| # TI CC13xx / CC26xx IEEE 802.15.4 configuration options |
| |
| # Copyright (c) 2019 Brett Witherspoon |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| menuconfig IEEE802154_CC13XX_CC26XX |
| bool "TI CC13xx / CC26xx IEEE 802.15.4 driver support" |
| select CRC |
| default y |
| depends on DT_HAS_TI_CC13XX_CC26XX_IEEE802154_ENABLED |
| |
| if IEEE802154_CC13XX_CC26XX |
| |
| config IEEE802154_CC13XX_CC26XX_INIT_PRIO |
| int "TI CC13xx / CC26xx IEEE 802.15.4 initialization priority" |
| default 80 |
| help |
| Set the initialization priority number. |
| |
| config IEEE802154_CC13XX_CC26XX_RADIO_TX_RETRIES |
| int "Radio Transmission attempts" |
| default NET_L2_IEEE802154_RADIO_TX_RETRIES if NET_L2_IEEE802154 |
| default 3 |
| range 1 7 |
| help |
| Number of transmission attempts radio driver should do, before |
| replying it could not send the packet. |
| |
| config IEEE802154_CC13XX_CC26XX_RADIO_CSMA_CA_MAX_BO |
| int "CSMA maximum backoffs" |
| default NET_L2_IEEE802154_RADIO_CSMA_CA_MAX_BO if NET_L2_IEEE802154_RADIO_CSMA_CA |
| default 4 |
| range 1 5 |
| help |
| The maximum number of backoffs the CSMA-CA algorithm will attempt |
| before declaring a channel access failure. |
| |
| config IEEE802154_CC13XX_CC26XX_RADIO_CSMA_CA_MIN_BE |
| int "CSMA MAC minimum backoff exponent" |
| default NET_L2_IEEE802154_RADIO_CSMA_CA_MIN_BE if NET_L2_IEEE802154_RADIO_CSMA_CA |
| default 3 |
| range 1 8 |
| help |
| The minimum value of the backoff exponent (BE) in the CSMA-CA |
| algorithm. |
| |
| config IEEE802154_CC13XX_CC26XX_RADIO_CSMA_CA_MAX_BE |
| int "CSMA MAC maximum backoff exponent" |
| default NET_L2_IEEE802154_RADIO_CSMA_CA_MAX_BE if NET_L2_IEEE802154_RADIO_CSMA_CA |
| default 5 |
| range 1 8 |
| help |
| The maximum value of the backoff exponent (BE) in the CSMA-CA |
| algorithm. |
| |
| endif # IEEE802154_CC13XX_CC26XX |
| |
| menuconfig IEEE802154_CC13XX_CC26XX_SUB_GHZ |
| bool "TI CC13xx / CC26xx IEEE 802.15.4g driver support" |
| default y |
| depends on DT_HAS_TI_CC13XX_CC26XX_IEEE802154_SUBGHZ_ENABLED |
| |
| if IEEE802154_CC13XX_CC26XX_SUB_GHZ |
| |
| config IEEE802154_CC13XX_CC26XX_SUB_GHZ_NUM_RX_BUF |
| int "TI CC13xx / CC26xx IEEE 802.15.4g receive buffer count" |
| default 2 |
| help |
| This option allows the user to configure the number of |
| receive buffers. |
| |
| config IEEE802154_CC13XX_CC26XX_SUB_GHZ_CS_THRESHOLD |
| int "TI CC13xx / CC26xx IEEE 802.15.4g Carrier Sense ED Threshold in dBm" |
| default -80 # Based on SUN FSK, 200 kHz bit rate, no FEC, see IEEE 802.15.4-2020, section 19.6.7 |
| help |
| This option sets the energy detection (ED) threshold for |
| clear channel assessment (CCA) modes 1 or 3 in the CSMA/CA |
| algorithm. Except for the SUN O-QPSK PHY, the ED threshold |
| shall correspond to a received signal power of at most 10 dB |
| greater than the specified receiver sensitivity for that PHY, |
| or in accordance with local regulations (see IEEE 802.15.4-2020, |
| section 10.2.8). For the SUN O-QPSK PHY, the ED threshold shall |
| comply with IEEE 802.15.4-2020, section 21.5.13. |
| |
| config IEEE802154_CC13XX_CC26XX_SUB_GHZ_INIT_PRIO |
| int "TI CC13xx / CC26xx IEEE 802.15.4g initialization priority" |
| default 80 |
| help |
| Set the initialization priority number. |
| |
| config IEEE802154_CC13XX_CC26XX_SUB_GHZ_RADIO_TX_RETRIES |
| bool |
| select DEPRECATED |
| help |
| DEPRECATED - use NET_L2_IEEE802154_RADIO_TX_RETRIES instead |
| |
| config IEEE802154_CC13XX_CC26XX_SUB_GHZ_CUSTOM_RADIO_SETUP |
| bool "Use custom radio setup structures (advanced)" |
| default n |
| help |
| Imports the radio setup structure from an external module instead of using |
| the default one. |
| Allows overriding the RF modulation / protocol settings. |
| |
| config IEEE802154_CC13XX_CC26XX_SUB_GHZ_CUSTOM_POWER_TABLE |
| bool "Use custom power table structure (advanced)" |
| default n |
| help |
| Imports the radio power table from an external module. |
| Allows overriding the RF modulation settings. |
| |
| endif # IEEE802154_CC13XX_CC26XX_SUB_GHZ |
