| # Raytac MDBT53-DB-40 nRF5340 board configuration |
| |
| # Copyright (c) 2019-2020 Nordic Semiconductor ASA |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| if BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUAPP || BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUAPP_NS |
| |
| # Code Partition: |
| # |
| # For the secure version of the board the firmware is linked at the beginning |
| # of the flash, or into the code-partition defined in DT if it is intended to |
| # be loaded by MCUboot. If the secure firmware is to be combined with a non- |
| # secure image (TRUSTED_EXECUTION_SECURE=y), the secure FW image shall always |
| # be restricted to the size of its code partition. |
| # |
| # For the non-secure version of the board, the firmware |
| # must be linked into the code-partition (non-secure) defined in DT, regardless. |
| # Apply this configuration below by setting the Kconfig symbols used by |
| # the linker according to the information extracted from DT partitions. |
| |
| # SRAM Partition: |
| # |
| # If the secure firmware is to be combined with a non-secure image |
| # (TRUSTED_EXECUTION_SECURE=y), the secure FW image SRAM shall always |
| # be restricted to the secure image SRAM partition (sram-secure-partition). |
| # Otherwise (if TRUSTED_EXECUTION_SECURE is not set) the whole zephyr,sram |
| # may be used by the image. |
| # |
| # For the non-secure version of the board, the firmware image SRAM is |
| # always restricted to the allocated non-secure SRAM partition. |
| # |
| # Workaround for not being able to have commas in macro arguments |
| DT_CHOSEN_Z_CODE_PARTITION := zephyr,code-partition |
| DT_CHOSEN_Z_SRAM_PARTITION := zephyr,sram-secure-partition |
| |
| if BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUAPP && TRUSTED_EXECUTION_SECURE |
| |
| config FLASH_LOAD_SIZE |
| default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION)) |
| |
| config SRAM_SIZE |
| default $(dt_chosen_reg_size_int,$(DT_CHOSEN_Z_SRAM_PARTITION),0,K) |
| |
| endif # BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUAPP && TRUSTED_EXECUTION_SECURE |
| |
| if BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUAPP_NS |
| |
| config FLASH_LOAD_OFFSET |
| default $(dt_chosen_reg_addr_hex,$(DT_CHOSEN_Z_CODE_PARTITION)) |
| |
| config FLASH_LOAD_SIZE |
| default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION)) |
| |
| endif # BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUAPP_NS |
| |
| choice BT_HCI_BUS_TYPE |
| default BT_HCI_IPC if BT |
| endchoice |
| |
| config HEAP_MEM_POOL_ADD_SIZE_BOARD |
| int |
| default 4096 if BT_HCI_IPC |
| |
| endif # BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUAPP || BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUAPP_NS |
| |
| config IPM_NRFX |
| default IPM |
| |
| config MBOX_NRFX_IPC |
| default MBOX |
| |
| if BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUNET |
| |
| config BT_CTLR |
| default y if BT |
| |
| endif # BOARD_RAYTAC_MDBT53_DB_40_NRF5340_CPUNET |