| /* |
| * Copyright 2017 NXP |
| * |
| * Redistribution and use in source and binary forms, with or without modification, |
| * are permitted provided that the following conditions are met: |
| * |
| * o Redistributions of source code must retain the above copyright notice, this list |
| * of conditions and the following disclaimer. |
| * |
| * o Redistributions in binary form must reproduce the above copyright notice, this |
| * list of conditions and the following disclaimer in the documentation and/or |
| * other materials provided with the distribution. |
| * |
| * o Neither the name of the copyright holder nor the names of its |
| * contributors may be used to endorse or promote products derived from this |
| * software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND |
| * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED |
| * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE |
| * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR |
| * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES |
| * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; |
| * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON |
| * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS |
| * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| */ |
| |
| #include "fsl_semc.h" |
| |
| /******************************************************************************* |
| * Definitions |
| ******************************************************************************/ |
| |
| /*! @brief Define macros for SEMC driver. */ |
| #define SEMC_IPCOMMANDDATASIZEBYTEMAX (4U) |
| #define SEMC_IPCOMMANDMAGICKEY (0xA55A) |
| #define SEMC_IOCR_PINMUXBITWIDTH (0x3U) |
| #define SEMC_IOCR_NAND_CE (4U) |
| #define SEMC_IOCR_NOR_CE (5U) |
| #define SEMC_IOCR_NOR_CE_A8 (2U) |
| #define SEMC_IOCR_PSRAM_CE (6U) |
| #define SEMC_IOCR_PSRAM_CE_A8 (3U) |
| #define SEMC_IOCR_DBI_CSX (7U) |
| #define SEMC_IOCR_DBI_CSX_A8 (4U) |
| #define SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE (24U) |
| #define SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHMAX (28U) |
| #define SEMC_BMCR0_TYPICAL_WQOS (5U) |
| #define SEMC_BMCR0_TYPICAL_WAGE (8U) |
| #define SEMC_BMCR0_TYPICAL_WSH (0x40U) |
| #define SEMC_BMCR0_TYPICAL_WRWS (0x10U) |
| #define SEMC_BMCR1_TYPICAL_WQOS (5U) |
| #define SEMC_BMCR1_TYPICAL_WAGE (8U) |
| #define SEMC_BMCR1_TYPICAL_WPH (0x60U) |
| #define SEMC_BMCR1_TYPICAL_WBR (0x40U) |
| #define SEMC_BMCR1_TYPICAL_WRWS (0x24U) |
| #define SEMC_STARTADDRESS (0x80000000U) |
| #define SEMC_ENDADDRESS (0xDFFFFFFFU) |
| #define SEMC_BR_MEMSIZE_MIN (4) |
| #define SEMC_BR_MEMSIZE_OFFSET (2) |
| #define SEMC_BR_MEMSIZE_MAX (4 * 1024 * 1024) |
| #define SEMC_SDRAM_MODESETCAL_OFFSET (4) |
| #define SEMC_BR_REG_NUM (9) |
| #define SEMC_BYTE_NUMBIT (4) |
| /******************************************************************************* |
| * Prototypes |
| ******************************************************************************/ |
| /*! |
| * @brief Get instance number for SEMC module. |
| * |
| * @param base SEMC peripheral base address |
| */ |
| static uint32_t SEMC_GetInstance(SEMC_Type *base); |
| |
| /*! |
| * @brief Covert the input memory size to internal register set value. |
| * |
| * @param base SEMC peripheral base address |
| * @param size_kbytes SEMC memory size in unit of kbytes. |
| * @param sizeConverted SEMC converted memory size to 0 ~ 0x1F. |
| * @return Execution status. |
| */ |
| static status_t SEMC_CovertMemorySize(SEMC_Type *base, uint32_t size_kbytes, uint8_t *sizeConverted); |
| |
| /*! |
| * @brief Covert the external timing nanosecond to internal clock cycle. |
| * |
| * @param time_ns SEMC external time interval in unit of nanosecond. |
| * @param clkSrc_Hz SEMC clock source frequency. |
| * @return The changed internal clock cycle. |
| */ |
| static uint8_t SEMC_ConvertTiming(uint32_t time_ns, uint32_t clkSrc_Hz); |
| |
| /*! |
| * @brief Configure IP command. |
| * |
| * @param base SEMC peripheral base address. |
| * @param size_bytes SEMC IP command data size. |
| * @return Execution status. |
| */ |
| static status_t SEMC_ConfigureIPCommand(SEMC_Type *base, uint8_t size_bytes); |
| |
| /*! |
| * @brief Check if the IP command has finished. |
| * |
| * @param base SEMC peripheral base address. |
| * @return Execution status. |
| */ |
| static status_t SEMC_IsIPCommandDone(SEMC_Type *base); |
| |
| /******************************************************************************* |
| * Variables |
| ******************************************************************************/ |
| |
| #if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) |
| /*! @brief Pointers to SEMC clocks for each instance. */ |
| static const clock_ip_name_t s_semcClock[FSL_FEATURE_SOC_SEMC_COUNT] = SEMC_CLOCKS; |
| #endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */ |
| |
| /*! @brief Pointers to SEMC bases for each instance. */ |
| static SEMC_Type *const s_semcBases[] = SEMC_BASE_PTRS; |
| /******************************************************************************* |
| * Code |
| ******************************************************************************/ |
| static uint32_t SEMC_GetInstance(SEMC_Type *base) |
| { |
| uint32_t instance; |
| |
| /* Find the instance index from base address mappings. */ |
| for (instance = 0; instance < ARRAY_SIZE(s_semcBases); instance++) |
| { |
| if (s_semcBases[instance] == base) |
| { |
| break; |
| } |
| } |
| |
| assert(instance < ARRAY_SIZE(s_semcBases)); |
| |
| return instance; |
| } |
| |
| static status_t SEMC_CovertMemorySize(SEMC_Type *base, uint32_t size_kbytes, uint8_t *sizeConverted) |
| { |
| assert(sizeConverted); |
| uint32_t memsize; |
| |
| if ((size_kbytes < SEMC_BR_MEMSIZE_MIN) || (size_kbytes > SEMC_BR_MEMSIZE_MAX)) |
| { |
| return kStatus_SEMC_InvalidMemorySize; |
| } |
| |
| *sizeConverted = 0; |
| memsize = size_kbytes / 8; |
| while (memsize) |
| { |
| memsize >>= 1; |
| (*sizeConverted)++; |
| } |
| return kStatus_Success; |
| } |
| |
| static uint8_t SEMC_ConvertTiming(uint32_t time_ns, uint32_t clkSrc_Hz) |
| { |
| assert(clkSrc_Hz); |
| |
| uint8_t clockCycles = 0; |
| uint32_t tClk_us; |
| |
| clkSrc_Hz /= 1000000; |
| tClk_us = 1000000 / clkSrc_Hz; |
| |
| while (tClk_us * clockCycles < (time_ns * 1000)) |
| { |
| clockCycles++; |
| } |
| |
| return clockCycles; |
| } |
| |
| static status_t SEMC_ConfigureIPCommand(SEMC_Type *base, uint8_t size_bytes) |
| { |
| if ((size_bytes > SEMC_IPCOMMANDDATASIZEBYTEMAX) || (!size_bytes)) |
| { |
| return kStatus_SEMC_InvalidIpcmdDataSize; |
| } |
| |
| /* Set data size. */ |
| /* Note: It is better to set data size as the device data port width when transfering |
| * device command data. but for device memory data transfer, it can be set freely. |
| * Note: If the data size is greater than data port width, for example, datsz = 4, data port = 16bit, |
| * then the 4-byte data transfer will be split into two 2-byte transfer, the slave address |
| * will be switched automatically according to connected device type*/ |
| base->IPCR1 = SEMC_IPCR1_DATSZ(size_bytes); |
| if (size_bytes < 4) |
| { |
| base->IPCR2 |= SEMC_IPCR2_BM3_MASK; |
| } |
| if (size_bytes < 3) |
| { |
| base->IPCR2 |= SEMC_IPCR2_BM2_MASK; |
| } |
| if (size_bytes < 2) |
| { |
| base->IPCR2 |= SEMC_IPCR2_BM1_MASK; |
| } |
| return kStatus_Success; |
| } |
| |
| static status_t SEMC_IsIPCommandDone(SEMC_Type *base) |
| { |
| /* Poll status bit till command is done*/ |
| while (!(base->INTR & SEMC_INTR_IPCMDDONE_MASK)) |
| {}; |
| |
| /* Clear status bit */ |
| base->INTR |= SEMC_INTR_IPCMDDONE_MASK; |
| |
| /* Check error status */ |
| if (base->INTR & SEMC_INTR_IPCMDERR_MASK) |
| { |
| base->INTR |= SEMC_INTR_IPCMDERR_MASK; |
| return kStatus_SEMC_IpCommandExecutionError; |
| } |
| |
| return kStatus_Success; |
| } |
| |
| void SEMC_GetDefaultConfig(semc_config_t *config) |
| { |
| assert(config); |
| |
| semc_axi_queueweight_t queueWeight; /*!< AXI queue weight. */ |
| semc_queuea_weight_t queueaWeight; |
| semc_queueb_weight_t queuebWeight; |
| |
| /* Get default settings. */ |
| config->dqsMode = kSEMC_Loopbackinternal; |
| config->cmdTimeoutCycles = 0; |
| config->busTimeoutCycles = 0x1F; |
| |
| /* Set a typical weight settings. */ |
| memset((void *)&queueWeight, 0, sizeof(semc_axi_queueweight_t)); |
| |
| queueaWeight.qos = SEMC_BMCR0_TYPICAL_WQOS; |
| queueaWeight.aging = SEMC_BMCR0_TYPICAL_WAGE; |
| queueaWeight.slaveHitSwith = SEMC_BMCR0_TYPICAL_WSH; |
| queueaWeight.slaveHitNoswitch = SEMC_BMCR0_TYPICAL_WRWS; |
| queuebWeight.qos = SEMC_BMCR1_TYPICAL_WQOS; |
| queuebWeight.aging = SEMC_BMCR1_TYPICAL_WAGE; |
| queuebWeight.slaveHitSwith = SEMC_BMCR1_TYPICAL_WRWS; |
| queuebWeight.weightPagehit = SEMC_BMCR1_TYPICAL_WPH; |
| queuebWeight.bankRotation = SEMC_BMCR1_TYPICAL_WBR; |
| |
| config->queueWeight.queueaWeight = &queueaWeight; |
| config->queueWeight.queuebWeight = &queuebWeight; |
| } |
| |
| void SEMC_Init(SEMC_Type *base, semc_config_t *configure) |
| { |
| assert(configure); |
| |
| uint8_t index = 0; |
| |
| #if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) |
| /* Un-gate sdram controller clock. */ |
| CLOCK_EnableClock(s_semcClock[SEMC_GetInstance(base)]); |
| #endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */ |
| |
| /* Initialize all BR to zero due to the default base address set. */ |
| for (index = 0; index < SEMC_BR_REG_NUM; index++) |
| { |
| base->BR[index] = 0; |
| } |
| |
| /* Software reset for SEMC internal logical . */ |
| base->MCR = SEMC_MCR_SWRST_MASK; |
| while (base->MCR & SEMC_MCR_SWRST_MASK) |
| { |
| } |
| |
| /* Configure, disable module first. */ |
| base->MCR |= SEMC_MCR_MDIS_MASK | SEMC_MCR_BTO(configure->busTimeoutCycles) | |
| SEMC_MCR_CTO(configure->cmdTimeoutCycles) | SEMC_MCR_DQSMD(configure->dqsMode); |
| |
| /* Configure Queue 0/1 for AXI bus. */ |
| if (configure->queueWeight.queueaWeight) |
| { |
| base->BMCR0 = (uint32_t)(configure->queueWeight.queueaWeight); |
| } |
| if (configure->queueWeight.queuebWeight) |
| { |
| base->BMCR1 = (uint32_t)(configure->queueWeight.queuebWeight); |
| } |
| /* Enable SEMC. */ |
| base->MCR &= ~SEMC_MCR_MDIS_MASK; |
| } |
| |
| void SEMC_Deinit(SEMC_Type *base) |
| { |
| /* Disable module. Check there is no pending command before disable module. */ |
| while (!(base->STS0 & SEMC_STS0_IDLE_MASK)) |
| { |
| ; |
| } |
| |
| base->MCR |= SEMC_MCR_MDIS_MASK | SEMC_MCR_SWRST_MASK; |
| |
| #if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) |
| /* Disable SDRAM clock. */ |
| CLOCK_DisableClock(s_semcClock[SEMC_GetInstance(base)]); |
| #endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */ |
| } |
| |
| status_t SEMC_ConfigureSDRAM(SEMC_Type *base, semc_sdram_cs_t cs, semc_sdram_config_t *config, uint32_t clkSrc_Hz) |
| { |
| assert(config); |
| assert(clkSrc_Hz); |
| assert(config->refreshBurstLen); |
| |
| uint8_t memsize; |
| status_t result = kStatus_Success; |
| uint16_t prescale = config->tPrescalePeriod_Ns / 16 / (1000000000 / clkSrc_Hz); |
| uint16_t refresh; |
| uint16_t urgentRef; |
| uint16_t idle; |
| uint16_t mode; |
| |
| if ((config->address < SEMC_STARTADDRESS) || (config->address > SEMC_ENDADDRESS)) |
| { |
| return kStatus_SEMC_InvalidBaseAddress; |
| } |
| |
| if (config->csxPinMux == kSEMC_MUXA8) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| |
| if (prescale > 256) |
| { |
| return kStatus_SEMC_InvalidTimerSetting; |
| } |
| |
| refresh = config->refreshPeriod_nsPerRow / config->tPrescalePeriod_Ns; |
| urgentRef = config->refreshUrgThreshold / config->tPrescalePeriod_Ns; |
| idle = config->tIdleTimeout_Ns / config->tPrescalePeriod_Ns; |
| |
| uint32_t iocReg = base->IOCR & ~(SEMC_IOCR_PINMUXBITWIDTH << config->csxPinMux); |
| |
| /* Base control. */ |
| result = SEMC_CovertMemorySize(base, config->memsize_kbytes, &memsize); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| |
| base->BR[cs] = (config->address & SEMC_BR_BA_MASK) | SEMC_BR_MS(memsize) | SEMC_BR_VLD_MASK; |
| base->SDRAMCR0 = SEMC_SDRAMCR0_PS(config->portSize) | SEMC_SDRAMCR0_BL(config->burstLen) | |
| SEMC_SDRAMCR0_COL(config->columnAddrBitNum) | SEMC_SDRAMCR0_CL(config->casLatency); |
| /* IOMUX setting. */ |
| if (cs) |
| { |
| base->IOCR = iocReg | (cs << config->csxPinMux); |
| } |
| |
| base->IOCR &= ~SEMC_IOCR_MUX_A8_MASK; |
| |
| /* Timing setting. */ |
| base->SDRAMCR1 = SEMC_SDRAMCR1_PRE2ACT(SEMC_ConvertTiming(config->tPrecharge2Act_Ns, clkSrc_Hz)) | |
| SEMC_SDRAMCR1_ACT2RW(SEMC_ConvertTiming(config->tAct2ReadWrtie_Ns, clkSrc_Hz)) | |
| SEMC_SDRAMCR1_RFRC(SEMC_ConvertTiming(config->tRefreshRecovery_Ns, clkSrc_Hz)) | |
| SEMC_SDRAMCR1_WRC(SEMC_ConvertTiming(config->tWriteRecovery_Ns, clkSrc_Hz)) | |
| SEMC_SDRAMCR1_CKEOFF(SEMC_ConvertTiming(config->tCkeOff_Ns, clkSrc_Hz)) | |
| SEMC_SDRAMCR1_ACT2PRE(SEMC_ConvertTiming(config->tAct2Prechage_Ns, clkSrc_Hz)); |
| base->SDRAMCR2 = SEMC_SDRAMCR2_SRRC(SEMC_ConvertTiming(config->tSelfRefRecovery_Ns, clkSrc_Hz)) | |
| SEMC_SDRAMCR2_REF2REF(SEMC_ConvertTiming(config->tRefresh2Refresh_Ns, clkSrc_Hz)) | |
| SEMC_SDRAMCR2_ACT2ACT(SEMC_ConvertTiming(config->tAct2Act_Ns, clkSrc_Hz)) | |
| SEMC_SDRAMCR2_ITO(idle); |
| base->SDRAMCR3 = SEMC_SDRAMCR3_REBL(config->refreshBurstLen - 1) | |
| /* N * 16 * 1s / clkSrc_Hz = config->tPrescalePeriod_Ns */ |
| SEMC_SDRAMCR3_PRESCALE(prescale) | SEMC_SDRAMCR3_RT(refresh) | SEMC_SDRAMCR3_UT(urgentRef); |
| |
| SEMC->IPCR1 = 0x2; |
| SEMC->IPCR2 = 0; |
| |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_SDRAM, config->address, kSEMC_SDRAMCM_Prechargeall, 0, NULL); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_SDRAM, config->address, kSEMC_SDRAMCM_AutoRefresh, 0, NULL); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_SDRAM, config->address, kSEMC_SDRAMCM_AutoRefresh, 0, NULL); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_SDRAM, config->address, kSEMC_SDRAMCM_AutoRefresh, 0, NULL); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| /* Mode setting value. */ |
| mode = (uint16_t)config->burstLen | (uint16_t)(config->casLatency << SEMC_SDRAM_MODESETCAL_OFFSET); |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_SDRAM, config->address, kSEMC_SDRAMCM_Modeset, mode, NULL); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| |
| return kStatus_Success; |
| } |
| |
| status_t SEMC_ConfigureNAND(SEMC_Type *base, semc_nand_config_t *config, uint32_t clkSrc_Hz) |
| { |
| assert(config); |
| |
| uint8_t memsize; |
| status_t result; |
| |
| if ((config->axiAddress < SEMC_STARTADDRESS) || (config->axiAddress > SEMC_ENDADDRESS)) |
| { |
| return kStatus_SEMC_InvalidBaseAddress; |
| } |
| |
| if (config->cePinMux == kSEMC_MUXRDY) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| |
| uint32_t iocReg = base->IOCR & ~((SEMC_IOCR_PINMUXBITWIDTH << config->cePinMux) | SEMC_IOCR_MUX_RDY_MASK); |
| |
| /* Base control. */ |
| if (config->rdyactivePolarity == kSEMC_RdyActivehigh) |
| { |
| base->MCR |= SEMC_MCR_WPOL1_MASK; |
| } |
| else |
| { |
| base->MCR &= ~SEMC_MCR_WPOL1_MASK; |
| } |
| result = SEMC_CovertMemorySize(base, config->axiMemsize_kbytes, &memsize); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| base->BR[4] = (config->axiAddress & SEMC_BR_BA_MASK) | SEMC_BR_MS(memsize) | SEMC_BR_VLD_MASK; |
| |
| result = SEMC_CovertMemorySize(base, config->ipgMemsize_kbytes, &memsize); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| base->BR[8] = (config->ipgAddress & SEMC_BR_BA_MASK) | SEMC_BR_MS(memsize) | SEMC_BR_VLD_MASK; |
| |
| /* IOMUX setting. */ |
| if (config->cePinMux) |
| { |
| base->IOCR = iocReg | (SEMC_IOCR_NAND_CE << config->cePinMux); |
| } |
| else |
| { |
| base->IOCR = iocReg | (1U << config->cePinMux); |
| } |
| |
| base->NANDCR0 = SEMC_NANDCR0_PS(config->portSize) | SEMC_NANDCR0_BL(config->burstLen) | |
| SEMC_NANDCR0_EDO(config->edoModeEnabled) | SEMC_NANDCR0_COL(config->columnAddrBitNum); |
| |
| /* Timing setting. */ |
| base->NANDCR1 = SEMC_NANDCR1_CES(SEMC_ConvertTiming(config->tCeSetup_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR1_CEH(SEMC_ConvertTiming(config->tCeHold_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR1_WEL(SEMC_ConvertTiming(config->tWeLow_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR1_WEH(SEMC_ConvertTiming(config->tWeHigh_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR1_REL(SEMC_ConvertTiming(config->tReLow_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR1_REH(SEMC_ConvertTiming(config->tReHigh_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR1_TA(SEMC_ConvertTiming(config->tTurnAround_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR1_CEITV(SEMC_ConvertTiming(config->tCeInterval_Ns, clkSrc_Hz)); |
| base->NANDCR2 = SEMC_NANDCR2_TWHR(SEMC_ConvertTiming(config->tWehigh2Relow_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR2_TRHW(SEMC_ConvertTiming(config->tRehigh2Welow_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR2_TADL(SEMC_ConvertTiming(config->tAle2WriteStart_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR2_TRR(SEMC_ConvertTiming(config->tReady2Relow_Ns, clkSrc_Hz)) | |
| SEMC_NANDCR2_TWB(SEMC_ConvertTiming(config->tWehigh2Busy_Ns, clkSrc_Hz)); |
| base->NANDCR3 = config->arrayAddrOption; |
| return SEMC_ConfigureIPCommand(base, (config->portSize + 1)); |
| } |
| |
| status_t SEMC_ConfigureNOR(SEMC_Type *base, semc_nor_config_t *config, uint32_t clkSrc_Hz) |
| { |
| assert(config); |
| |
| uint8_t memsize; |
| status_t result; |
| |
| if ((config->address < SEMC_STARTADDRESS) || (config->address > SEMC_ENDADDRESS)) |
| { |
| return kStatus_SEMC_InvalidBaseAddress; |
| } |
| |
| uint32_t iocReg = base->IOCR & ~(SEMC_IOCR_PINMUXBITWIDTH << config->cePinMux); |
| uint32_t muxCe = (config->cePinMux == kSEMC_MUXRDY) ? |
| SEMC_IOCR_NOR_CE - 1 : |
| ((config->cePinMux == kSEMC_MUXA8) ? SEMC_IOCR_NOR_CE_A8 : SEMC_IOCR_NOR_CE); |
| |
| /* IOMUX setting. */ |
| base->IOCR = iocReg | (muxCe << config->cePinMux); |
| /* Address bit setting. */ |
| if (config->addrPortWidth > SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE) |
| { |
| if (config->addrPortWidth >= SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE + 1) |
| { |
| /* Address bit 24 (A24) */ |
| base->IOCR &= (uint32_t)~SEMC_IOCR_MUX_CSX0_MASK; |
| if (config->cePinMux == kSEMC_MUXCSX0) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| } |
| if (config->addrPortWidth >= SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE + 2) |
| { |
| /* Address bit 25 (A25) */ |
| base->IOCR &= (uint32_t)~SEMC_IOCR_MUX_CSX1_MASK; |
| if (config->cePinMux == kSEMC_MUXCSX1) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| } |
| if (config->addrPortWidth >= SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE + 3) |
| { |
| /* Address bit 26 (A26) */ |
| base->IOCR &= (uint32_t)~SEMC_IOCR_MUX_CSX2_MASK; |
| if (config->cePinMux == kSEMC_MUXCSX2) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| } |
| if (config->addrPortWidth >= SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE + 4) |
| { |
| if (config->addr27 == kSEMC_NORA27_MUXCSX3) |
| { |
| /* Address bit 27 (A27) */ |
| base->IOCR &= (uint32_t)~SEMC_IOCR_MUX_CSX3_MASK; |
| } |
| else if (config->addr27 == kSEMC_NORA27_MUXRDY) |
| { |
| base->IOCR |= SEMC_IOCR_MUX_RDY_MASK; |
| } |
| else |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| if (config->cePinMux == kSEMC_MUXCSX3) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| } |
| if (config->addrPortWidth > SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHMAX) |
| { |
| return kStatus_SEMC_InvalidAddressPortWidth; |
| } |
| } |
| |
| /* Base control. */ |
| if (config->rdyactivePolarity == kSEMC_RdyActivehigh) |
| { |
| base->MCR |= SEMC_MCR_WPOL0_MASK; |
| } |
| else |
| { |
| base->MCR &= ~SEMC_MCR_WPOL0_MASK; |
| } |
| result = SEMC_CovertMemorySize(base, config->memsize_kbytes, &memsize); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| base->BR[5] = (config->address & SEMC_BR_BA_MASK) | SEMC_BR_MS(memsize) | SEMC_BR_VLD_MASK; |
| base->NORCR0 = SEMC_NORCR0_PS(config->portSize) | SEMC_NORCR0_BL(config->burstLen) | |
| SEMC_NORCR0_AM(config->addrMode) | SEMC_NORCR0_ADVP(config->advActivePolarity) | |
| SEMC_NORCR0_COL(config->columnAddrBitNum); |
| |
| /* Timing setting. */ |
| base->NORCR1 = SEMC_NORCR1_CES(SEMC_ConvertTiming(config->tCeSetup_Ns, clkSrc_Hz)) | |
| SEMC_NORCR1_CEH(SEMC_ConvertTiming(config->tCeHold_Ns, clkSrc_Hz)) | |
| SEMC_NORCR1_AS(SEMC_ConvertTiming(config->tAddrSetup_Ns, clkSrc_Hz)) | |
| SEMC_NORCR1_AH(SEMC_ConvertTiming(config->tAddrHold_Ns, clkSrc_Hz)) | |
| SEMC_NORCR1_WEL(SEMC_ConvertTiming(config->tWeLow_Ns, clkSrc_Hz)) | |
| SEMC_NORCR1_WEH(SEMC_ConvertTiming(config->tWeHigh_Ns, clkSrc_Hz)) | |
| SEMC_NORCR1_REL(SEMC_ConvertTiming(config->tReLow_Ns, clkSrc_Hz)) | |
| SEMC_NORCR1_REH(SEMC_ConvertTiming(config->tReHigh_Ns, clkSrc_Hz)); |
| base->NORCR2 = SEMC_NORCR2_WDS(SEMC_ConvertTiming(config->tWriteSetup_Ns, clkSrc_Hz)) | |
| SEMC_NORCR2_WDH(SEMC_ConvertTiming(config->tWriteHold_Ns, clkSrc_Hz)) | |
| SEMC_NORCR2_TA(SEMC_ConvertTiming(config->tTurnAround_Ns, clkSrc_Hz)) | |
| SEMC_NORCR2_AWDH(SEMC_ConvertTiming(config->tAddr2WriteHold_Ns, clkSrc_Hz) + 1) | |
| SEMC_NORCR2_LC(config->latencyCount) | SEMC_NORCR2_RD(config->readCycle) | |
| SEMC_NORCR2_CEITV(SEMC_ConvertTiming(config->tCeInterval_Ns, clkSrc_Hz)); |
| |
| return SEMC_ConfigureIPCommand(base, (config->portSize + 1)); |
| } |
| |
| status_t SEMC_ConfigureSRAM(SEMC_Type *base, semc_sram_config_t *config, uint32_t clkSrc_Hz) |
| { |
| assert(config); |
| |
| uint8_t memsize; |
| status_t result = kStatus_Success; |
| |
| if ((config->address < SEMC_STARTADDRESS) || (config->address > SEMC_ENDADDRESS)) |
| { |
| return kStatus_SEMC_InvalidBaseAddress; |
| } |
| |
| uint32_t iocReg = base->IOCR & ~(SEMC_IOCR_PINMUXBITWIDTH << config->cePinMux); |
| uint32_t muxCe = (config->cePinMux == kSEMC_MUXRDY) ? |
| SEMC_IOCR_PSRAM_CE - 1 : |
| ((config->cePinMux == kSEMC_MUXA8) ? SEMC_IOCR_PSRAM_CE_A8 : SEMC_IOCR_PSRAM_CE); |
| |
| /* IOMUX setting. */ |
| base->IOCR = iocReg | (muxCe << config->cePinMux); |
| /* Address bit setting. */ |
| if (config->addrPortWidth > SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE) |
| { |
| if (config->addrPortWidth >= SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE + 1) |
| { |
| /* Address bit 24 (A24) */ |
| base->IOCR &= (uint32_t)~SEMC_IOCR_MUX_CSX0_MASK; |
| if (config->cePinMux == kSEMC_MUXCSX0) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| } |
| if (config->addrPortWidth >= SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE + 2) |
| { |
| /* Address bit 25 (A25) */ |
| base->IOCR &= (uint32_t)~SEMC_IOCR_MUX_CSX1_MASK; |
| if (config->cePinMux == kSEMC_MUXCSX1) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| } |
| if (config->addrPortWidth >= SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE + 3) |
| { |
| /* Address bit 26 (A26) */ |
| base->IOCR &= (uint32_t)~SEMC_IOCR_MUX_CSX2_MASK; |
| if (config->cePinMux == kSEMC_MUXCSX2) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| } |
| if (config->addrPortWidth >= SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHBASE + 4) |
| { |
| if (config->addr27 == kSEMC_NORA27_MUXCSX3) |
| { |
| /* Address bit 27 (A27) */ |
| base->IOCR &= (uint32_t)~SEMC_IOCR_MUX_CSX3_MASK; |
| } |
| else if (config->addr27 == kSEMC_NORA27_MUXRDY) |
| { |
| base->IOCR |= SEMC_IOCR_MUX_RDY_MASK; |
| } |
| else |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| |
| if (config->cePinMux == kSEMC_MUXCSX3) |
| { |
| return kStatus_SEMC_InvalidSwPinmuxSelection; |
| } |
| } |
| if (config->addrPortWidth > SEMC_NORFLASH_SRAM_ADDR_PORTWIDTHMAX) |
| { |
| return kStatus_SEMC_InvalidAddressPortWidth; |
| } |
| } |
| /* Base control. */ |
| result = SEMC_CovertMemorySize(base, config->memsize_kbytes, &memsize); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| base->BR[6] = (config->address & SEMC_BR_BA_MASK) | SEMC_BR_MS(memsize) | SEMC_BR_VLD_MASK; |
| base->SRAMCR0 = SEMC_SRAMCR0_PS(config->portSize) | SEMC_SRAMCR0_BL(config->burstLen) | |
| SEMC_SRAMCR0_AM(config->addrMode) | SEMC_SRAMCR0_ADVP(config->advActivePolarity) | |
| SEMC_SRAMCR0_COL_MASK; |
| |
| /* Timing setting. */ |
| base->SRAMCR1 = SEMC_SRAMCR1_CES(SEMC_ConvertTiming(config->tCeSetup_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR1_CEH(SEMC_ConvertTiming(config->tCeHold_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR1_AS(SEMC_ConvertTiming(config->tAddrSetup_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR1_AH(SEMC_ConvertTiming(config->tAddrHold_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR1_WEL(SEMC_ConvertTiming(config->tWeLow_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR1_WEH(SEMC_ConvertTiming(config->tWeHigh_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR1_REL(SEMC_ConvertTiming(config->tReLow_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR1_REH(SEMC_ConvertTiming(config->tReHigh_Ns, clkSrc_Hz)); |
| |
| base->SRAMCR2 = SEMC_SRAMCR2_WDS(SEMC_ConvertTiming(config->tWriteSetup_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR2_WDH(SEMC_ConvertTiming(config->tWriteHold_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR2_TA(SEMC_ConvertTiming(config->tTurnAround_Ns, clkSrc_Hz)) | |
| SEMC_SRAMCR2_AWDH(SEMC_ConvertTiming(config->tAddr2WriteHold_Ns, clkSrc_Hz) + 1) | |
| SEMC_SRAMCR2_LC(config->latencyCount) | SEMC_SRAMCR2_RD(config->readCycle) | |
| SEMC_SRAMCR2_CEITV(SEMC_ConvertTiming(config->tCeInterval_Ns, clkSrc_Hz)); |
| |
| return result; |
| } |
| |
| status_t SEMC_ConfigureDBI(SEMC_Type *base, semc_dbi_config_t *config, uint32_t clkSrc_Hz) |
| { |
| assert(config); |
| |
| uint8_t memsize; |
| status_t result; |
| |
| if ((config->address < SEMC_STARTADDRESS) || (config->address > SEMC_ENDADDRESS)) |
| { |
| return kStatus_SEMC_InvalidBaseAddress; |
| } |
| |
| uint32_t iocReg = base->IOCR & ~(SEMC_IOCR_PINMUXBITWIDTH << config->csxPinMux); |
| uint32_t muxCsx = (config->csxPinMux == kSEMC_MUXRDY) ? |
| SEMC_IOCR_DBI_CSX - 1 : |
| ((config->csxPinMux == kSEMC_MUXA8) ? SEMC_IOCR_DBI_CSX_A8 : SEMC_IOCR_DBI_CSX); |
| |
| /* IOMUX setting. */ |
| base->IOCR = iocReg | (muxCsx << config->csxPinMux); |
| /* Base control. */ |
| result = SEMC_CovertMemorySize(base, config->memsize_kbytes, &memsize); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| base->BR[7] = (config->address & SEMC_BR_BA_MASK) | SEMC_BR_MS(memsize) | SEMC_BR_VLD_MASK; |
| base->DBICR0 = |
| SEMC_DBICR0_PS(config->portSize) | SEMC_DBICR0_BL(config->burstLen) | SEMC_DBICR0_COL(config->columnAddrBitNum); |
| |
| /* Timing setting. */ |
| base->DBICR1 = SEMC_DBICR1_CES(SEMC_ConvertTiming(config->tCsxSetup_Ns, clkSrc_Hz)) | |
| SEMC_DBICR1_CEH(SEMC_ConvertTiming(config->tCsxHold_Ns, clkSrc_Hz)) | |
| SEMC_DBICR1_WEL(SEMC_ConvertTiming(config->tWexLow_Ns, clkSrc_Hz)) | |
| SEMC_DBICR1_WEH(SEMC_ConvertTiming(config->tWexHigh_Ns, clkSrc_Hz)) | |
| SEMC_DBICR1_REL(SEMC_ConvertTiming(config->tRdxLow_Ns, clkSrc_Hz)) | |
| SEMC_DBICR1_REH(SEMC_ConvertTiming(config->tRdxHigh_Ns, clkSrc_Hz)) | |
| SEMC_DBICR1_CEITV(SEMC_ConvertTiming(config->tCsxInterval_Ns, clkSrc_Hz)); |
| return SEMC_ConfigureIPCommand(base, (config->portSize + 1)); |
| } |
| |
| status_t SEMC_SendIPCommand( |
| SEMC_Type *base, semc_mem_type_t type, uint32_t address, uint16_t command, uint32_t write, uint32_t *read) |
| { |
| uint32_t cmdMode; |
| bool readCmd = false; |
| bool writeCmd = false; |
| status_t result; |
| |
| /* Clear status bit */ |
| base->INTR |= SEMC_INTR_IPCMDDONE_MASK; |
| /* Set address. */ |
| base->IPCR0 = address; |
| |
| /* Check command mode. */ |
| cmdMode = command & 0xFU; |
| switch (type) |
| { |
| case kSEMC_MemType_NAND: |
| readCmd = (cmdMode == kSEMC_NANDCM_AXICmdAddrRead) || (cmdMode == kSEMC_NANDCM_CommandAddressRead) || |
| (cmdMode == kSEMC_NANDCM_CommandRead) || (cmdMode == kSEMC_NANDCM_Read); |
| writeCmd = (cmdMode == kSEMC_NANDCM_AXICmdAddrWrite) || (cmdMode == kSEMC_NANDCM_CommandAddressWrite) || |
| (cmdMode == kSEMC_NANDCM_CommandWrite) || (cmdMode == kSEMC_NANDCM_Write); |
| break; |
| case kSEMC_MemType_NOR: |
| case kSEMC_MemType_8080: |
| readCmd = (cmdMode == kSEMC_NORDBICM_Read); |
| writeCmd = (cmdMode == kSEMC_NORDBICM_Write); |
| break; |
| case kSEMC_MemType_SRAM: |
| readCmd = (cmdMode == kSEMC_SRAMCM_ArrayRead) || (cmdMode == kSEMC_SRAMCM_RegRead); |
| writeCmd = (cmdMode == kSEMC_SRAMCM_ArrayWrite) || (cmdMode == kSEMC_SRAMCM_RegWrite); |
| break; |
| case kSEMC_MemType_SDRAM: |
| readCmd = (cmdMode == kSEMC_SDRAMCM_Read); |
| writeCmd = (cmdMode == kSEMC_SDRAMCM_Write) || (cmdMode == kSEMC_SDRAMCM_Modeset); |
| break; |
| default: |
| break; |
| } |
| |
| if (writeCmd) |
| { |
| /* Set data. */ |
| base->IPTXDAT = write; |
| } |
| |
| /* Set command code. */ |
| base->IPCMD = command | SEMC_IPCMD_KEY(SEMC_IPCOMMANDMAGICKEY); |
| /* Wait for command done. */ |
| result = SEMC_IsIPCommandDone(base); |
| if (result != kStatus_Success) |
| { |
| return result; |
| } |
| |
| if (readCmd) |
| { |
| /* Get the read data */ |
| *read = base->IPRXDAT; |
| } |
| |
| return kStatus_Success; |
| } |
| |
| status_t SEMC_IPCommandNandWrite(SEMC_Type *base, uint32_t address, uint8_t *data, uint32_t size_bytes) |
| { |
| assert(data); |
| |
| status_t result = kStatus_Success; |
| uint16_t ipCmd; |
| uint8_t dataSize = base->NANDCR0 & SEMC_NANDCR0_PS_MASK; |
| uint32_t tempData = 0; |
| |
| /* Write command built */ |
| ipCmd = SEMC_BuildNandIPCommand(0, kSEMC_NANDAM_ColumnRow, kSEMC_NANDCM_Write); |
| while (size_bytes >= SEMC_IPCOMMANDDATASIZEBYTEMAX) |
| { |
| /* Configure IP command data size. */ |
| SEMC_ConfigureIPCommand(base, SEMC_IPCOMMANDDATASIZEBYTEMAX); |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_NAND, address, ipCmd, *(uint32_t *)data, NULL); |
| if (result != kStatus_Success) |
| { |
| break; |
| } |
| |
| data += SEMC_IPCOMMANDDATASIZEBYTEMAX; |
| size_bytes -= SEMC_IPCOMMANDDATASIZEBYTEMAX; |
| } |
| |
| if ((result == kStatus_Success) && size_bytes) |
| { |
| SEMC_ConfigureIPCommand(base, size_bytes); |
| |
| while (size_bytes) |
| { |
| tempData |= ((uint32_t)*(data + size_bytes - 1) << ((size_bytes - 1) * SEMC_BYTE_NUMBIT)); |
| size_bytes--; |
| } |
| |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_NAND, address, ipCmd, tempData, NULL); |
| } |
| SEMC_ConfigureIPCommand(base, dataSize); |
| |
| return result; |
| } |
| |
| status_t SEMC_IPCommandNandRead(SEMC_Type *base, uint32_t address, uint8_t *data, uint32_t size_bytes) |
| { |
| assert(data); |
| |
| status_t result = kStatus_Success; |
| uint8_t dataSize = base->NANDCR0 & SEMC_NANDCR0_PS_MASK; |
| uint16_t ipCmd; |
| uint32_t tempData = 0; |
| |
| /* Configure IP command data size. */ |
| SEMC_ConfigureIPCommand(base, SEMC_IPCOMMANDDATASIZEBYTEMAX); |
| /* Read command built */ |
| ipCmd = SEMC_BuildNandIPCommand(0, kSEMC_NANDAM_ColumnRow, kSEMC_NANDCM_Read); |
| |
| while (size_bytes >= SEMC_IPCOMMANDDATASIZEBYTEMAX) |
| { |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_NAND, address, ipCmd, 0, (uint32_t *)data); |
| if (result != kStatus_Success) |
| { |
| break; |
| } |
| |
| data += SEMC_IPCOMMANDDATASIZEBYTEMAX; |
| size_bytes -= SEMC_IPCOMMANDDATASIZEBYTEMAX; |
| } |
| |
| if ((result == kStatus_Success) && size_bytes) |
| { |
| SEMC_ConfigureIPCommand(base, size_bytes); |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_NAND, address, ipCmd, 0, &tempData); |
| |
| while (size_bytes) |
| { |
| *(data + size_bytes) = (tempData >> (SEMC_BYTE_NUMBIT * (size_bytes - 1))) & 0xFFU; |
| size_bytes--; |
| } |
| } |
| |
| SEMC_ConfigureIPCommand(base, dataSize); |
| return result; |
| } |
| |
| status_t SEMC_IPCommandNorRead(SEMC_Type *base, uint32_t address, uint8_t *data, uint32_t size_bytes) |
| { |
| assert(data); |
| |
| uint32_t tempData = 0; |
| status_t result = kStatus_Success; |
| uint8_t dataSize = base->NORCR0 & SEMC_NORCR0_PS_MASK; |
| |
| /* Configure IP command data size. */ |
| SEMC_ConfigureIPCommand(base, SEMC_IPCOMMANDDATASIZEBYTEMAX); |
| |
| while (size_bytes >= SEMC_IPCOMMANDDATASIZEBYTEMAX) |
| { |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_NOR, address, kSEMC_NORDBICM_Read, 0, (uint32_t *)data); |
| if (result != kStatus_Success) |
| { |
| break; |
| } |
| |
| data += SEMC_IPCOMMANDDATASIZEBYTEMAX; |
| size_bytes -= SEMC_IPCOMMANDDATASIZEBYTEMAX; |
| } |
| |
| if ((result == kStatus_Success) && size_bytes) |
| { |
| SEMC_ConfigureIPCommand(base, size_bytes); |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_NOR, address, kSEMC_NORDBICM_Read, 0, &tempData); |
| while (size_bytes) |
| { |
| *(data + size_bytes) = (tempData >> (SEMC_BYTE_NUMBIT * (size_bytes - 1))) & 0xFFU; |
| size_bytes--; |
| } |
| } |
| |
| SEMC_ConfigureIPCommand(base, dataSize); |
| return result; |
| } |
| |
| status_t SEMC_IPCommandNorWrite(SEMC_Type *base, uint32_t address, uint8_t *data, uint32_t size_bytes) |
| { |
| assert(data); |
| |
| uint32_t tempData = 0; |
| status_t result = kStatus_Success; |
| uint8_t dataSize = base->NORCR0 & SEMC_NORCR0_PS_MASK; |
| |
| /* Write command built */ |
| while (size_bytes >= SEMC_IPCOMMANDDATASIZEBYTEMAX) |
| { |
| /* Configure IP command data size. */ |
| SEMC_ConfigureIPCommand(base, SEMC_IPCOMMANDDATASIZEBYTEMAX); |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_NOR, address, kSEMC_NORDBICM_Write, *(uint32_t *)data, NULL); |
| if (result != kStatus_Success) |
| { |
| break; |
| } |
| size_bytes -= SEMC_IPCOMMANDDATASIZEBYTEMAX; |
| data += SEMC_IPCOMMANDDATASIZEBYTEMAX; |
| } |
| |
| if ((result == kStatus_Success) && size_bytes) |
| { |
| SEMC_ConfigureIPCommand(base, size_bytes); |
| |
| while (size_bytes) |
| { |
| tempData |= ((uint32_t)*(data + size_bytes - 1) << ((size_bytes - 1) * SEMC_BYTE_NUMBIT)); |
| size_bytes--; |
| } |
| |
| result = SEMC_SendIPCommand(base, kSEMC_MemType_NOR, address, kSEMC_NORDBICM_Write, tempData, NULL); |
| } |
| SEMC_ConfigureIPCommand(base, dataSize); |
| |
| return result; |
| } |