| .. _atsame54_xpro: |
| |
| SAM E54 Xplained Pro Evaluation Kit |
| ################################### |
| |
| Overview |
| ******** |
| |
| The SAM E54 Xplained Pro evaluation kit is ideal for evaluation and |
| prototyping with the SAM E54 Cortex®-M4F processor-based |
| microcontrollers. The kit includes Atmel’s Embedded Debugger (EDBG), |
| which provides a full debug interface without the need for additional |
| hardware. |
| |
| .. image:: img/atsame54_xpro.jpg |
| :align: center |
| :alt: ATSAME54-XPRO |
| |
| Hardware |
| ******** |
| |
| - ATSAME54P20A ARM Cortex-M4F processor at 120 MHz |
| - 32.768 kHz crystal oscillator |
| - 12 MHz crystal oscillator |
| - 1024 KiB flash memory and 256 KiB of RAM |
| - One yellow user LED |
| - One mechanical user push button |
| - One reset button |
| - On-board USB based EDBG unit with serial console |
| - One QTouch® PTC button |
| - 32 MiB QSPI Flash |
| - ATECC508 CryptoAuthentication™ device |
| - AT24MAC402 serial EEPROM with EUI-48™ MAC address |
| - Ethernet |
| |
| - RJ45 connector with built-in magnetics |
| - KSZ8091RNA PHY |
| - 10Base-T/100Base-TX IEE 802.3 compliant Ethernet transceiver |
| |
| - USB interface, host, and device |
| - SD/SDIO card connector |
| |
| Supported Features |
| ================== |
| |
| The atsame54_xpro board configuration supports the following hardware |
| features: |
| |
| +-----------+------------+--------------------------------------+ |
| | Interface | Controller | Driver/Component | |
| +===========+============+======================================+ |
| | NVIC | on-chip | nested vector interrupt controller | |
| +-----------+------------+--------------------------------------+ |
| | SYSTICK | on-chip | systick | |
| +-----------+------------+--------------------------------------+ |
| | WDT | on-chip | Watchdog | |
| +-----------+------------+--------------------------------------+ |
| | GPIO | on-chip | I/O ports | |
| +-----------+------------+--------------------------------------+ |
| | PWM | on-chip | Pulse Width Modulation | |
| +-----------+------------+--------------------------------------+ |
| | USART | on-chip | Serial ports | |
| +-----------+------------+--------------------------------------+ |
| | SPI | on-chip | Serial Peripheral Interface ports | |
| +-----------+------------+--------------------------------------+ |
| | I2C | on-chip | Serial Peripheral Interface ports | |
| +-----------+------------+--------------------------------------+ |
| |
| Other hardware features are not currently supported by Zephyr. |
| |
| The default configuration can be found in the Kconfig |
| ``boards/arm/atsame54_xpro/atsame54_xpro_defconfig``. |
| |
| Pin Mapping |
| =========== |
| |
| The SAM E54 Xplained Pro evaluation kit has 4 GPIO controllers. These |
| controllers are responsible for pin muxing, input/output, pull-up, etc. |
| |
| For more details please refer to `SAM D5x/E5x Family Datasheet`_ and the `SAM E54 |
| Xplained Pro Schematic`_. |
| |
| .. image:: img/ATSAME54-XPRO-pinout.jpg |
| :align: center |
| :alt: ATSAME54-XPRO-pinout |
| |
| Default Zephyr Peripheral Mapping: |
| ---------------------------------- |
| - SERCOM2 USART TX : PB24 |
| - SERCOM2 USART RX : PB25 |
| - GPIO/PWM LED0 : PC18 |
| - GPIO SW0 : PB31 |
| |
| System Clock |
| ============ |
| |
| The SAME54 MCU is configured to use the 32.768 kHz external oscillator |
| with the on-chip PLL generating the 48 MHz system clock. |
| |
| Serial Port |
| =========== |
| |
| The SAME54 MCU has 8 SERCOM based USARTs with one configured as USARTs in |
| this BSP. SERCOM2 is the default Zephyr console. |
| |
| - SERCOM2 115200 8n1 connected to the onboard Atmel Embedded Debugger (EDBG) |
| |
| PWM |
| === |
| |
| The SAME54 MCU has 5 TCC based PWM units with up to 6 outputs each and a period |
| of 24 bits or 16 bits. If :code:`CONFIG_PWM_SAM0_TCC` is enabled then LED0 is |
| driven by TCC0 instead of by GPIO. |
| |
| SPI Port |
| ======== |
| |
| The SAME54 MCU has 8 SERCOM based SPIs. |
| |
| I2C Port |
| ======== |
| |
| The SAME54 MCU has 8 SERCOM based I2Cs. On the SAM E54 Xplained Pro, |
| SERCOM7 is connected to a AT24MAC402 EEPROM and a ATECC508A Crypto |
| Authentication device. |
| |
| Programming and Debugging |
| ************************* |
| |
| The SAM E54 Xplained Pro comes with a Atmel Embedded Debugger (EDBG). This |
| provides a debug interface to the SAME54 chip and is supported by |
| OpenOCD. |
| |
| Flashing |
| ======== |
| |
| #. Build the Zephyr kernel and the ``hello_world`` sample application: |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: atsame54_xpro |
| :goals: build |
| :compact: |
| |
| #. Connect the SAM E54 Xplained Pro to your host computer using the USB debug |
| port. |
| |
| #. Run your favorite terminal program to listen for output. Under Linux the |
| terminal should be :code:`/dev/ttyACM0`. For example: |
| |
| .. code-block:: console |
| |
| $ minicom -D /dev/ttyACM0 -o |
| |
| The -o option tells minicom not to send the modem initialization |
| string. Connection should be configured as follows: |
| |
| - Speed: 115200 |
| - Data: 8 bits |
| - Parity: None |
| - Stop bits: 1 |
| |
| #. To flash an image: |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: atsame54_xpro |
| :goals: flash |
| :compact: |
| |
| You should see "Hello World! atsame54_xpro" in your terminal. |
| |
| References |
| ********** |
| |
| .. target-notes:: |
| |
| .. _Microchip website: |
| http://www.microchip.com/DevelopmentTools/ProductDetails.aspx?PartNO=ATSAME54-XPRO |
| |
| .. _SAM D5x/E5x Family Datasheet: |
| http://ww1.microchip.com/downloads/en/DeviceDoc/60001507C.pdf |
| |
| .. _SAM E54 Xplained Pro Schematic: |
| http://ww1.microchip.com/downloads/en/DeviceDoc/SAME54-Xplained-Pro_Design-Documentation.zip |