_DEFINE) |