|  | /* | 
|  | * Copyright (c) 2024 ITE Technology Inc. | 
|  | * | 
|  | * SPDX-License-Identifier: Apache-2.0 | 
|  | */ | 
|  |  | 
|  | #define DT_DRV_COMPAT ite_it8xxx2_spi | 
|  |  | 
|  | #include <zephyr/logging/log.h> | 
|  | LOG_MODULE_REGISTER(spi_it8xxx2, CONFIG_SPI_LOG_LEVEL); | 
|  |  | 
|  | #include <zephyr/irq.h> | 
|  | #include <zephyr/drivers/spi.h> | 
|  | #include <zephyr/drivers/pinctrl.h> | 
|  | #include <zephyr/pm/policy.h> | 
|  | #include <soc.h> | 
|  |  | 
|  | #include "spi_context.h" | 
|  |  | 
|  | #define BYTE_0(x) (uint8_t)(((x) >> 0) & 0xFF) | 
|  | #define BYTE_1(x) (uint8_t)(((x) >> 8) & 0xFF) | 
|  | #define BYTE_2(x) (uint8_t)(((x) >> 16) & 0xFF) | 
|  |  | 
|  | #define SRAM_BASE_ADDR DT_REG_ADDR(DT_NODELABEL(sram0)) | 
|  |  | 
|  | #define SPI_CHIP_SELECT_COUNT   2 | 
|  | #define SPI_CMDQ_WR_CMD_LEN_MAX 16 | 
|  | #define SPI_CMDQ_DATA_LEN_MAX   0xFFFF | 
|  |  | 
|  | /* IT8xxx2 SSPI Registers Definition */ | 
|  | #define SPI01_CTRL1    0x01 | 
|  | #define CLOCK_POLARTY  BIT(6) | 
|  | #define SSCK_FREQ_MASK (BIT(2) | BIT(3) | BIT(4)) | 
|  | #define INTERRUPT_EN   BIT(1) | 
|  |  | 
|  | #define SPI04_CTRL3 0x04 | 
|  | #define AUTO_MODE   BIT(5) | 
|  |  | 
|  | #define SPI05_CH0_CMD_ADDR_LB     0x05 | 
|  | #define SPI06_CH0_CMD_ADDR_HB     0x06 | 
|  | #define SPI0C_INT_STS             0x0C | 
|  | #define SPI_CMDQ_BUS_END_INT_MASK BIT(4) | 
|  | #define SPI_DMA_RBUF_1_FULL       BIT(2) | 
|  | #define SPI_DMA_RBUF_0_FULL       BIT(1) | 
|  | #define SPI_CMDQ_BUS_END          BIT(0) | 
|  |  | 
|  | #define SPI0D_CTRL5       0x0D | 
|  | #define CH1_SEL_CMDQ      BIT(5) | 
|  | #define CH0_SEL_CMDQ      BIT(4) | 
|  | #define SCK_FREQ_DIV_1_EN BIT(1) | 
|  | #define CMDQ_MODE_EN      BIT(0) | 
|  |  | 
|  | #define SPI0E_CH0_WR_MEM_ADDR_LB  0x0E | 
|  | #define SPI0F_CH0_WR_MEM_ADDR_HB  0x0F | 
|  | #define SPI12_CH1_CMD_ADDR_LB     0x12 | 
|  | #define SPI13_CH1_CMD_ADDR_HB     0x13 | 
|  | #define SPI14_CH1_WR_MEM_ADDR_LB  0x14 | 
|  | #define SPI15_CH1_WR_MEM_ADDR_HB  0x15 | 
|  | #define SPI21_CH0_CMD_ADDR_HB2    0x21 | 
|  | #define SPI23_CH0_WR_MEM_ADDR_HB2 0x23 | 
|  | #define SPI25_CH1_CMD_ADDR_HB2    0x25 | 
|  | #define SPI27_CH1_WR_MEM_ADDR_HB2 0x27 | 
|  |  | 
|  | #define ECPM_BASE_ADDR          DT_REG_ADDR(DT_NODELABEL(ecpm)) | 
|  | #define ECPM05_CLK_GATING_CTRL3 0x05 | 
|  | #define SSPI_CLOCK_GATING       BIT(1) | 
|  |  | 
|  | struct spi_it8xxx2_cmdq_data { | 
|  | uint8_t spi_write_cmd_length; | 
|  |  | 
|  | union { | 
|  | uint8_t value; | 
|  | struct { | 
|  | uint8_t cmd_end: 1; | 
|  | uint8_t read_write: 1; | 
|  | uint8_t auto_check_sts: 1; | 
|  | uint8_t cs_active: 1; | 
|  | uint8_t reserved: 1; | 
|  | uint8_t cmd_mode: 2; | 
|  | uint8_t dtr: 1; | 
|  | } __packed fields; | 
|  | } __packed command; | 
|  |  | 
|  | uint8_t data_length_lb; | 
|  | uint8_t data_length_hb; | 
|  | uint8_t data_addr_lb; | 
|  | uint8_t data_addr_hb; | 
|  | uint8_t check_bit_mask; | 
|  | uint8_t check_bit_value; | 
|  |  | 
|  | uint8_t write_data[SPI_CMDQ_WR_CMD_LEN_MAX]; | 
|  | }; | 
|  |  | 
|  | struct spi_it8xxx2_config { | 
|  | mm_reg_t base; | 
|  | const struct pinctrl_dev_config *pcfg; | 
|  | uint8_t spi_irq; | 
|  | }; | 
|  |  | 
|  | struct spi_it8xxx2_data { | 
|  | struct spi_context ctx; | 
|  | struct spi_it8xxx2_cmdq_data cmdq_data; | 
|  | size_t transfer_len; | 
|  | size_t receive_len; | 
|  | }; | 
|  |  | 
|  | static inline void spi_it8xxx2_turn_on_clk(const struct device *dev, const bool enable) | 
|  | { | 
|  | ARG_UNUSED(dev); | 
|  |  | 
|  | uint8_t reg_val; | 
|  | unsigned int key = irq_lock(); | 
|  |  | 
|  | reg_val = sys_read8(ECPM_BASE_ADDR + ECPM05_CLK_GATING_CTRL3); | 
|  | if (enable) { | 
|  | sys_write8(reg_val & ~SSPI_CLOCK_GATING, ECPM_BASE_ADDR + ECPM05_CLK_GATING_CTRL3); | 
|  | } else { | 
|  | sys_write8(reg_val | SSPI_CLOCK_GATING, ECPM_BASE_ADDR + ECPM05_CLK_GATING_CTRL3); | 
|  | } | 
|  |  | 
|  | irq_unlock(key); | 
|  | }; | 
|  |  | 
|  | static inline int spi_it8xxx2_set_freq(const struct device *dev, const uint32_t frequency) | 
|  | { | 
|  | const struct spi_it8xxx2_config *cfg = dev->config; | 
|  | uint8_t freq_div[8] = {2, 4, 6, 8, 10, 12, 14, 16}; | 
|  | uint32_t clk_pll, clk_sspi; | 
|  | uint8_t reg_val; | 
|  |  | 
|  | clk_pll = chip_get_pll_freq(); | 
|  | clk_sspi = clk_pll / (((IT8XXX2_ECPM_SCDCR2 & 0xF0) >> 4) + 1U); | 
|  | if (frequency < (clk_sspi / 16) || frequency > clk_sspi) { | 
|  | LOG_ERR("Unsupported frequency %d", frequency); | 
|  | return -ENOTSUP; | 
|  | } | 
|  |  | 
|  | if (frequency == clk_sspi) { | 
|  | sys_write8(sys_read8(cfg->base + SPI0D_CTRL5) | SCK_FREQ_DIV_1_EN, | 
|  | cfg->base + SPI0D_CTRL5); | 
|  | } else { | 
|  | for (int i = 0; i <= ARRAY_SIZE(freq_div); i++) { | 
|  | if (i == ARRAY_SIZE(freq_div)) { | 
|  | LOG_ERR("Unknown frequency %d", frequency); | 
|  | return -ENOTSUP; | 
|  | } | 
|  | if (frequency == (clk_sspi / freq_div[i])) { | 
|  | sys_write8(sys_read8(cfg->base + SPI0D_CTRL5) & ~SCK_FREQ_DIV_1_EN, | 
|  | cfg->base + SPI0D_CTRL5); | 
|  | reg_val = sys_read8(cfg->base + SPI01_CTRL1); | 
|  | reg_val = (reg_val & (~SSCK_FREQ_MASK)) | (i << 2); | 
|  | sys_write8(reg_val, cfg->base + SPI01_CTRL1); | 
|  | break; | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | LOG_DBG("freq: pll %dHz, sspi %dHz, ssck %dHz", clk_pll, clk_sspi, frequency); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int spi_it8xxx2_configure(const struct device *dev, const struct spi_config *spi_cfg) | 
|  | { | 
|  | const struct spi_it8xxx2_config *cfg = dev->config; | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  | struct spi_context *ctx = &data->ctx; | 
|  | int ret; | 
|  | uint8_t reg_val; | 
|  |  | 
|  | if (spi_cfg->slave > (SPI_CHIP_SELECT_COUNT - 1)) { | 
|  | LOG_ERR("Slave %d is greater than %d", spi_cfg->slave, SPI_CHIP_SELECT_COUNT - 1); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | LOG_DBG("chip select: %d, operation: 0x%x", spi_cfg->slave, spi_cfg->operation); | 
|  |  | 
|  | if (SPI_OP_MODE_GET(spi_cfg->operation) == SPI_OP_MODE_SLAVE) { | 
|  | LOG_ERR("Unsupported SPI slave mode"); | 
|  | return -ENOTSUP; | 
|  | } | 
|  |  | 
|  | if (SPI_MODE_GET(spi_cfg->operation) & SPI_MODE_LOOP) { | 
|  | LOG_ERR("Unsupported loopback mode"); | 
|  | return -ENOTSUP; | 
|  | } | 
|  |  | 
|  | if (SPI_MODE_GET(spi_cfg->operation) & SPI_MODE_CPHA) { | 
|  | LOG_ERR("Unsupported cpha mode"); | 
|  | return -ENOTSUP; | 
|  | } | 
|  |  | 
|  | reg_val = sys_read8(cfg->base + SPI01_CTRL1); | 
|  | if (SPI_MODE_GET(spi_cfg->operation) & SPI_MODE_CPOL) { | 
|  | reg_val |= CLOCK_POLARTY; | 
|  | } else { | 
|  | reg_val &= ~CLOCK_POLARTY; | 
|  | } | 
|  | sys_write8(reg_val, cfg->base + SPI01_CTRL1); | 
|  |  | 
|  | if (SPI_WORD_SIZE_GET(spi_cfg->operation) != 8) { | 
|  | return -ENOTSUP; | 
|  | } | 
|  |  | 
|  | if (IS_ENABLED(CONFIG_SPI_EXTENDED_MODES) && | 
|  | (spi_cfg->operation & SPI_LINES_MASK) != SPI_LINES_SINGLE) { | 
|  | LOG_ERR("Only single line mode is supported"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | ret = spi_it8xxx2_set_freq(dev, spi_cfg->frequency); | 
|  | if (ret) { | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | reg_val = sys_read8(cfg->base + SPI0C_INT_STS); | 
|  | reg_val = (reg_val & (~SPI_CMDQ_BUS_END_INT_MASK)); | 
|  | sys_write8(reg_val, cfg->base + SPI0C_INT_STS); | 
|  |  | 
|  | ctx->config = spi_cfg; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static inline bool spi_it8xxx2_transfer_done(struct spi_context *ctx) | 
|  | { | 
|  | return !spi_context_tx_buf_on(ctx) && !spi_context_rx_buf_on(ctx); | 
|  | } | 
|  |  | 
|  | static void spi_it8xxx2_complete(const struct device *dev, const int status) | 
|  | { | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  | struct spi_context *ctx = &data->ctx; | 
|  |  | 
|  | /* Permit to enter power policy and idle mode. */ | 
|  | pm_policy_state_lock_put(PM_STATE_STANDBY, PM_ALL_SUBSTATES); | 
|  | chip_permit_idle(); | 
|  |  | 
|  | /* disable spi clock */ | 
|  | spi_it8xxx2_turn_on_clk(dev, false); | 
|  |  | 
|  | spi_context_complete(ctx, dev, status); | 
|  | } | 
|  |  | 
|  | static inline void spi_it8xxx2_tx(const struct device *dev) | 
|  | { | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  | struct spi_context *ctx = &data->ctx; | 
|  | uint32_t mem_address; | 
|  |  | 
|  | if (ctx->tx_count > 1) { | 
|  | data->cmdq_data.command.fields.cs_active = 1; | 
|  | } else { | 
|  | data->cmdq_data.command.fields.cs_active = 0; | 
|  | } | 
|  | data->cmdq_data.command.fields.cmd_end = 1; | 
|  | data->cmdq_data.command.fields.read_write = 0; | 
|  | if (ctx->tx_len <= SPI_CMDQ_WR_CMD_LEN_MAX) { | 
|  | data->cmdq_data.spi_write_cmd_length = ctx->tx_len; | 
|  | memcpy(data->cmdq_data.write_data, ctx->tx_buf, ctx->tx_len); | 
|  | data->cmdq_data.data_length_lb = 0; | 
|  | data->cmdq_data.data_length_hb = 0; | 
|  | data->cmdq_data.data_addr_lb = 0; | 
|  | data->cmdq_data.data_addr_hb = 0; | 
|  | } else { | 
|  | data->cmdq_data.spi_write_cmd_length = SPI_CMDQ_WR_CMD_LEN_MAX; | 
|  | memcpy(data->cmdq_data.write_data, ctx->tx_buf, SPI_CMDQ_WR_CMD_LEN_MAX); | 
|  | data->cmdq_data.data_length_lb = BYTE_0(ctx->tx_len - SPI_CMDQ_WR_CMD_LEN_MAX); | 
|  | data->cmdq_data.data_length_hb = BYTE_1(ctx->tx_len - SPI_CMDQ_WR_CMD_LEN_MAX); | 
|  | mem_address = (uint32_t)(ctx->tx_buf + SPI_CMDQ_WR_CMD_LEN_MAX) - SRAM_BASE_ADDR; | 
|  | data->cmdq_data.data_addr_lb = BYTE_0(mem_address); | 
|  | data->cmdq_data.data_addr_hb = BYTE_1(mem_address); | 
|  | data->cmdq_data.check_bit_mask |= ((BYTE_2(mem_address)) & 0x03); | 
|  | } | 
|  | data->transfer_len = ctx->tx_len; | 
|  | } | 
|  |  | 
|  | static inline void spi_it8xxx2_rx(const struct device *dev) | 
|  | { | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  | struct spi_context *ctx = &data->ctx; | 
|  |  | 
|  | if (ctx->rx_count > 1) { | 
|  | data->cmdq_data.command.fields.cs_active = 1; | 
|  | } else { | 
|  | data->cmdq_data.command.fields.cs_active = 0; | 
|  | } | 
|  | data->cmdq_data.command.fields.cmd_end = 1; | 
|  | data->cmdq_data.command.fields.read_write = 1; | 
|  | data->cmdq_data.spi_write_cmd_length = 0; | 
|  | data->cmdq_data.data_length_lb = BYTE_0(ctx->rx_len); | 
|  | data->cmdq_data.data_length_hb = BYTE_1(ctx->rx_len); | 
|  | data->cmdq_data.data_addr_lb = 0; | 
|  | data->cmdq_data.data_addr_hb = 0; | 
|  | data->receive_len = ctx->rx_len; | 
|  | } | 
|  |  | 
|  | static inline void spi_it8xxx2_tx_rx(const struct device *dev) | 
|  | { | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  | struct spi_context *ctx = &data->ctx; | 
|  | uint32_t mem_address; | 
|  |  | 
|  | data->cmdq_data.command.fields.cmd_end = 1; | 
|  | if (ctx->tx_len <= SPI_CMDQ_WR_CMD_LEN_MAX) { | 
|  | data->cmdq_data.command.fields.cs_active = 0; | 
|  | data->cmdq_data.command.fields.read_write = 1; | 
|  | data->cmdq_data.spi_write_cmd_length = ctx->tx_len; | 
|  | memcpy(data->cmdq_data.write_data, ctx->tx_buf, ctx->tx_len); | 
|  | if (ctx->rx_buf == ctx->tx_buf) { | 
|  | spi_context_update_tx(ctx, 1, ctx->tx_len); | 
|  | spi_context_update_rx(ctx, 1, ctx->rx_len); | 
|  | } | 
|  |  | 
|  | data->cmdq_data.data_length_lb = BYTE_0(ctx->rx_len); | 
|  | data->cmdq_data.data_length_hb = BYTE_1(ctx->rx_len); | 
|  | data->cmdq_data.data_addr_lb = 0; | 
|  | data->cmdq_data.data_addr_hb = 0; | 
|  | data->transfer_len = ctx->tx_len; | 
|  | data->receive_len = ctx->rx_len; | 
|  | } else { | 
|  | data->cmdq_data.command.fields.cs_active = 1; | 
|  | data->cmdq_data.command.fields.read_write = 0; | 
|  | data->cmdq_data.spi_write_cmd_length = SPI_CMDQ_WR_CMD_LEN_MAX; | 
|  | memcpy(data->cmdq_data.write_data, ctx->tx_buf, SPI_CMDQ_WR_CMD_LEN_MAX); | 
|  | data->cmdq_data.data_length_lb = BYTE_0(ctx->tx_len - SPI_CMDQ_WR_CMD_LEN_MAX); | 
|  | data->cmdq_data.data_length_hb = BYTE_1(ctx->tx_len - SPI_CMDQ_WR_CMD_LEN_MAX); | 
|  |  | 
|  | mem_address = (uint32_t)(ctx->tx_buf + SPI_CMDQ_WR_CMD_LEN_MAX) - SRAM_BASE_ADDR; | 
|  | data->cmdq_data.data_addr_lb = BYTE_0(mem_address); | 
|  | data->cmdq_data.data_addr_hb = BYTE_1(mem_address); | 
|  | data->cmdq_data.check_bit_mask |= ((BYTE_2(mem_address)) & 0x03); | 
|  | if (ctx->rx_buf == ctx->tx_buf) { | 
|  | spi_context_update_tx(ctx, 1, ctx->tx_len); | 
|  | spi_context_update_rx(ctx, 1, ctx->rx_len); | 
|  | } | 
|  | data->transfer_len = ctx->tx_len; | 
|  | data->receive_len = 0; | 
|  | } | 
|  | } | 
|  |  | 
|  | static int spi_it8xxx2_next_xfer(const struct device *dev) | 
|  | { | 
|  | const struct spi_it8xxx2_config *cfg = dev->config; | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  | struct spi_context *ctx = &data->ctx; | 
|  | uint8_t reg_val; | 
|  | uint32_t cmd_address, mem_address; | 
|  |  | 
|  | if (spi_it8xxx2_transfer_done(ctx)) { | 
|  | spi_it8xxx2_complete(dev, 0); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | if (spi_context_longest_current_buf(ctx) > SPI_CMDQ_DATA_LEN_MAX) { | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | memset(&data->cmdq_data, 0, sizeof(struct spi_it8xxx2_cmdq_data)); | 
|  |  | 
|  | /* Prepare command queue data */ | 
|  | if (!spi_context_tx_on(ctx)) { | 
|  | /* rx only, nothing to tx */ | 
|  | spi_it8xxx2_rx(dev); | 
|  | } else if (!spi_context_rx_on(ctx)) { | 
|  | /* tx only, nothing to rx */ | 
|  | spi_it8xxx2_tx(dev); | 
|  | } else { | 
|  | spi_it8xxx2_tx_rx(dev); | 
|  | } | 
|  |  | 
|  | cmd_address = (uint32_t)(&data->cmdq_data) - SRAM_BASE_ADDR; | 
|  | mem_address = (uint32_t)ctx->rx_buf - SRAM_BASE_ADDR; | 
|  | if (ctx->config->slave == 0) { | 
|  | sys_write8(BYTE_0(cmd_address), cfg->base + SPI05_CH0_CMD_ADDR_LB); | 
|  | sys_write8(BYTE_1(cmd_address), cfg->base + SPI06_CH0_CMD_ADDR_HB); | 
|  | sys_write8(BYTE_2(cmd_address), cfg->base + SPI21_CH0_CMD_ADDR_HB2); | 
|  |  | 
|  | if (spi_context_rx_on(ctx)) { | 
|  | sys_write8(BYTE_0(mem_address), cfg->base + SPI0E_CH0_WR_MEM_ADDR_LB); | 
|  | sys_write8(BYTE_1(mem_address), cfg->base + SPI0F_CH0_WR_MEM_ADDR_HB); | 
|  | sys_write8(BYTE_2(mem_address), cfg->base + SPI23_CH0_WR_MEM_ADDR_HB2); | 
|  | } | 
|  | } else { | 
|  | sys_write8(BYTE_0(cmd_address), cfg->base + SPI12_CH1_CMD_ADDR_LB); | 
|  | sys_write8(BYTE_1(cmd_address), cfg->base + SPI13_CH1_CMD_ADDR_HB); | 
|  | sys_write8(BYTE_2(cmd_address), cfg->base + SPI25_CH1_CMD_ADDR_HB2); | 
|  |  | 
|  | if (spi_context_rx_on(ctx)) { | 
|  | sys_write8(BYTE_0(mem_address), cfg->base + SPI14_CH1_WR_MEM_ADDR_LB); | 
|  | sys_write8(BYTE_1(mem_address), cfg->base + SPI15_CH1_WR_MEM_ADDR_HB); | 
|  | sys_write8(BYTE_2(mem_address), cfg->base + SPI27_CH1_WR_MEM_ADDR_HB2); | 
|  | } | 
|  | } | 
|  |  | 
|  | sys_write8(sys_read8(cfg->base + SPI01_CTRL1) | INTERRUPT_EN, cfg->base + SPI01_CTRL1); | 
|  |  | 
|  | reg_val = sys_read8(cfg->base + SPI0D_CTRL5); | 
|  | reg_val |= (ctx->config->slave == 0) ? CH0_SEL_CMDQ : CH1_SEL_CMDQ; | 
|  | sys_write8(reg_val | CMDQ_MODE_EN, cfg->base + SPI0D_CTRL5); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int transceive(const struct device *dev, const struct spi_config *config, | 
|  | const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs, | 
|  | bool asynchronous, spi_callback_t cb, void *userdata) | 
|  | { | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  | struct spi_context *ctx = &data->ctx; | 
|  | int ret; | 
|  |  | 
|  | spi_context_lock(ctx, asynchronous, cb, userdata, config); | 
|  |  | 
|  | /* Configure spi */ | 
|  | ret = spi_it8xxx2_configure(dev, config); | 
|  | if (ret) { | 
|  | spi_context_release(ctx, ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * The EC processor(CPU) cannot be in the k_cpu_idle() and power | 
|  | * policy during the transactions with the CQ mode. | 
|  | * Otherwise, the EC processor would be clock gated. | 
|  | */ | 
|  | chip_block_idle(); | 
|  | pm_policy_state_lock_get(PM_STATE_STANDBY, PM_ALL_SUBSTATES); | 
|  |  | 
|  | /* enable spi clock */ | 
|  | spi_it8xxx2_turn_on_clk(dev, true); | 
|  |  | 
|  | spi_context_buffers_setup(ctx, tx_bufs, rx_bufs, 1); | 
|  | ret = spi_it8xxx2_next_xfer(dev); | 
|  | if (!ret) { | 
|  | ret = spi_context_wait_for_completion(ctx); | 
|  | } else { | 
|  | spi_it8xxx2_complete(dev, ret); | 
|  | } | 
|  |  | 
|  | spi_context_release(ctx, ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int it8xxx2_transceive(const struct device *dev, const struct spi_config *config, | 
|  | const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs) | 
|  | { | 
|  | return transceive(dev, config, tx_bufs, rx_bufs, false, NULL, NULL); | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_SPI_ASYNC | 
|  | static int it8xxx2_transceive_async(const struct device *dev, const struct spi_config *config, | 
|  | const struct spi_buf_set *tx_bufs, | 
|  | const struct spi_buf_set *rx_bufs, spi_callback_t cb, | 
|  | void *userdata) | 
|  | { | 
|  | return transceive(dev, config, tx_bufs, rx_bufs, true, cb, userdata); | 
|  | } | 
|  | #endif /* CONFIG_SPI_ASYNC */ | 
|  |  | 
|  | static int it8xxx2_release(const struct device *dev, const struct spi_config *config) | 
|  | { | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  |  | 
|  | spi_context_unlock_unconditionally(&data->ctx); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void it8xxx2_spi_isr(const void *arg) | 
|  | { | 
|  | const struct device *dev = arg; | 
|  | const struct spi_it8xxx2_config *cfg = dev->config; | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  | struct spi_context *ctx = &data->ctx; | 
|  | uint8_t reg_val; | 
|  | int ret; | 
|  |  | 
|  | reg_val = sys_read8(cfg->base + SPI0C_INT_STS); | 
|  | sys_write8(reg_val, cfg->base + SPI0C_INT_STS); | 
|  | if (reg_val & (SPI_DMA_RBUF_0_FULL | SPI_DMA_RBUF_1_FULL)) { | 
|  | LOG_INF("Triggered dma ring buffer full interrupt, status: 0x%x", reg_val); | 
|  | } | 
|  |  | 
|  | if (reg_val & SPI_CMDQ_BUS_END) { | 
|  | reg_val = sys_read8(cfg->base + SPI0D_CTRL5); | 
|  | if (ctx->config->slave == 0) { | 
|  | reg_val &= ~CH0_SEL_CMDQ; | 
|  | } else { | 
|  | reg_val &= ~CH1_SEL_CMDQ; | 
|  | } | 
|  | sys_write8(reg_val, cfg->base + SPI0D_CTRL5); | 
|  |  | 
|  | spi_context_update_tx(ctx, 1, data->transfer_len); | 
|  | spi_context_update_rx(ctx, 1, data->receive_len); | 
|  | ret = spi_it8xxx2_next_xfer(dev); | 
|  | if (ret) { | 
|  | spi_it8xxx2_complete(dev, ret); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static int spi_it8xxx2_init(const struct device *dev) | 
|  | { | 
|  | const struct spi_it8xxx2_config *cfg = dev->config; | 
|  | struct spi_it8xxx2_data *data = dev->data; | 
|  | int ret; | 
|  |  | 
|  | ret = pinctrl_apply_state(cfg->pcfg, PINCTRL_STATE_DEFAULT); | 
|  | if (ret) { | 
|  | LOG_ERR("Failed to set default pinctrl"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | /* Enable one-shot mode */ | 
|  | sys_write8(sys_read8(cfg->base + SPI04_CTRL3) & ~AUTO_MODE, cfg->base + SPI04_CTRL3); | 
|  |  | 
|  | irq_connect_dynamic(cfg->spi_irq, 0, it8xxx2_spi_isr, dev, 0); | 
|  | irq_enable(cfg->spi_irq); | 
|  |  | 
|  | ret = spi_context_cs_configure_all(&data->ctx); | 
|  | if (ret) { | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | spi_context_unlock_unconditionally(&data->ctx); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static DEVICE_API(spi, spi_it8xxx2_driver_api) = { | 
|  | .transceive = it8xxx2_transceive, | 
|  | .release = it8xxx2_release, | 
|  |  | 
|  | #ifdef CONFIG_SPI_ASYNC | 
|  | .transceive_async = it8xxx2_transceive_async, | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | #define SPI_IT8XXX2_INIT(n)                                                                        \ | 
|  | PINCTRL_DT_INST_DEFINE(n);                                                                 \ | 
|  | static const struct spi_it8xxx2_config spi_it8xxx2_cfg_##n = {                             \ | 
|  | .base = DT_INST_REG_ADDR(n),                                                       \ | 
|  | .pcfg = PINCTRL_DT_INST_DEV_CONFIG_GET(n),                                         \ | 
|  | .spi_irq = DT_INST_IRQ(n, irq),                                                    \ | 
|  | };                                                                                         \ | 
|  | \ | 
|  | static struct spi_it8xxx2_data spi_it8xxx2_data_##n = {                                    \ | 
|  | SPI_CONTEXT_INIT_LOCK(spi_it8xxx2_data_##n, ctx),                                  \ | 
|  | SPI_CONTEXT_INIT_SYNC(spi_it8xxx2_data_##n, ctx),                                  \ | 
|  | };                                                                                         \ | 
|  | \ | 
|  | DEVICE_DT_INST_DEFINE(n, &spi_it8xxx2_init, NULL, &spi_it8xxx2_data_##n,                   \ | 
|  | &spi_it8xxx2_cfg_##n, POST_KERNEL,                                   \ | 
|  | CONFIG_KERNEL_INIT_PRIORITY_DEVICE, &spi_it8xxx2_driver_api); | 
|  |  | 
|  | DT_INST_FOREACH_STATUS_OKAY(SPI_IT8XXX2_INIT) |