boards/arm/usb_kw24d512/doc/index.rst - third_party/github/zephyrproject-rtos/zephyr - Git at Google

 .. _usb_kw24d512:

 NXP USB-KW24D512
 ################

 Overview
 ********

 The USB-KW24D512 is an evaluation board in a convenient USB dongle
 form factor based on the NXP MKW24D512 System-in-Package (SiP) device
 (KW2xD wireless MCU series).
 MKW24D512 wireless MCU provides a low-power, compact device with
 integrated IEEE 802.15.4 radio. The board can be used as a packet sniffer,
 network node, border router or as a development board.

 Hardware
 ********

 - Kinetis KW2xD-2.4 GHz 802.15.4 Wireless Radio Microcontroller
   (50 MHz, 512 KB flash memory, 64 KB RAM, low-power, crystal-less USB)
 - USB Type A Connector
 - Two blue LEDs
 - One user push button
 - One reset button
 - Integrated PCB Folded F-type antenna
 - 10-pin (0.05”) JTAG debug port for target MCU

 For more information about the KW2xD SiP and USB-KW24D512 board:

 - `KW2xD Website`_
 - `KW2xD Datasheet`_
 - `KW2xD Reference Manual`_
 - `USB-KW24D512 Website`_
 - `USB-KW24D512 Hardware Reference Manual`_

 Supported Features
 ==================

 The USB-KW24D512 board configuration supports the following hardware features:

 +-----------+------------+-------------------------------------+
 | Interface | Controller | Driver/Component                    |
 +===========+============+=====================================+
 | NVIC      | on-chip    | nested vector interrupt controller  |
 +-----------+------------+-------------------------------------+
 | SYSTICK   | on-chip    | systick                             |
 +-----------+------------+-------------------------------------+
 | PINMUX    | on-chip    | pinmux                              |
 +-----------+------------+-------------------------------------+
 | GPIO      | on-chip    | gpio                                |
 +-----------+------------+-------------------------------------+
 | I2C       | on-chip    | i2c                                 |
 +-----------+------------+-------------------------------------+
 | SPI       | on-chip    | spi                                 |
 +-----------+------------+-------------------------------------+
 | WATCHDOG  | on-chip    | watchdog                            |
 +-----------+------------+-------------------------------------+
 | UART      | on-chip    | serial port-polling;                |
 |           |            | serial port-interrupt               |
 +-----------+------------+-------------------------------------+
 | FLASH     | on-chip    | soc flash                           |
 +-----------+------------+-------------------------------------+
 | USB       | on-chip    | USB device                          |
 +-----------+------------+-------------------------------------+
 | RNGA      | on-chip    | entropy;                            |
 |           |            | random                              |
 +-----------+------------+-------------------------------------+
 | FTFL      | on-chip    | flash programming                   |
 +-----------+------------+-------------------------------------+

 The default configuration can be found in the defconfig file:

 	``boards/arm/usb_kw24d512/usb_kw24d512_defconfig``

 Other hardware features are not currently supported by the port.

 Connections and IOs
 ===================

 The KW2xD SoC has five pairs of pinmux/gpio controllers.

 +-------+-----------------+--------------------------------------+
 | Name  | Function        | Usage                                |
 +=======+=================+======================================+
 | PTA1  | UART0_RX        | UART Console                         |
 +-------+-----------------+--------------------------------------+
 | PTA2  | UART0_TX        | UART Console                         |
 +-------+-----------------+--------------------------------------+
 | PTC4  | GPIO            | SW1                                  |
 +-------+-----------------+--------------------------------------+
 | PTD4  | GPIO            | Blue LED (D2)                        |
 +-------+-----------------+--------------------------------------+
 | PTD5  | GPIO            | Blue LED (D3)                        |
 +-------+-----------------+--------------------------------------+
 | PTB10 | SPI1_PCS0       | internal connected to MCR20A         |
 +-------+-----------------+--------------------------------------+
 | PTB11 | SPI1_SCK        | internal connected to MCR20A         |
 +-------+-----------------+--------------------------------------+
 | PTB16 | SPI1_SOUT       | internal connected to MCR20A         |
 +-------+-----------------+--------------------------------------+
 | PTB17 | SPI1_SIN        | internal connected to MCR20A         |
 +-------+-----------------+--------------------------------------+
 | PTB19 | GPIO            | internal connected to MCR20A (Reset) |
 +-------+-----------------+--------------------------------------+
 | PTB3  | GPIO            | internal connected to MCR20A (IRQ_B) |
 +-------+-----------------+--------------------------------------+
 | PTC0  | GPIO            | internal connected to MCR20A (GPIO5) |
 +-------+-----------------+--------------------------------------+

 System Clock
 ============

 USB-KW24D512 contains 32 MHz oscillator crystal, which is connected to the
 clock pins of the radio transceiver. The MCU is configured to
 use the 4 MHz external clock from the transceiver with the on-chip PLL
 to generate a 48 MHz system clock.

 Serial Port
 ===========

 The KW2xD SoC has three UARTs. One is configured and can be used for the
 console, but it uses the same pins as the JTAG interface and is only
 accessible via the JTAG SWD connector.

 USB
 ===

 The KW2xD SoC has a USB OTG (USBOTG) controller that supports both
 device and host functions. Only USB device function is supported in Zephyr
 at the moment. The USB-KW24D512 board has a USB Type A connector and
 can only be used in device mode.

 Programming and Debugging
 *************************

 Build and flash applications as usual (see :ref:`build_an_application` and
 :ref:`application_run` for more details).

 Configuring a Debug Probe
 =========================

 A debug probe is used for both flashing and debugging the board. This board is
 configured by default to use the :ref:`jlink-external-debug-probe`.

 :ref:`jlink-external-debug-probe`
 ---------------------------------

 Install the :ref:`jlink-debug-host-tools` and make sure they are in your search
 path.

 Attach a J-Link 10-pin connector to J1.

 Configuring a Console
 =====================

 The console is available using `Segger RTT`_.

 Connect a USB cable from your PC to J5.

 Once you have started a debug session, run telnet:

 .. code-block:: console

     Trying 127.0.0.1...
     Connected to localhost.
     Escape character is '^]'.
     SEGGER J-Link V6.44 - Real time terminal output
     SEGGER J-Link ARM V10.1, SN=600111924
     Process: JLinkGDBServerCLExe

 Flashing
 ========

 Here is an example for the :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: usb_kw24d512
    :goals: flash

 The Segger RTT console is only available during a debug session. Use ``attach``
 to start one:

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: usb_kw24d512
    :goals: attach

 Run telnet as shown earlier, and you should see the following message in the
 terminal:

 .. code-block:: console

    ***** Booting Zephyr OS v1.14.0-rc1 *****
    Hello World! usb_kw24d512

 Debugging
 =========

 Here is an example for the :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: usb_kw24d512
    :goals: debug

 Run telnet as shown earlier, step through the application in your debugger, and
 you should see the following message in the terminal:

 .. code-block:: console

    ***** Booting Zephyr OS v1.14.0-rc1 *****
    Hello World! usb_kw24d512

 .. _USB-KW24D512 Website:
    https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/kinetis-cortex-m-mcus/w-serieswireless-conn.m0-plus-m4/ieee-802.15.4-packet-sniffer-usb-dongle-form-factor:USB-KW24D512

 .. _USB-KW24D512 Hardware Reference Manual:
    https://www.nxp.com/webapp/Download?colCode=USB-KW2XHWRM

 .. _KW2xD Website:
    https://www.nxp.com/products/wireless/thread/kinetis-kw2xd-2.4-ghz-802.15.4-wireless-radio-microcontroller-mcu-based-on-arm-cortex-m4-core:KW2xD

 .. _KW2xD Datasheet:
    https://www.nxp.com/docs/en/data-sheet/MKW2xDxxx.pdf

 .. _KW2xD Reference Manual:
    https://www.nxp.com/webapp/Download?colCode=MKW2XDXXXRM

 .. _Segger RTT:
    https://www.segger.com/products/debug-probes/j-link/technology/about-real-time-transfer/
	.. _usb_kw24d512:

	NXP USB-KW24D512
	################

	Overview
	********

	The USB-KW24D512 is an evaluation board in a convenient USB dongle
	form factor based on the NXP MKW24D512 System-in-Package (SiP) device
	(KW2xD wireless MCU series).
	MKW24D512 wireless MCU provides a low-power, compact device with
	integrated IEEE 802.15.4 radio. The board can be used as a packet sniffer,
	network node, border router or as a development board.

	Hardware
	********

	- Kinetis KW2xD-2.4 GHz 802.15.4 Wireless Radio Microcontroller
	(50 MHz, 512 KB flash memory, 64 KB RAM, low-power, crystal-less USB)
	- USB Type A Connector
	- Two blue LEDs
	- One user push button
	- One reset button
	- Integrated PCB Folded F-type antenna
	- 10-pin (0.05”) JTAG debug port for target MCU

	For more information about the KW2xD SiP and USB-KW24D512 board:

	- `KW2xD Website`_
	- `KW2xD Datasheet`_
	- `KW2xD Reference Manual`_
	- `USB-KW24D512 Website`_
	- `USB-KW24D512 Hardware Reference Manual`_

	Supported Features
	==================

	The USB-KW24D512 board configuration supports the following hardware features:

	+-----------+------------+-------------------------------------+
	\| Interface \| Controller \| Driver/Component \|
	+===========+============+=====================================+
	\| NVIC \| on-chip \| nested vector interrupt controller \|
	+-----------+------------+-------------------------------------+
	\| SYSTICK \| on-chip \| systick \|
	+-----------+------------+-------------------------------------+
	\| PINMUX \| on-chip \| pinmux \|
	+-----------+------------+-------------------------------------+
	\| GPIO \| on-chip \| gpio \|
	+-----------+------------+-------------------------------------+
	\| I2C \| on-chip \| i2c \|
	+-----------+------------+-------------------------------------+
	\| SPI \| on-chip \| spi \|
	+-----------+------------+-------------------------------------+
	\| WATCHDOG \| on-chip \| watchdog \|
	+-----------+------------+-------------------------------------+
	\| UART \| on-chip \| serial port-polling; \|
	\| \| \| serial port-interrupt \|
	+-----------+------------+-------------------------------------+
	\| FLASH \| on-chip \| soc flash \|
	+-----------+------------+-------------------------------------+
	\| USB \| on-chip \| USB device \|
	+-----------+------------+-------------------------------------+
	\| RNGA \| on-chip \| entropy; \|
	\| \| \| random \|
	+-----------+------------+-------------------------------------+
	\| FTFL \| on-chip \| flash programming \|
	+-----------+------------+-------------------------------------+

	The default configuration can be found in the defconfig file:

	``boards/arm/usb_kw24d512/usb_kw24d512_defconfig``

	Other hardware features are not currently supported by the port.

	Connections and IOs
	===================

	The KW2xD SoC has five pairs of pinmux/gpio controllers.

	+-------+-----------------+--------------------------------------+
	\| Name \| Function \| Usage \|
	+=======+=================+======================================+
	\| PTA1 \| UART0_RX \| UART Console \|
	+-------+-----------------+--------------------------------------+
	\| PTA2 \| UART0_TX \| UART Console \|
	+-------+-----------------+--------------------------------------+
	\| PTC4 \| GPIO \| SW1 \|
	+-------+-----------------+--------------------------------------+
	\| PTD4 \| GPIO \| Blue LED (D2) \|
	+-------+-----------------+--------------------------------------+
	\| PTD5 \| GPIO \| Blue LED (D3) \|
	+-------+-----------------+--------------------------------------+
	\| PTB10 \| SPI1_PCS0 \| internal connected to MCR20A \|
	+-------+-----------------+--------------------------------------+
	\| PTB11 \| SPI1_SCK \| internal connected to MCR20A \|
	+-------+-----------------+--------------------------------------+
	\| PTB16 \| SPI1_SOUT \| internal connected to MCR20A \|
	+-------+-----------------+--------------------------------------+
	\| PTB17 \| SPI1_SIN \| internal connected to MCR20A \|
	+-------+-----------------+--------------------------------------+
	\| PTB19 \| GPIO \| internal connected to MCR20A (Reset) \|
	+-------+-----------------+--------------------------------------+
	\| PTB3 \| GPIO \| internal connected to MCR20A (IRQ_B) \|
	+-------+-----------------+--------------------------------------+
	\| PTC0 \| GPIO \| internal connected to MCR20A (GPIO5) \|
	+-------+-----------------+--------------------------------------+

	System Clock
	============

	USB-KW24D512 contains 32 MHz oscillator crystal, which is connected to the
	clock pins of the radio transceiver. The MCU is configured to
	use the 4 MHz external clock from the transceiver with the on-chip PLL
	to generate a 48 MHz system clock.

	Serial Port
	===========

	The KW2xD SoC has three UARTs. One is configured and can be used for the
	console, but it uses the same pins as the JTAG interface and is only
	accessible via the JTAG SWD connector.

	USB
	===

	The KW2xD SoC has a USB OTG (USBOTG) controller that supports both
	device and host functions. Only USB device function is supported in Zephyr
	at the moment. The USB-KW24D512 board has a USB Type A connector and
	can only be used in device mode.

	Programming and Debugging
	*************************

	Build and flash applications as usual (see :ref:`build_an_application` and
	:ref:`application_run` for more details).

	Configuring a Debug Probe
	=========================

	A debug probe is used for both flashing and debugging the board. This board is
	configured by default to use the :ref:`jlink-external-debug-probe`.

	:ref:`jlink-external-debug-probe`
	---------------------------------

	Install the :ref:`jlink-debug-host-tools` and make sure they are in your search
	path.

	Attach a J-Link 10-pin connector to J1.

	Configuring a Console
	=====================

	The console is available using `Segger RTT`_.

	Connect a USB cable from your PC to J5.

	Once you have started a debug session, run telnet:

	.. code-block:: console

	Trying 127.0.0.1...
	Connected to localhost.
	Escape character is '^]'.
	SEGGER J-Link V6.44 - Real time terminal output
	SEGGER J-Link ARM V10.1, SN=600111924
	Process: JLinkGDBServerCLExe

	Flashing
	========

	Here is an example for the :ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: usb_kw24d512
	:goals: flash

	The Segger RTT console is only available during a debug session. Use ``attach``
	to start one:

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: usb_kw24d512
	:goals: attach

	Run telnet as shown earlier, and you should see the following message in the
	terminal:

	.. code-block:: console

	*** Booting Zephyr OS v1.14.0-rc1 ***
	Hello World! usb_kw24d512

	Debugging
	=========

	Here is an example for the :ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: usb_kw24d512
	:goals: debug

	Run telnet as shown earlier, step through the application in your debugger, and
	you should see the following message in the terminal:

	.. code-block:: console

	*** Booting Zephyr OS v1.14.0-rc1 ***
	Hello World! usb_kw24d512

	.. _USB-KW24D512 Website:
	https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/kinetis-cortex-m-mcus/w-serieswireless-conn.m0-plus-m4/ieee-802.15.4-packet-sniffer-usb-dongle-form-factor:USB-KW24D512

	.. _USB-KW24D512 Hardware Reference Manual:
	https://www.nxp.com/webapp/Download?colCode=USB-KW2XHWRM

	.. _KW2xD Website:
	https://www.nxp.com/products/wireless/thread/kinetis-kw2xd-2.4-ghz-802.15.4-wireless-radio-microcontroller-mcu-based-on-arm-cortex-m4-core:KW2xD

	.. _KW2xD Datasheet:
	https://www.nxp.com/docs/en/data-sheet/MKW2xDxxx.pdf

	.. _KW2xD Reference Manual:
	https://www.nxp.com/webapp/Download?colCode=MKW2XDXXXRM

	.. _Segger RTT:
	https://www.segger.com/products/debug-probes/j-link/technology/about-real-time-transfer/