| .. zephyr:board:: ganymed_bob |
| |
| .. _ganymed_bob: |
| |
| Overview |
| ******** |
| |
| .. note:: |
| |
| All software for the Ganymed Break-Out-Board (BOB) is experimental and hardware availability |
| is restricted to the participants in the limited sampling program. |
| |
| The Ganymed board hardware provides support for the Ganymed sy1xx series IoT multicore |
| RISC-V SoC with optional sensor level. |
| |
| Hardware |
| ******** |
| |
| * 32-Bit RISC-V 1+8-core processor, up to 500MHz |
| |
| * 1x Data Acquisition Unit |
| * 8x Data Processing Unit |
| * Event Bus |
| * MicroDMA |
| |
| * 4096 KB Global SRAM |
| * 64 KB Secure SRAM |
| * 512 KB Global MRAM |
| * 512 KB Secure MRAM |
| * CLOCK |
| * Peripherals |
| |
| * :abbr:`32x GPIO (General Purpose Input Output)` |
| * :abbr:`4x TWIM (I2C-compatible two-wire interface with MicroDMA)` |
| * 4x I2S |
| * :abbr:`7x SPI (Serial Peripheral Interface with MicroDMA)` |
| * :abbr:`3x UART (Universal receiver-transmitter with MicroDMA)` |
| * :abbr:`1x TSN (Time sensitive networking ethernet MAC with MicroDMA)` |
| * 1x CAN-FD |
| * 3x ADC |
| * Power section for on-board power generation and power measurement (selectable) |
| |
| * USB type-C |
| * external 5V power source |
| * 40-pin JTAG connector (compatible to Olimex ARM-JTAG-OCD-H) |
| * USB over FTDI (connected to UART0) |
| * Header for all I/Os and configuration |
| |
| * Assembly options for the SoC |
| |
| * SY120-GBM - Generic Base Module without top level sensors |
| * SY120-GEN1 - Generic Module type 1 with top level sensors (see below) |
| |
| The ``ganymed-bob/sy120-gen1`` comes with additional on-board sensors. |
| |
| Supported Features |
| ================== |
| |
| .. zephyr:board-supported-hw:: |
| |
| For more detailed description please refer to `Ganymed BreakOut Board Documentation`_ |
| |
| |
| Programming and Testing |
| *********************** |
| |
| .. zephyr:board-supported-runners:: |
| |
| Building |
| ======== |
| |
| Applications for the ``ganymed_bob/sy120_gbm`` board can be |
| built and flashed in the usual way. See |
| :ref:`build_an_application` and :ref:`application_run` for more details on |
| building and running. |
| |
| Building the :zephyr:code-sample:`hello_world` sample: |
| |
| .. zephyr-app-commands:: |
| :tool: west |
| :zephyr-app: samples/hello_world |
| :board: ganymed_bob/sy120_gbm |
| :goals: build |
| :compact: |
| |
| |
| Flashing |
| ======== |
| |
| Test the Ganymed with a :zephyr:code-sample:`hello_world` sample. |
| |
| Flash the zephyr image: |
| |
| .. zephyr-app-commands:: |
| :tool: west |
| :zephyr-app: samples/hello_world |
| :goals: flash |
| :west-args: --serial /dev/ttyUSB0 |
| :compact: |
| |
| |
| Testing |
| ======= |
| |
| Then attach a serial console, ex. minicom / picocom / putty; Reset the target. |
| The sample output should be: |
| |
| .. code-block:: console |
| |
| Hello World! ganymed_bob/sy120_gbm |
| |
| |
| References |
| ********** |
| |
| .. target-notes:: |
| |
| .. _`Ganymed BreakOut Board Documentation`: https://docs.sensry.net/datasheets/sy120-bob/ |
