blob: 06d6a4d0c274cf0ed1911bd5aa3d624cbda01259 [file] [log] [blame]
/*
* Copyright (c) 2020 STMicroelectronics
*
* SPDX-License-Identifier: Apache-2.0
*/
/dts-v1/;
#include <st/wl/stm32wl55Xc.dtsi>
#include <st/wl/stm32wl55jcix-pinctrl.dtsi>
#include "arduino_r3_connector.dtsi"
/ {
model = "STMicroelectronics STM32WL55JC-NUCLEO board";
compatible = "st,stm32wl55-nucleo";
chosen {
zephyr,console = &lpuart1;
zephyr,shell-uart = &lpuart1;
zephyr,sram = &sram0;
zephyr,flash = &flash0;
zephyr,code-partition = &flash0;
};
leds {
compatible = "gpio-leds";
blue_led_1: led_0 {
gpios = <&gpiob 15 GPIO_ACTIVE_HIGH>;
label = "User LED1";
};
green_led_2: led_1 {
gpios = <&gpiob 9 GPIO_ACTIVE_HIGH>;
label = "User LED2";
};
green_led_3: led_2 {
gpios = <&gpiob 11 GPIO_ACTIVE_HIGH>;
label = "User LED3";
};
};
gpio_keys {
compatible = "gpio-keys";
user_button_1: button_0 {
label = "SW1";
gpios = <&gpioa 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
};
user_button_2: button_1 {
label = "SW2";
gpios = <&gpioa 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
};
user_button_3: button_2 {
label = "SW3";
gpios = <&gpioc 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
};
};
aliases {
led0 = &green_led_2;
sw0 = &user_button_1;
sw1 = &user_button_2;
sw2 = &user_button_3;
lora0 = &lora;
watchdog0 = &iwdg;
};
power-states {
stop0: state0 {
compatible = "zephyr,power-state";
power-state-name = "suspend-to-idle";
substate-id = <1>;
min-residency-us = <100>;
};
stop1: state1 {
compatible = "zephyr,power-state";
power-state-name = "suspend-to-idle";
substate-id = <2>;
min-residency-us = <500>;
};
stop2: state2 {
compatible = "zephyr,power-state";
power-state-name = "suspend-to-idle";
substate-id = <3>;
min-residency-us = <900>;
};
};
};
&cpu0 {
cpu-power-states = <&stop0 &stop1 &stop2>;
};
&clk_lsi {
status = "okay";
};
&lptim1 {
clocks = <&rcc STM32_CLOCK_BUS_APB1 0x80000000>,
<&rcc STM32_SRC_LSI LPTIM1_SEL(1)>;
status = "okay";
};
&clk_hsi {
status = "okay";
};
&pll {
div-m = <1>;
mul-n = <6>;
div-r = <2>;
div-q = <2>;
clocks = <&clk_hsi>;
status = "okay";
};
&rcc {
clocks = <&pll>;
clock-frequency = <DT_FREQ_M(48)>;
cpu1-prescaler = <1>;
cpu2-prescaler = <1>;
ahb3-prescaler = <1>;
apb1-prescaler = <1>;
apb2-prescaler = <1>;
};
&lpuart1 {
pinctrl-0 = <&lpuart1_tx_pa2 &lpuart1_rx_pa3>;
pinctrl-names = "default";
current-speed = <115200>;
status = "okay";
};
&i2c2 {
pinctrl-0 = <&i2c2_scl_pa12 &i2c2_sda_pa11>;
pinctrl-names = "default";
status = "okay";
clock-frequency = <I2C_BITRATE_FAST>;
};
&spi1 {
pinctrl-0 = <&spi1_nss_pa4 &spi1_sck_pa5
&spi1_miso_pa6 &spi1_mosi_pa7>;
pinctrl-names = "default";
status = "okay";
};
&dac1 {
pinctrl-0 = <&dac_out1_pa10>;
pinctrl-names = "default";
status = "okay";
};
&timers2 {
status = "okay";
pwm2: pwm {
status = "okay";
pinctrl-0 = <&tim2_ch4_pb11>;
pinctrl-names = "default";
};
};
&adc1 {
pinctrl-0 = <&adc_in5_pb1>;
pinctrl-names = "default";
status = "okay";
};
&die_temp {
status = "okay";
};
&aes {
status = "okay";
};
&rng {
status = "okay";
};
&iwdg {
status = "okay";
};
&subghzspi {
status = "okay";
lora: radio@0 {
status = "okay";
tx-enable-gpios = <&gpioc 4 GPIO_ACTIVE_LOW>;
rx-enable-gpios = <&gpioc 5 GPIO_ACTIVE_LOW>;
dio3-tcxo-voltage = <SX126X_DIO3_TCXO_1V7>;
tcxo-power-startup-delay-ms = <5>;
};
};
&flash0 {
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
/*
* Set 16kB of storage (8x2kB pages) at the end of the 256kB of
* flash.
*/
storage_partition: partition@3c000 {
label = "storage";
reg = <0x0003c000 DT_SIZE_K(16)>;
};
};
};