| /* |
| * Copyright (c) 2024 Analog Devices, Inc. |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #define DT_DRV_COMPAT adi_max32_i2c |
| |
| #include <errno.h> |
| #include <zephyr/drivers/i2c.h> |
| #include <zephyr/drivers/pinctrl.h> |
| #include <zephyr/drivers/clock_control/adi_max32_clock_control.h> |
| #include <zephyr/irq.h> |
| |
| #if defined(CONFIG_I2C_MAX32_DMA) |
| #include <zephyr/drivers/dma.h> |
| #endif /* CONFIG_I2C_MAX32_DMA */ |
| |
| #include <wrap_max32_i2c.h> |
| |
| #define ADI_MAX32_I2C_INT_FL0_MASK 0x00FFFFFF |
| #define ADI_MAX32_I2C_INT_FL1_MASK 0x7 |
| |
| #define ADI_MAX32_I2C_STATUS_MASTER_BUSY BIT(5) |
| |
| #define I2C_RECOVER_MAX_RETRIES 3 |
| |
| #ifdef CONFIG_I2C_MAX32_DMA |
| struct max32_i2c_dma_config { |
| const struct device *dev; |
| const uint32_t channel; |
| const uint32_t slot; |
| }; |
| #endif /* CONFIG_I2C_MAX32_DMA */ |
| |
| /* Driver config */ |
| struct max32_i2c_config { |
| mxc_i2c_regs_t *regs; |
| const struct pinctrl_dev_config *pctrl; |
| const struct device *clock; |
| struct max32_perclk perclk; |
| uint32_t bitrate; |
| #if defined(CONFIG_I2C_TARGET) || defined(CONFIG_I2C_MAX32_INTERRUPT) |
| uint8_t irqn; |
| void (*irq_config_func)(const struct device *dev); |
| #endif |
| #ifdef CONFIG_I2C_MAX32_DMA |
| struct max32_i2c_dma_config tx_dma; |
| struct max32_i2c_dma_config rx_dma; |
| #endif /* CONFIG_I2C_MAX32_DMA */ |
| }; |
| |
| struct max32_i2c_data { |
| mxc_i2c_req_t req; |
| const struct device *dev; |
| struct k_sem lock; |
| uint8_t target_mode; |
| uint8_t flags; |
| #ifdef CONFIG_I2C_TARGET |
| struct i2c_target_config *target_cfg; |
| bool first_write; |
| #endif /* CONFIG_I2C_TARGET */ |
| uint32_t readb; |
| uint32_t written; |
| #if defined(CONFIG_I2C_MAX32_INTERRUPT) || defined(CONFIG_I2C_MAX32_DMA) |
| struct k_sem xfer; |
| int err; |
| #endif |
| }; |
| |
| static int api_configure(const struct device *dev, uint32_t dev_cfg) |
| { |
| int ret = 0; |
| const struct max32_i2c_config *const cfg = dev->config; |
| mxc_i2c_regs_t *i2c = cfg->regs; |
| |
| switch (I2C_SPEED_GET(dev_cfg)) { |
| case I2C_SPEED_STANDARD: /** I2C Standard Speed: 100 kHz */ |
| ret = MXC_I2C_SetFrequency(i2c, MXC_I2C_STD_MODE); |
| break; |
| |
| case I2C_SPEED_FAST: /** I2C Fast Speed: 400 kHz */ |
| ret = MXC_I2C_SetFrequency(i2c, MXC_I2C_FAST_SPEED); |
| break; |
| |
| #if defined(MXC_I2C_FASTPLUS_SPEED) |
| case I2C_SPEED_FAST_PLUS: /** I2C Fast Plus Speed: 1 MHz */ |
| ret = MXC_I2C_SetFrequency(i2c, MXC_I2C_FASTPLUS_SPEED); |
| break; |
| #endif |
| |
| #if defined(MXC_I2C_HIGH_SPEED) |
| case I2C_SPEED_HIGH: /** I2C High Speed: 3.4 MHz */ |
| ret = MXC_I2C_SetFrequency(i2c, MXC_I2C_HIGH_SPEED); |
| break; |
| #endif |
| |
| default: |
| /* Speed not supported */ |
| return -ENOTSUP; |
| } |
| |
| return ret; |
| } |
| |
| #ifdef CONFIG_I2C_TARGET |
| static int api_target_register(const struct device *dev, struct i2c_target_config *cfg) |
| { |
| const struct max32_i2c_config *config = dev->config; |
| struct max32_i2c_data *data = dev->data; |
| mxc_i2c_regs_t *i2c = config->regs; |
| int ret; |
| |
| data->target_cfg = cfg; |
| |
| ret = MXC_I2C_Init(i2c, 0, cfg->address); |
| if (ret == E_NO_ERROR) { |
| data->target_mode = 1; |
| irq_enable(config->irqn); |
| MXC_I2C_SlaveTransactionAsync(i2c, NULL); |
| } |
| |
| return ret == E_NO_ERROR ? 0 : E_FAIL; |
| } |
| |
| static int api_target_unregister(const struct device *dev, struct i2c_target_config *cfg) |
| { |
| const struct max32_i2c_config *config = dev->config; |
| struct max32_i2c_data *data = dev->data; |
| mxc_i2c_regs_t *i2c = config->regs; |
| |
| data->target_cfg = NULL; |
| data->target_mode = 0; |
| |
| #ifndef CONFIG_I2C_MAX32_INTERRUPT |
| irq_disable(config->irqn); |
| #endif |
| |
| return MXC_I2C_Init(i2c, 1, 0); |
| } |
| |
| static int i2c_max32_target_callback(const struct device *dev, mxc_i2c_regs_t *i2c, |
| mxc_i2c_slave_event_t event) |
| { |
| struct max32_i2c_data *data = dev->data; |
| const struct i2c_target_callbacks *target_cb = data->target_cfg->callbacks; |
| static uint8_t rxval, txval, rxcnt; |
| |
| switch (event) { |
| case MXC_I2C_EVT_MASTER_WR: |
| if (data->first_write && target_cb->write_requested) { |
| target_cb->write_requested(data->target_cfg); |
| data->first_write = false; |
| } |
| break; |
| case MXC_I2C_EVT_MASTER_RD: |
| break; |
| case MXC_I2C_EVT_RX_THRESH: |
| case MXC_I2C_EVT_OVERFLOW: |
| rxcnt = MXC_I2C_GetRXFIFOAvailable(i2c); |
| if (target_cb->write_received) { |
| while (rxcnt--) { |
| MXC_I2C_ReadRXFIFO(i2c, &rxval, 1); |
| target_cb->write_received(data->target_cfg, rxval); |
| } |
| } else { |
| MXC_I2C_ClearRXFIFO(i2c); |
| } |
| break; |
| case MXC_I2C_EVT_TX_THRESH: |
| case MXC_I2C_EVT_UNDERFLOW: |
| if (target_cb->read_requested) { |
| target_cb->read_requested(data->target_cfg, &txval); |
| MXC_I2C_WriteTXFIFO(i2c, &txval, 1); |
| } |
| if (target_cb->read_processed) { |
| target_cb->read_processed(data->target_cfg, &txval); |
| } |
| break; |
| case MXC_I2C_EVT_TRANS_COMP: |
| if (target_cb->stop) { |
| target_cb->stop(data->target_cfg); |
| } |
| data->first_write = true; |
| break; |
| } |
| |
| return 0; |
| } |
| #endif /* CONFIG_I2C_TARGET */ |
| |
| static int api_recover_bus(const struct device *dev) |
| { |
| int ret; |
| const struct max32_i2c_config *const cfg = dev->config; |
| mxc_i2c_regs_t *i2c = cfg->regs; |
| |
| ret = MXC_I2C_Recover(i2c, I2C_RECOVER_MAX_RETRIES); |
| |
| return ret; |
| } |
| |
| #ifndef CONFIG_I2C_MAX32_INTERRUPT |
| static int i2c_max32_transfer_sync(mxc_i2c_regs_t *i2c, struct max32_i2c_data *data) |
| { |
| uint32_t int_fl0, int_fl1; |
| uint32_t readb = 0; |
| mxc_i2c_req_t *req = &data->req; |
| |
| /* Wait for acknowledge */ |
| if (data->flags & (I2C_MSG_RESTART | I2C_MSG_READ)) { |
| do { |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| } while (!(int_fl0 & ADI_MAX32_I2C_INT_FL0_ADDR_ACK) && |
| !(int_fl0 & ADI_MAX32_I2C_INT_FL0_ERR)); |
| } |
| |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_ERR) { |
| return -EIO; |
| } |
| |
| while (req->tx_len > data->written) { |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_TX_THD) { |
| data->written += MXC_I2C_WriteTXFIFO(i2c, &req->tx_buf[data->written], |
| req->tx_len - data->written); |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_TX_THD, 0); |
| } |
| |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_ERR) { |
| return -EIO; |
| } |
| } |
| |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_DONE, 0); |
| Wrap_MXC_I2C_SetRxCount(i2c, req->rx_len); |
| while (req->rx_len > readb) { |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| if (int_fl0 & (ADI_MAX32_I2C_INT_FL0_RX_THD | ADI_MAX32_I2C_INT_FL0_DONE)) { |
| readb += MXC_I2C_ReadRXFIFO(i2c, &req->rx_buf[readb], req->rx_len - readb); |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_RX_THD, 0); |
| } |
| |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_ERR) { |
| return -EIO; |
| } |
| |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| if ((int_fl0 & ADI_MAX32_I2C_INT_FL0_DONE) && (req->rx_len > readb) && |
| MXC_I2C_GetRXFIFOAvailable(i2c) == 0) { |
| Wrap_MXC_I2C_SetRxCount(i2c, req->rx_len - readb); |
| Wrap_MXC_I2C_Restart(i2c); |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_DONE, 0); |
| i2c->fifo = (req->addr << 1) | 0x1; |
| } |
| } |
| |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_ERR) { |
| return -EIO; |
| } |
| |
| if (data->flags & I2C_MSG_STOP) { |
| MXC_I2C_Stop(i2c); |
| do { |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| } while (!(int_fl0 & ADI_MAX32_I2C_INT_FL0_STOP)); |
| } |
| |
| if (req->rx_len) { |
| do { |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| } while (!(int_fl0 & ADI_MAX32_I2C_INT_FL0_DONE)); |
| } else { |
| while (Wrap_MXC_I2C_GetTxFIFOLevel(i2c) > 0) { |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| } |
| } |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_MASK, ADI_MAX32_I2C_INT_FL1_MASK); |
| |
| return 0; |
| } |
| #endif /* CONFIG_I2C_MAX32_INTERRUPT */ |
| |
| #if defined(CONFIG_I2C_MAX32_DMA) |
| static void i2c_max32_dma_callback(const struct device *dev, void *arg, uint32_t channel, |
| int status) |
| { |
| struct max32_i2c_data *data = arg; |
| const struct device *i2c_dev = data->dev; |
| const struct max32_i2c_config *const cfg = i2c_dev->config; |
| |
| if (status < 0) { |
| data->err = -EIO; |
| } else { |
| if (data->req.restart) { |
| Wrap_MXC_I2C_Restart(cfg->regs); |
| } else { |
| Wrap_MXC_I2C_Stop(cfg->regs); |
| } |
| } |
| } |
| |
| static int i2c_max32_tx_dma_load(const struct device *dev, struct i2c_msg *msg) |
| { |
| int ret; |
| const struct max32_i2c_config *config = dev->config; |
| struct max32_i2c_data *data = dev->data; |
| struct dma_config dma_cfg = {0}; |
| struct dma_block_config dma_blk = {0}; |
| |
| dma_cfg.channel_direction = MEMORY_TO_PERIPHERAL; |
| dma_cfg.dma_callback = i2c_max32_dma_callback; |
| dma_cfg.user_data = (void *)data; |
| dma_cfg.dma_slot = config->tx_dma.slot; |
| dma_cfg.block_count = 1; |
| dma_cfg.source_data_size = 1U; |
| dma_cfg.source_burst_length = 1U; |
| dma_cfg.dest_data_size = 1U; |
| dma_cfg.head_block = &dma_blk; |
| dma_blk.block_size = msg->len; |
| dma_blk.source_addr_adj = DMA_ADDR_ADJ_INCREMENT; |
| dma_blk.source_address = (uint32_t)msg->buf; |
| |
| ret = dma_config(config->tx_dma.dev, config->tx_dma.channel, &dma_cfg); |
| if (ret < 0) { |
| return ret; |
| } |
| |
| return dma_start(config->tx_dma.dev, config->tx_dma.channel); |
| } |
| |
| static int i2c_max32_rx_dma_load(const struct device *dev, struct i2c_msg *msg) |
| { |
| int ret; |
| const struct max32_i2c_config *config = dev->config; |
| struct max32_i2c_data *data = dev->data; |
| struct dma_config dma_cfg = {0}; |
| struct dma_block_config dma_blk = {0}; |
| |
| dma_cfg.channel_direction = PERIPHERAL_TO_MEMORY; |
| dma_cfg.dma_callback = i2c_max32_dma_callback; |
| dma_cfg.user_data = (void *)data; |
| dma_cfg.dma_slot = config->rx_dma.slot; |
| dma_cfg.block_count = 1; |
| dma_cfg.source_data_size = 1U; |
| dma_cfg.source_burst_length = 1U; |
| dma_cfg.dest_data_size = 1U; |
| dma_cfg.head_block = &dma_blk; |
| dma_blk.block_size = msg->len; |
| dma_blk.dest_addr_adj = DMA_ADDR_ADJ_INCREMENT; |
| dma_blk.dest_address = (uint32_t)msg->buf; |
| |
| ret = dma_config(config->rx_dma.dev, config->rx_dma.channel, &dma_cfg); |
| if (ret < 0) { |
| return ret; |
| } |
| |
| return dma_start(config->rx_dma.dev, config->rx_dma.channel); |
| } |
| |
| static int i2c_max32_transfer_dma(const struct device *dev, struct i2c_msg *msgs, uint8_t num_msgs, |
| uint16_t target_address) |
| { |
| int ret = 0; |
| const struct max32_i2c_config *const cfg = dev->config; |
| struct max32_i2c_data *data = dev->data; |
| mxc_i2c_regs_t *i2c = cfg->regs; |
| uint8_t target_rw; |
| unsigned int i = 0; |
| |
| k_sem_take(&data->lock, K_FOREVER); |
| |
| MXC_I2C_SetRXThreshold(i2c, 1); |
| MXC_I2C_SetTXThreshold(i2c, 2); |
| MXC_I2C_ClearTXFIFO(i2c); |
| MXC_I2C_ClearRXFIFO(i2c); |
| |
| for (i = 0; i < num_msgs; i++) { |
| data->req.restart = !(msgs[i].flags & I2C_MSG_STOP); |
| if (msgs[i].flags & I2C_MSG_READ) { |
| target_rw = (target_address << 1) | 0x1; |
| MXC_I2C_WriteTXFIFO(i2c, &target_rw, 1); |
| Wrap_MXC_I2C_SetRxCount(i2c, msgs[i].len); |
| ret = i2c_max32_rx_dma_load(dev, &msgs[i]); |
| if (ret < 0) { |
| break; |
| } |
| |
| MXC_I2C_EnableInt( |
| i2c, ADI_MAX32_I2C_INT_EN0_DONE | ADI_MAX32_I2C_INT_EN0_ERR, 0); |
| i2c->dma |= ADI_MAX32_I2C_DMA_RX_EN; |
| } else { |
| target_rw = (target_address << 1) & ~0x1; |
| MXC_I2C_WriteTXFIFO(i2c, &target_rw, 1); |
| ret = i2c_max32_tx_dma_load(dev, &msgs[i]); |
| if (ret < 0) { |
| break; |
| } |
| |
| MXC_I2C_EnableInt( |
| i2c, ADI_MAX32_I2C_INT_EN0_DONE | ADI_MAX32_I2C_INT_EN0_ERR, 0); |
| i2c->dma |= ADI_MAX32_I2C_DMA_TX_EN; |
| } |
| data->err = 0; |
| |
| Wrap_MXC_I2C_Start(i2c); |
| ret = k_sem_take(&data->xfer, K_FOREVER); |
| Wrap_MXC_I2C_SetIntEn(i2c, 0, 0); |
| i2c->dma &= ~(ADI_MAX32_I2C_DMA_TX_EN | ADI_MAX32_I2C_DMA_RX_EN); |
| |
| if (data->err) { |
| ret = data->err; |
| } |
| if (ret) { |
| MXC_I2C_Stop(i2c); |
| dma_stop(cfg->tx_dma.dev, cfg->tx_dma.channel); |
| dma_stop(cfg->rx_dma.dev, cfg->rx_dma.channel); |
| } |
| } |
| |
| k_sem_give(&data->lock); |
| |
| return ret; |
| } |
| #endif /* CONFIG_I2C_MAX32_DMA */ |
| |
| #ifdef CONFIG_I2C_MAX32_INTERRUPT |
| static int i2c_max32_transfer(const struct device *dev, struct i2c_msg *msgs, uint8_t num_msgs, |
| uint16_t target_address) |
| { |
| int ret = 0; |
| const struct max32_i2c_config *const cfg = dev->config; |
| struct max32_i2c_data *data = dev->data; |
| mxc_i2c_regs_t *i2c = cfg->regs; |
| mxc_i2c_req_t *req = &data->req; |
| uint8_t target_rw; |
| unsigned int i = 0; |
| |
| req->i2c = i2c; |
| req->addr = target_address; |
| |
| k_sem_take(&data->lock, K_FOREVER); |
| |
| MXC_I2C_ClearRXFIFO(i2c); |
| MXC_I2C_ClearTXFIFO(i2c); |
| MXC_I2C_SetRXThreshold(i2c, 1); |
| |
| /* First message should always begin with a START condition */ |
| msgs[0].flags |= I2C_MSG_RESTART; |
| |
| for (i = 0; i < num_msgs; i++) { |
| if (msgs[i].flags & I2C_MSG_READ) { |
| req->rx_buf = (unsigned char *)msgs[i].buf; |
| req->rx_len = msgs[i].len; |
| req->tx_buf = NULL; |
| req->tx_len = 0; |
| target_rw = (target_address << 1) | 0x1; |
| } else { |
| req->tx_buf = (unsigned char *)msgs[i].buf; |
| req->tx_len = msgs[i].len; |
| req->rx_buf = NULL; |
| req->rx_len = 0; |
| target_rw = (target_address << 1) & ~0x1; |
| } |
| |
| /* |
| * If previous message ends with a STOP condition, this message |
| * should begin with a START |
| */ |
| if (i > 0) { |
| if ((msgs[i - 1].flags & (I2C_MSG_STOP | I2C_MSG_READ))) { |
| msgs[i].flags |= I2C_MSG_RESTART; |
| } |
| } |
| |
| data->flags = msgs[i].flags; |
| data->readb = 0; |
| data->written = 0; |
| data->err = 0; |
| |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_MASK, ADI_MAX32_I2C_INT_FL1_MASK); |
| MXC_I2C_EnableInt(i2c, ADI_MAX32_I2C_INT_EN0_ERR, 0); |
| Wrap_MXC_I2C_SetRxCount(i2c, req->rx_len); |
| if ((data->flags & I2C_MSG_RESTART)) { |
| MXC_I2C_EnableInt(i2c, ADI_MAX32_I2C_INT_EN0_ADDR_ACK, 0); |
| MXC_I2C_Start(i2c); |
| Wrap_MXC_I2C_WaitForRestart(i2c); |
| MXC_I2C_WriteTXFIFO(i2c, &target_rw, 1); |
| } else { |
| if (req->tx_len) { |
| data->written = MXC_I2C_WriteTXFIFO(i2c, req->tx_buf, 1); |
| MXC_I2C_EnableInt(i2c, ADI_MAX32_I2C_INT_EN0_TX_THD, 0); |
| } else { |
| MXC_I2C_EnableInt(i2c, ADI_MAX32_I2C_INT_EN0_RX_THD, 0); |
| } |
| } |
| |
| ret = k_sem_take(&data->xfer, K_FOREVER); |
| if (data->err) { |
| MXC_I2C_Stop(i2c); |
| ret = data->err; |
| } else { |
| if (data->flags & I2C_MSG_STOP) { |
| /* Wait for busy flag to be cleared */ |
| while (i2c->status & ADI_MAX32_I2C_STATUS_MASTER_BUSY) { |
| } |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_MASK, |
| ADI_MAX32_I2C_INT_FL1_MASK); |
| } |
| } |
| if (ret) { |
| break; |
| } |
| } |
| |
| k_sem_give(&data->lock); |
| |
| return ret; |
| } |
| #else |
| static int i2c_max32_transfer(const struct device *dev, struct i2c_msg *msgs, uint8_t num_msgs, |
| uint16_t target_address) |
| { |
| int ret = 0; |
| const struct max32_i2c_config *const cfg = dev->config; |
| struct max32_i2c_data *data = dev->data; |
| mxc_i2c_regs_t *i2c = cfg->regs; |
| mxc_i2c_req_t *req = &data->req; |
| uint8_t target_rw; |
| unsigned int i = 0; |
| |
| req->i2c = i2c; |
| req->addr = target_address; |
| |
| k_sem_take(&data->lock, K_FOREVER); |
| |
| MXC_I2C_ClearRXFIFO(i2c); |
| |
| /* First message should always begin with a START condition */ |
| msgs[0].flags |= I2C_MSG_RESTART; |
| |
| for (i = 0; i < num_msgs; i++) { |
| if (msgs[i].flags & I2C_MSG_READ) { |
| req->rx_buf = (unsigned char *)msgs[i].buf; |
| req->rx_len = msgs[i].len; |
| req->tx_buf = NULL; |
| req->tx_len = 0; |
| target_rw = (target_address << 1) | 0x1; |
| } else { |
| req->tx_buf = (unsigned char *)msgs[i].buf; |
| req->tx_len = msgs[i].len; |
| req->rx_buf = NULL; |
| req->rx_len = 0; |
| target_rw = (target_address << 1) & ~0x1; |
| } |
| |
| /* |
| * If previous message ends with a STOP condition, this message |
| * should begin with a START |
| */ |
| if (i > 0) { |
| if ((msgs[i - 1].flags & (I2C_MSG_STOP | I2C_MSG_READ))) { |
| msgs[i].flags |= I2C_MSG_RESTART; |
| } |
| } |
| |
| data->flags = msgs[i].flags; |
| data->readb = 0; |
| data->written = 0; |
| |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_MASK, ADI_MAX32_I2C_INT_FL1_MASK); |
| |
| Wrap_MXC_I2C_SetIntEn(i2c, 0, 0); |
| if (data->flags & I2C_MSG_RESTART) { |
| MXC_I2C_Start(i2c); |
| Wrap_MXC_I2C_WaitForRestart(i2c); |
| MXC_I2C_WriteTXFIFO(i2c, &target_rw, 1); |
| } |
| ret = i2c_max32_transfer_sync(i2c, data); |
| if (ret) { |
| MXC_I2C_Stop(i2c); |
| break; |
| } |
| } |
| |
| k_sem_give(&data->lock); |
| |
| return ret; |
| } |
| #endif /* CONFIG_I2C_MAX32_INTERRUPT */ |
| |
| static int api_transfer(const struct device *dev, struct i2c_msg *msgs, uint8_t num_msgs, |
| uint16_t target_address) |
| { |
| #if CONFIG_I2C_MAX32_DMA |
| const struct max32_i2c_config *cfg = dev->config; |
| |
| if ((cfg->tx_dma.channel != 0xFF) && (cfg->rx_dma.channel != 0xFF)) { |
| return i2c_max32_transfer_dma(dev, msgs, num_msgs, target_address); |
| } |
| #endif |
| return i2c_max32_transfer(dev, msgs, num_msgs, target_address); |
| } |
| |
| #ifdef CONFIG_I2C_TARGET |
| static void i2c_max32_isr_target(const struct device *dev, mxc_i2c_regs_t *i2c) |
| { |
| uint32_t ctrl; |
| uint32_t int_fl0; |
| uint32_t int_fl1; |
| uint32_t int_en0; |
| uint32_t int_en1; |
| |
| ctrl = i2c->ctrl; |
| Wrap_MXC_I2C_GetIntEn(i2c, &int_en0, &int_en1); |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_MASK, ADI_MAX32_I2C_INT_FL1_MASK); |
| |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_ERR) { |
| /* Error occurred, notify callback function and end transaction */ |
| i2c_max32_target_callback(dev, i2c, MXC_I2C_EVT_TRANS_COMP); |
| |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_MASK, ADI_MAX32_I2C_INT_FL1_MASK); |
| MXC_I2C_ClearTXFIFO(i2c); |
| MXC_I2C_ClearRXFIFO(i2c); |
| } |
| |
| /* Check whether data is available if we received an interrupt occurred while receiving */ |
| if (int_en0 & ADI_MAX32_I2C_INT_EN0_RX_THD || int_en1 & ADI_MAX32_I2C_INT_EN1_RX_OVERFLOW) { |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_RX_THD) { |
| i2c_max32_target_callback(dev, i2c, MXC_I2C_EVT_RX_THRESH); |
| } |
| |
| if (int_fl1 & ADI_MAX32_I2C_INT_FL1_RX_OVERFLOW) { |
| i2c_max32_target_callback(dev, i2c, MXC_I2C_EVT_OVERFLOW); |
| } |
| } |
| |
| /* Check whether TX FIFO needs to be refilled if interrupt ocurred while transmitting */ |
| if (int_en0 & (ADI_MAX32_I2C_INT_EN0_TX_THD | ADI_MAX32_I2C_INT_EN0_TX_LOCK_OUT) || |
| int_en1 & ADI_MAX32_I2C_INT_EN1_TX_UNDERFLOW) { |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_TX_THD) { |
| i2c_max32_target_callback(dev, i2c, MXC_I2C_EVT_TX_THRESH); |
| } |
| |
| if (int_fl1 & ADI_MAX32_I2C_INT_EN1_TX_UNDERFLOW) { |
| i2c_max32_target_callback(dev, i2c, MXC_I2C_EVT_UNDERFLOW); |
| } |
| |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_TX_LOCK_OUT) { |
| int_en0 = ADI_MAX32_I2C_INT_EN0_ADDR_MATCH; |
| int_en1 = 0; |
| i2c_max32_target_callback(dev, i2c, MXC_I2C_EVT_TRANS_COMP); |
| } |
| } |
| |
| /* Check if transaction completed or restart occurred */ |
| if (int_en0 & ADI_MAX32_I2C_INT_EN0_DONE) { |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_STOP) { |
| /* Stop/NACK condition occurred, transaction complete */ |
| i2c_max32_target_callback(dev, i2c, MXC_I2C_EVT_TRANS_COMP); |
| int_en0 = ADI_MAX32_I2C_INT_EN0_ADDR_MATCH; |
| } else if (int_fl0 & ADI_MAX32_I2C_INT_FL0_DONE) { |
| /* Restart detected, re-arm address match interrupt */ |
| int_en0 = ADI_MAX32_I2C_INT_EN0_ADDR_MATCH; |
| } |
| int_en1 = 0; |
| } |
| |
| /* Check for address match interrupt */ |
| if (int_en0 & ADI_MAX32_I2C_INT_EN0_ADDR_MATCH) { |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_ADDR_MATCH) { |
| /* Address match occurred, prepare for transaction */ |
| if (i2c->ctrl & MXC_F_I2C_CTRL_READ) { |
| /* Read request received from the master */ |
| i2c_max32_target_callback(dev, i2c, MXC_I2C_EVT_MASTER_RD); |
| int_en0 = ADI_MAX32_I2C_INT_EN0_TX_THD | |
| ADI_MAX32_I2C_INT_EN0_TX_LOCK_OUT | |
| ADI_MAX32_I2C_INT_EN0_DONE | ADI_MAX32_I2C_INT_EN0_ERR; |
| int_en1 = ADI_MAX32_I2C_INT_EN1_TX_UNDERFLOW; |
| } else { |
| /* Write request received from the master */ |
| i2c_max32_target_callback(dev, i2c, MXC_I2C_EVT_MASTER_WR); |
| int_en0 = ADI_MAX32_I2C_INT_EN0_RX_THD | |
| ADI_MAX32_I2C_INT_EN0_DONE | ADI_MAX32_I2C_INT_EN0_ERR; |
| int_en1 = ADI_MAX32_I2C_INT_EN1_RX_OVERFLOW; |
| } |
| } |
| } |
| Wrap_MXC_I2C_SetIntEn(i2c, int_en0, int_en1); |
| } |
| #endif /* CONFIG_I2C_TARGET */ |
| |
| #ifdef CONFIG_I2C_MAX32_INTERRUPT |
| static void i2c_max32_isr_controller(const struct device *dev, mxc_i2c_regs_t *i2c) |
| { |
| struct max32_i2c_data *data = dev->data; |
| mxc_i2c_req_t *req = &data->req; |
| uint32_t written, readb; |
| uint32_t txfifolevel; |
| uint32_t int_fl0, int_fl1; |
| uint32_t int_en0, int_en1; |
| |
| written = data->written; |
| readb = data->readb; |
| |
| Wrap_MXC_I2C_GetIntEn(i2c, &int_en0, &int_en1); |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_MASK, ADI_MAX32_I2C_INT_FL1_MASK); |
| txfifolevel = Wrap_MXC_I2C_GetTxFIFOLevel(i2c); |
| |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_ERR) { |
| data->err = -EIO; |
| Wrap_MXC_I2C_SetIntEn(i2c, 0, 0); |
| k_sem_give(&data->xfer); |
| return; |
| } |
| |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_ADDR_ACK) { |
| MXC_I2C_DisableInt(i2c, ADI_MAX32_I2C_INT_EN0_ADDR_ACK, 0); |
| if (written < req->tx_len) { |
| MXC_I2C_EnableInt(i2c, ADI_MAX32_I2C_INT_EN0_TX_THD, 0); |
| } else if (readb < req->rx_len) { |
| MXC_I2C_EnableInt( |
| i2c, ADI_MAX32_I2C_INT_EN0_RX_THD | ADI_MAX32_I2C_INT_EN0_DONE, 0); |
| } |
| } |
| |
| if (req->tx_len && |
| (int_fl0 & (ADI_MAX32_I2C_INT_FL0_TX_THD | ADI_MAX32_I2C_INT_FL0_DONE))) { |
| if (written < req->tx_len) { |
| written += MXC_I2C_WriteTXFIFO(i2c, &req->tx_buf[written], |
| req->tx_len - written); |
| } else { |
| if (!(int_en0 & ADI_MAX32_I2C_INT_EN0_DONE)) { |
| /* We are done, stop sending more data */ |
| MXC_I2C_DisableInt(i2c, ADI_MAX32_I2C_INT_EN0_TX_THD, 0); |
| if (data->flags & I2C_MSG_STOP) { |
| MXC_I2C_EnableInt(i2c, ADI_MAX32_I2C_INT_EN0_DONE, 0); |
| /* Done flag is not set if stop/restart is not set */ |
| Wrap_MXC_I2C_Stop(i2c); |
| } else { |
| k_sem_give(&data->xfer); |
| } |
| } |
| |
| if ((int_fl0 & ADI_MAX32_I2C_INT_FL0_DONE)) { |
| MXC_I2C_DisableInt(i2c, ADI_MAX32_I2C_INT_EN0_DONE, 0); |
| k_sem_give(&data->xfer); |
| } |
| } |
| } else if ((int_fl0 & (ADI_MAX32_I2C_INT_FL0_RX_THD | ADI_MAX32_I2C_INT_FL0_DONE))) { |
| readb += MXC_I2C_ReadRXFIFO(i2c, &req->rx_buf[readb], req->rx_len - readb); |
| if (readb == req->rx_len) { |
| MXC_I2C_DisableInt(i2c, ADI_MAX32_I2C_INT_EN0_RX_THD, 0); |
| if (data->flags & I2C_MSG_STOP) { |
| MXC_I2C_DisableInt(i2c, ADI_MAX32_I2C_INT_EN0_DONE, 0); |
| Wrap_MXC_I2C_Stop(i2c); |
| k_sem_give(&data->xfer); |
| } else { |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_DONE) { |
| MXC_I2C_DisableInt(i2c, ADI_MAX32_I2C_INT_EN0_DONE, 0); |
| k_sem_give(&data->xfer); |
| } |
| } |
| } else if ((int_en0 & ADI_MAX32_I2C_INT_EN0_DONE) && |
| (int_fl0 & ADI_MAX32_I2C_INT_FL0_DONE)) { |
| MXC_I2C_DisableInt( |
| i2c, (ADI_MAX32_I2C_INT_EN0_RX_THD | ADI_MAX32_I2C_INT_EN0_DONE), |
| 0); |
| Wrap_MXC_I2C_SetRxCount(i2c, req->rx_len - readb); |
| MXC_I2C_EnableInt(i2c, ADI_MAX32_I2C_INT_EN0_ADDR_ACK, 0); |
| i2c->fifo = (req->addr << 1) | 0x1; |
| Wrap_MXC_I2C_Restart(i2c); |
| } |
| } |
| |
| data->written = written; |
| data->readb = readb; |
| } |
| #endif /* CONFIG_I2C_MAX32_INTERRUPT */ |
| |
| #ifdef CONFIG_I2C_MAX32_DMA |
| static void i2c_max32_isr_controller_dma(const struct device *dev, mxc_i2c_regs_t *i2c) |
| { |
| struct max32_i2c_data *data = dev->data; |
| uint32_t int_fl0, int_fl1; |
| uint32_t int_en0, int_en1; |
| |
| Wrap_MXC_I2C_GetIntEn(i2c, &int_en0, &int_en1); |
| MXC_I2C_GetFlags(i2c, &int_fl0, &int_fl1); |
| MXC_I2C_ClearFlags(i2c, ADI_MAX32_I2C_INT_FL0_MASK, ADI_MAX32_I2C_INT_FL1_MASK); |
| |
| if (int_fl0 & ADI_MAX32_I2C_INT_FL0_ERR) { |
| data->err = -EIO; |
| Wrap_MXC_I2C_SetIntEn(i2c, 0, 0); |
| k_sem_give(&data->xfer); |
| } else { |
| if (!data->err && (int_en0 & ADI_MAX32_I2C_INT_EN0_DONE)) { |
| k_sem_give(&data->xfer); |
| } |
| } |
| } |
| #endif /* CONFIG_I2C_MAX32_DMA */ |
| |
| #if defined(CONFIG_I2C_TARGET) || defined(CONFIG_I2C_MAX32_INTERRUPT) |
| static void i2c_max32_isr(const struct device *dev) |
| { |
| const struct max32_i2c_config *cfg = dev->config; |
| struct max32_i2c_data *data = dev->data; |
| mxc_i2c_regs_t *i2c = cfg->regs; |
| |
| #ifdef CONFIG_I2C_MAX32_INTERRUPT |
| if (data->target_mode == 0) { |
| #ifdef CONFIG_I2C_MAX32_DMA |
| if ((cfg->tx_dma.channel != 0xFF) && (cfg->rx_dma.channel != 0xFF)) { |
| i2c_max32_isr_controller_dma(dev, i2c); |
| return; |
| } |
| #endif |
| i2c_max32_isr_controller(dev, i2c); |
| return; |
| } |
| #endif /* CONFIG_I2C_MAX32_INTERRUPT */ |
| |
| #ifdef CONFIG_I2C_TARGET |
| if (data->target_mode == 1) { |
| i2c_max32_isr_target(dev, i2c); |
| } |
| #endif |
| } |
| #endif /* CONFIG_I2C_TARGET || CONFIG_I2C_MAX32_INTERRUPT */ |
| |
| static const struct i2c_driver_api api = { |
| .configure = api_configure, |
| .transfer = api_transfer, |
| #ifdef CONFIG_I2C_TARGET |
| .target_register = api_target_register, |
| .target_unregister = api_target_unregister, |
| #endif |
| #ifdef CONFIG_I2C_RTIO |
| .iodev_submit = i2c_iodev_submit_fallback, |
| #endif |
| .recover_bus = api_recover_bus, |
| }; |
| |
| static int i2c_max32_init(const struct device *dev) |
| { |
| const struct max32_i2c_config *const cfg = dev->config; |
| struct max32_i2c_data *data = dev->data; |
| mxc_i2c_regs_t *i2c = cfg->regs; |
| int ret = 0; |
| |
| if (!device_is_ready(cfg->clock)) { |
| return -ENODEV; |
| } |
| |
| MXC_I2C_Shutdown(i2c); /* Clear everything out */ |
| |
| ret = clock_control_on(cfg->clock, (clock_control_subsys_t)&cfg->perclk); |
| if (ret) { |
| return ret; |
| } |
| |
| ret = pinctrl_apply_state(cfg->pctrl, PINCTRL_STATE_DEFAULT); |
| if (ret) { |
| return ret; |
| } |
| |
| ret = MXC_I2C_Init(i2c, 1, 0); /* Configure as master */ |
| if (ret) { |
| return ret; |
| } |
| |
| MXC_I2C_SetFrequency(i2c, cfg->bitrate); |
| |
| k_sem_init(&data->lock, 1, 1); |
| |
| #if defined(CONFIG_I2C_TARGET) || defined(CONFIG_I2C_MAX32_INTERRUPT) |
| cfg->irq_config_func(dev); |
| #endif |
| |
| #ifdef CONFIG_I2C_MAX32_INTERRUPT |
| irq_enable(cfg->irqn); |
| |
| k_sem_init(&data->xfer, 0, 1); |
| #endif |
| |
| #if defined(CONFIG_I2C_TARGET) |
| data->first_write = true; |
| data->target_mode = 0; |
| #endif |
| data->dev = dev; |
| |
| return ret; |
| } |
| |
| #if defined(CONFIG_I2C_TARGET) || defined(CONFIG_I2C_MAX32_INTERRUPT) |
| #define I2C_MAX32_CONFIG_IRQ_FUNC(n) \ |
| .irq_config_func = i2c_max32_irq_config_func_##n, .irqn = DT_INST_IRQN(n), |
| |
| #define I2C_MAX32_IRQ_CONFIG_FUNC(n) \ |
| static void i2c_max32_irq_config_func_##n(const struct device *dev) \ |
| { \ |
| IRQ_CONNECT(DT_INST_IRQN(n), DT_INST_IRQ(n, priority), i2c_max32_isr, \ |
| DEVICE_DT_INST_GET(n), 0); \ |
| } |
| #else |
| #define I2C_MAX32_CONFIG_IRQ_FUNC(n) |
| #define I2C_MAX32_IRQ_CONFIG_FUNC(n) |
| #endif |
| |
| #if CONFIG_I2C_MAX32_DMA |
| #define MAX32_DT_INST_DMA_CTLR(n, name) \ |
| COND_CODE_1(DT_INST_NODE_HAS_PROP(n, dmas), \ |
| (DEVICE_DT_GET(DT_INST_DMAS_CTLR_BY_NAME(n, name))), (NULL)) |
| |
| #define MAX32_DT_INST_DMA_CELL(n, name, cell) \ |
| COND_CODE_1(DT_INST_NODE_HAS_PROP(n, dmas), (DT_INST_DMAS_CELL_BY_NAME(n, name, cell)), \ |
| (0xff)) |
| |
| #define MAX32_I2C_TX_DMA_INIT(n) \ |
| .tx_dma.dev = MAX32_DT_INST_DMA_CTLR(n, tx), \ |
| .tx_dma.channel = MAX32_DT_INST_DMA_CELL(n, tx, channel), \ |
| .tx_dma.slot = MAX32_DT_INST_DMA_CELL(n, tx, slot), |
| #define MAX32_I2C_RX_DMA_INIT(n) \ |
| .rx_dma.dev = MAX32_DT_INST_DMA_CTLR(n, rx), \ |
| .rx_dma.channel = MAX32_DT_INST_DMA_CELL(n, rx, channel), \ |
| .rx_dma.slot = MAX32_DT_INST_DMA_CELL(n, rx, slot), |
| #else |
| #define MAX32_I2C_TX_DMA_INIT(n) |
| #define MAX32_I2C_RX_DMA_INIT(n) |
| #endif |
| |
| #define DEFINE_I2C_MAX32(_num) \ |
| PINCTRL_DT_INST_DEFINE(_num); \ |
| I2C_MAX32_IRQ_CONFIG_FUNC(_num) \ |
| static const struct max32_i2c_config max32_i2c_dev_cfg_##_num = { \ |
| .regs = (mxc_i2c_regs_t *)DT_INST_REG_ADDR(_num), \ |
| .pctrl = PINCTRL_DT_INST_DEV_CONFIG_GET(_num), \ |
| .clock = DEVICE_DT_GET(DT_INST_CLOCKS_CTLR(_num)), \ |
| .perclk.bus = DT_INST_CLOCKS_CELL(_num, offset), \ |
| .perclk.bit = DT_INST_CLOCKS_CELL(_num, bit), \ |
| .bitrate = DT_INST_PROP(_num, clock_frequency), \ |
| I2C_MAX32_CONFIG_IRQ_FUNC(_num) MAX32_I2C_TX_DMA_INIT(_num) \ |
| MAX32_I2C_RX_DMA_INIT(_num)}; \ |
| static struct max32_i2c_data max32_i2c_data_##_num; \ |
| I2C_DEVICE_DT_INST_DEFINE(_num, i2c_max32_init, NULL, &max32_i2c_data_##_num, \ |
| &max32_i2c_dev_cfg_##_num, PRE_KERNEL_2, \ |
| CONFIG_I2C_INIT_PRIORITY, &api); |
| |
| DT_INST_FOREACH_STATUS_OKAY(DEFINE_I2C_MAX32) |