| .. _arduino_nicla_sense_me: |
| |
| Arduino Nicla Sense ME |
| ###################### |
| |
| Overview |
| ******** |
| The `Arduino Nicla Sense ME`_ is designed around Nordic Semiconductor's |
| nrf52832 ARM Cortex-M4F CPU. The board houses 4 low power industrial grade sensors |
| that can measure rotation, acceleration, pressure, humidity, temperature, air quality |
| and CO2 levels. |
| |
| .. figure:: arduino_nicla_sense_me.jpg |
| :align: center |
| :alt: Arduino Nicla Sense ME |
| |
| Arduino Nicla Sense ME (Credit: Arduino) |
| |
| Hardware |
| ******** |
| |
| - nRF52832 ARM Cortex-M4 processor at 64 MHz |
| - 512 kB flash memory, 64 kB SRAM |
| - Bluetooth Low Energy |
| - Micro USB (USB-B) |
| - JST 3-pin 1.2 mm pitch battery connector |
| - 10 Digital I/O pins |
| - 2 Analog input pins |
| - 12 PWM pins |
| - One reset button |
| - RGB LED (I2C) |
| - On board sensors: |
| |
| - Accelerometer/Gyroscope: Bosch BHI260AP |
| - Gas/Pressure/Temperature/Humidity: Bosch BME688 |
| - Geomagnetic: Bosch BMM150 |
| - Digital Pressure: Bosch BMP390 |
| |
| Supported Features |
| ================== |
| |
| +-----------+------------+----------------------+ |
| | Interface | Controller | Driver/Component | |
| +===========+============+======================+ |
| | ADC | on-chip | adc | |
| +-----------+------------+----------------------+ |
| | CLOCK | on-chip | clock_control | |
| +-----------+------------+----------------------+ |
| | FLASH | on-chip | flash | |
| +-----------+------------+----------------------+ |
| | GPIO | on-chip | gpio | |
| +-----------+------------+----------------------+ |
| | I2C(M/S) | on-chip | i2c | |
| +-----------+------------+----------------------+ |
| | MPU | on-chip | arch/arm | |
| +-----------+------------+----------------------+ |
| | NVIC | on-chip | arch/arm | |
| +-----------+------------+----------------------+ |
| | PWM | on-chip | pwm | |
| +-----------+------------+----------------------+ |
| | RADIO | on-chip | Bluetooth Low Energy | |
| +-----------+------------+----------------------+ |
| | RTC | on-chip | system clock | |
| +-----------+------------+----------------------+ |
| | SPI(M/S) | on-chip | spi | |
| +-----------+------------+----------------------+ |
| | UART | on-chip | serial | |
| +-----------+------------+----------------------+ |
| | WDT | on-chip | watchdog | |
| +-----------+------------+----------------------+ |
| |
| Connections and IOs |
| =================== |
| |
| Available pins: |
| --------------- |
| .. figure:: arduino_nicla_sense_me_pinout.jpg |
| :align: center |
| :alt: Arduino Nicla Sense ME pinout |
| |
| Arduino Nicla Sense ME pinout (Credit: Arduino) |
| |
| For more details please refer to the `datasheet`_, `full pinout`_ and the `schematics`_. |
| |
| Programming and Debugging |
| ************************* |
| |
| Applications for the ``arduino_nicla_sense_me`` board configuration can be built and |
| flashed in the usual way (see :ref:`build_an_application` and |
| :ref:`application_run` for more details). |
| |
| Flashing |
| ======== |
| |
| First, connect the Arduino Nicla Sense ME board to your host computer using |
| the USB port to prepare it for flashing. Then build and flash your application. |
| |
| Here is an example for the :ref:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: arduino_nicla_sense_me |
| :goals: build flash |
| |
| Run a serial host program to connect with your board: |
| |
| .. code-block:: console |
| |
| $ minicom -D /dev/ttyACM0 |
| |
| You should see the following message on the console: |
| |
| .. code-block:: console |
| |
| Hello World! arduino_nicla_sense_me |
| |
| Debugging |
| ========= |
| |
| You can debug an application in the usual way. Here is an example for the |
| :ref:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: arduino_nicla_sense_me |
| :goals: debug |
| |
| References |
| ********** |
| |
| .. target-notes:: |
| |
| .. _Arduino Nicla Sense ME: |
| https://docs.arduino.cc/hardware/nicla-sense-me |
| |
| .. _datasheet: |
| https://docs.arduino.cc/resources/datasheets/ABX00050-datasheet.pdf |
| |
| .. _full pinout: |
| https://docs.arduino.cc/resources/pinouts/ABX00050-full-pinout.pdf |
| |
| .. _schematics: |
| https://docs.arduino.cc/resources/schematics/ABX00050-schematics.pdf |