| # Kconfig.sht3xd - SHT3xD temperature and humidity sensor configuration options |
| |
| # |
| # Copyright (c) 2016 Intel Corporation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| menuconfig SHT3XD |
| bool |
| prompt "SHT3xD Temperature and Humidity Sensor" |
| depends on SENSOR && I2C |
| default n |
| help |
| Enable driver for SHT3xD temperature and humidity sensors. |
| |
| config SHT3XD_SYS_LOG_LEVEL |
| int "SHT3XD Log level" |
| depends on SYS_LOG && SHT3XD |
| default 0 |
| range 0 4 |
| help |
| Sets log level for SHT3XD driver. |
| Levels are: |
| |
| - 0 OFF: do not write |
| |
| - 1 ERROR: only write SYS_LOG_ERR |
| |
| - 2 WARNING: write SYS_LOG_WRN in addition to previous level |
| |
| - 3 INFO: write SYS_LOG_INF in addition to previous levels |
| |
| - 4 DEBUG: write SYS_LOG_DBG in addition to previous levels |
| |
| config SHT3XD_NAME |
| string |
| prompt "Driver name" |
| default "SHT3XD" |
| depends on SHT3XD |
| help |
| Device name with which the SHT3xD sensor is identified. |
| |
| config SHT3XD_INIT_PRIORITY |
| int |
| prompt "Init priority" |
| depends on SHT3XD |
| default 70 |
| help |
| Device driver initialization priority. |
| |
| choice |
| prompt "I2C address" |
| depends on SHT3XD |
| default SHT3XD_I2C_ADDR_A |
| help |
| I2C address of the SHT3xD sensor. |
| |
| config SHT3XD_I2C_ADDR_A |
| bool |
| prompt "0x44" |
| help |
| Choose this option if the ADDR pin is connected to VSS. |
| |
| config SHT3XD_I2C_ADDR_B |
| bool |
| prompt "0x45" |
| help |
| Choose this option if the ADDR pin is connected to VDD. |
| |
| endchoice |
| |
| config SHT3XD_I2C_MASTER_DEV_NAME |
| string |
| prompt "I2C master where SHT3xD is connected" |
| depends on SHT3XD |
| default "I2C_0" |
| help |
| Specify the device name of the I2C master device to which the |
| SHT3xD chip is connected. |
| |
| choice |
| prompt "Trigger mode" |
| depends on SHT3XD |
| default SHT3XD_TRIGGER_NONE |
| help |
| Specify the type of triggering to be used by the driver. |
| |
| config SHT3XD_TRIGGER_NONE |
| bool |
| prompt "No trigger" |
| |
| config SHT3XD_TRIGGER_GLOBAL_FIBER |
| bool |
| prompt "Use global fiber" |
| depends on GPIO && SYSTEM_WORKQUEUE |
| select SHT3XD_TRIGGER |
| |
| config SHT3XD_TRIGGER_OWN_FIBER |
| bool |
| prompt "Use own fiber" |
| depends on GPIO |
| select SHT3XD_TRIGGER |
| |
| endchoice |
| |
| config SHT3XD_TRIGGER |
| bool |
| depends on SHT3XD |
| |
| config SHT3XD_GPIO_DEV_NAME |
| string |
| prompt "GPIO device" |
| default "GPIO_0" |
| depends on SHT3XD && SHT3XD_TRIGGER |
| help |
| The device name of the GPIO device to which the SHT3xD interrupt |
| pins are connected. |
| |
| config SHT3XD_GPIO_PIN_NUM |
| int |
| prompt "Interrupt GPIO pin number" |
| default 0 |
| depends on SHT3XD && SHT3XD_TRIGGER |
| help |
| The number of the GPIO on which the interrupt signal from the |
| SHT3xD chip will be received. |
| |
| config SHT3XD_FIBER_PRIORITY |
| int |
| prompt "Fiber priority" |
| depends on SHT3XD && SHT3XD_TRIGGER_OWN_FIBER |
| default 10 |
| help |
| Priority of fiber used by the driver to handle interrupts. |
| |
| config SHT3XD_FIBER_STACK_SIZE |
| int |
| prompt "Fiber stack size" |
| depends on SHT3XD && SHT3XD_TRIGGER_OWN_FIBER |
| default 1024 |
| help |
| Stack size of fiber used by the driver to handle interrupts. |
| |
| choice |
| prompt "Measurement repeatability" |
| depends on SHT3XD |
| default SHT3XD_REPEATABILITY_HIGH |
| help |
| Repeatability modes differ with respect to measurement duration, |
| noise level and energy consumption. |
| |
| config SHT3XD_REPEATABILITY_LOW |
| bool |
| prompt "low" |
| |
| config SHT3XD_REPEATABILITY_MEDIUM |
| bool |
| prompt "medium" |
| |
| config SHT3XD_REPEATABILITY_HIGH |
| bool |
| prompt "high" |
| |
| endchoice |
| |
| choice |
| prompt "Measurements per second" |
| depends on SHT3XD |
| default SHT3XD_MPS_1 |
| help |
| Number of measurements per second. |
| |
| config SHT3XD_MPS_05 |
| bool |
| prompt "0.5" |
| |
| config SHT3XD_MPS_1 |
| bool |
| prompt "1" |
| |
| config SHT3XD_MPS_2 |
| bool |
| prompt "2" |
| |
| config SHT3XD_MPS_4 |
| bool |
| prompt "4" |
| |
| config SHT3XD_MPS_10 |
| bool |
| prompt "10" |
| |
| endchoice |
