| .. zephyr:board:: max32670evkit |
| |
| Overview |
| ******** |
| The MAX32670 evaluation kit (EV kit) provides a platform for evaluation capabilities |
| of the MAX32670. The MAX32670 is an ultra-low-power, cost-effective, highly reliable |
| 32-bit microcontroller that enables designs with complex sensor processing without |
| compromising battery life. It combines a flexible and versatile power management unit |
| with the powerful Arm® Cortex®-M4 core with floating point unit (FPU). |
| The MAX32670 also offers legacy designs an easy and cost optimal upgradepath |
| from 8-bit or 16-bit microcontrollers. |
| |
| The Zephyr port is running on the MAX32670 MCU. |
| |
| Hardware |
| ******** |
| |
| - MAX32670 MCU: |
| |
| - High-Efficiency Microcontroller for Low-Power, High-Reliability Devices |
| |
| - Arm Cortex-M4 Core with FPU up to 100MHz |
| - 384KB Flash Memory with Error Correction |
| - 160KB SRAM (128KB with ECC Enabled),Optionally Preserved in Lowest Power Modes |
| - 16KB Unified Cache with ECC |
| |
| - UART Bootloader |
| |
| - Dual- or Single-Supply Operation |
| - Ultra-Low 0.9V to 1.1V VCORE Supply Voltage |
| - Internal LDO Operation from 1.7V to 3.6V SingleSupply |
| |
| - Wide Operating Temperature: -40°C to +105°C |
| |
| - Flexible Clocking Schemes |
| |
| - Internal High-Speed 100MHz Oscillator |
| - Internal Low-Power 7.3728MHz and Ultra-Low-Power 80kHz Oscillators |
| - 16MHz to 32MHz Oscillator (External CrystalRequired) |
| - 32.768kHz Oscillator (External Crystal Required) |
| - External Clock Input for the Core |
| - External Clock Input for the LPUART and LPTMR |
| |
| - Power Management Maximizes Uptime for Battery Applications |
| |
| - 44μA/MHz Active at 0.9V up to 12MHz |
| - 50μA/MHz Active at 1.1V up to 100MHz |
| - 2.6μA Full Memory Retention Power in BACKUPMode at VDD = 1.8V |
| - 350nA Ultra-Low-Power RTC at VDD = 1.8V |
| - Wake from LPUART or LPTMR |
| |
| - Optimal Peripheral Mix Provides Platform Scalability |
| |
| - Up to 31 General-Purpose I/O Pins |
| - Up to Three SPI Master/Slave (up to 50MHz) |
| - Up to Three 4-Wire UART |
| - One Low-Power UART (LPUART) |
| - Up to Three I2C Master/Slave 3.4Mbps High Speed |
| - 8-Channel Standard DMA Controller |
| - Up to Four 32-Bit Timers (TMR) |
| - Up to Two Low-Power 32-Bit Timers (LPTMR) |
| - Two Windowed Watchdog Timers |
| - One I2S Slave for Digital Audio Interface |
| |
| - Security and Integrity |
| |
| - Available Secure Boot |
| - AES 128/192/256 Hardware Acceleration Engine |
| - 32-Bit CRC Acceleration Engine |
| |
| - Benefits and Features of MAX32670EVKIT: |
| |
| - USB 2.0 Micro B to Serial UART Bridge |
| - UART0 and UART3 Interface is Selectable Through On-Board Jumpers |
| - On-Board MAX32625PICO-Based Debugger |
| - Boot Load Enable Circuitry |
| - SPI and I2C Signals Accessed Through 0.1in Headers |
| - GPIOs and Miscellaneous Signals Accessed Through 0.1in Headers |
| - Board Power Provided by USB Port |
| - On-Board SIMO Regulator and LDO for IC and Peripherals |
| - Individual Power Measurement on all IC Rails Through Jumpers |
| - Two General-Purpose LED and One GeneralPurpose Pushbutton Switch |
| |
| Supported Features |
| ================== |
| |
| .. zephyr:board-supported-hw:: |
| |
| Connections and IOs |
| =================== |
| |
| +-----------+---------------+---------------+--------------------------------------------------------------------------------------------------+ |
| | Name | Name | Settings | Description | |
| +===========+===============+===============+==================================================================================================+ |
| | JP1 | P0_22 | | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | Open | | | Disconnects red LED from P0_22. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | Close | | | Connects red to P0_22. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | | |
| +-----------+---------------+---------------+--------------------------------------------------------------------------------------------------+ |
| | JP2 | P0_23 | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | Open | | | Disconnects green LED from P0_23. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | Close | | | Connects green LED to P0_23. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | | |
| +-----------+---------------+---------------+--------------------------------------------------------------------------------------------------+ |
| | JP3 | P0_20 | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | P0_26 | | 2-1 | | | Connects the USB to serial port P0_8 (UART0_RX). | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | 2-3 | | | Connects the USB to serial port P0_26 (LPUART0_RX). | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | | |
| +-----------+---------------+---------------+--------------------------------------------------------------------------------------------------+ |
| | JP4 | P0_9 | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | P0_27 | | 2-1 | | | Connects the USB to serial port P0_9 (UART0_TX). | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | 2-3 | | | Connects the USB to serial port P0_27 (LPUART0_TX). | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | | |
| +-----------+---------------+---------------+--------------------------------------------------------------------------------------------------+ |
| | JP5 | VDD | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | Open | | | Disconnects power to VDD. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | Close | | | Connects power to VDD. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | | |
| +-----------+---------------+---------------+--------------------------------------------------------------------------------------------------+ |
| | JP6 | VCORE | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | Open | | | Disconnects power to VCORE. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | Close | | | Connects power to VCORE. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | | |
| +-----------+---------------+---------------+--------------------------------------------------------------------------------------------------+ |
| | JP7 | SIMO RSEL2 | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | 1-2 | | | Sets output 2 of the SIMO regulator to 0.9V. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | 3-4 | | | Sets output 2 of the SIMO regulator to 1.0V. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | 5-6 | | | Sets output 2 of the SIMO regulator to 1.1V. | | |
| | | | +-----------+ | +-------------------------------------------------------------------------------+ | |
| | | | | | |
| +-----------+---------------+---------------+--------------------------------------------------------------------------------------------------+ |
| |
| Programming and Debugging |
| ************************* |
| |
| .. zephyr:board-supported-runners:: |
| |
| Flashing |
| ======== |
| |
| The MAX32670 EVKIT integrates a MAX32625PICO based debugger for DAPLink functionality. |
| |
| |
| Once the debug probe is connected to your host computer, then you can simply run the |
| ``west flash`` command to write a firmware image into flash. To perform a full erase, |
| pass the ``--erase`` option when executing ``west flash``. |
| |
| Debugging |
| ========= |
| |
| Please refer to the `Flashing`_ section and run the ``west debug`` command |
| instead of ``west flash``. |
| |
| References |
| ********** |
| |
| - `MAX32670EVKIT web page`_ |
| |
| .. _MAX32670EVKIT web page: |
| https://www.analog.com/en/design-center/evaluation-hardware-and-software/evaluation-boards-kits/max32670evkit.html |
