| /* SPDX-License-Identifier: Apache-2.0 */ |
| |
| /dts-v1/; |
| |
| #include <nxp/nxp_k6x.dtsi> |
| |
| / { |
| model = "NXP Freedom MK64F board"; |
| compatible = "nxp,mk64f12", "nxp,k64f", "nxp,k6x"; |
| |
| aliases { |
| adc-0 = &adc0; |
| adc-1 = &adc1; |
| pwm-0 = &pwm0; |
| pwm-1 = &pwm1; |
| pwm-2 = &pwm2; |
| pwm-3 = &pwm3; |
| uart-0 = &uart0; |
| uart-3 = &uart3; |
| pinmux-a = &pinmux_a; |
| pinmux-b = &pinmux_b; |
| pinmux-c = &pinmux_c; |
| pinmux-d = &pinmux_d; |
| pinmux-e = &pinmux_e; |
| gpio-a = &gpioa; |
| gpio-b = &gpiob; |
| gpio-c = &gpioc; |
| gpio-d = &gpiod; |
| gpio-e = &gpioe; |
| i2c-0 = &i2c0; |
| i2c-1 = &i2c1; |
| i2c-2 = &i2c2; |
| led0 = &green_led; |
| led1 = &blue_led; |
| led2 = &red_led; |
| sw0 = &user_button_3; |
| sw1 = &user_button_2; |
| eth = ð |
| can-0 = &can0; |
| }; |
| |
| chosen { |
| zephyr,sram = &sram0; |
| zephyr,flash = &flash0; |
| zephyr,code-partition = &slot0_partition; |
| zephyr,console = &uart0; |
| zephyr,shell-uart = &uart0; |
| zephyr,uart-pipe = &uart0; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| red_led: led_0 { |
| gpios = <&gpiob 22 0>; |
| label = "User LD1"; |
| }; |
| green_led: led_1 { |
| gpios = <&gpioe 26 0>; |
| label = "User LD2"; |
| }; |
| blue_led: led_2 { |
| gpios = <&gpiob 21 0>; |
| label = "User LD3"; |
| }; |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| user_button_2: button_0 { |
| label = "User SW2"; |
| gpios = <&gpioc 6 GPIO_INT_ACTIVE_LOW>; |
| }; |
| user_button_3: button_1 { |
| label = "User SW3"; |
| gpios = <&gpioa 4 (GPIO_INT_ACTIVE_LOW | GPIO_PUD_PULL_UP)>; |
| }; |
| }; |
| |
| arduino_header: connector { |
| compatible = "arduino-header-r3"; |
| #gpio-cells = <2>; |
| gpio-map-mask = <0xffffffff 0xffffffc0>; |
| gpio-map-pass-thru = <0 0x3f>; |
| gpio-map = <0 0 &gpiob 2 0>, /* A0 */ |
| <1 0 &gpiob 3 0>, /* A1 */ |
| <2 0 &gpiob 10 0>, /* A2 */ |
| <3 0 &gpiob 11 0>, /* A3 */ |
| <4 0 &gpioc 11 0>, /* A4 */ |
| <5 0 &gpioc 10 0>, /* A5 */ |
| <6 0 &gpioc 16 0>, /* D0 */ |
| <7 0 &gpioc 17 0>, /* D1 */ |
| <8 0 &gpiob 9 0>, /* D2 */ |
| <9 0 &gpioa 1 0>, /* D3 */ |
| <10 0 &gpiob 23 0>, /* D4 */ |
| <11 0 &gpioa 2 0>, /* D5 */ |
| <12 0 &gpioc 2 0>, /* D6 */ |
| <13 0 &gpioc 3 0>, /* D7 */ |
| /* NOTE: HW Rev D and below use: */ |
| /* <14 0 &gpioa 0 0>, */ |
| /* NOTE: HW Rev E and on use: */ |
| <14 0 &gpioc 12 0>, /* D8 */ |
| <15 0 &gpioc 4 0>, /* D9 */ |
| <16 0 &gpiod 0 0>, /* D10 */ |
| <17 0 &gpiod 2 0>, /* D11 */ |
| <18 0 &gpiod 3 0>, /* D12 */ |
| <19 0 &gpiod 1 0>, /* D13 */ |
| <20 0 &gpioe 25 0>, /* D14 */ |
| <21 0 &gpioe 24 0>; /* D15 */ |
| }; |
| }; |
| |
| arduino_serial: &uart3 { |
| status = "okay"; |
| current-speed = <115200>; |
| }; |
| |
| &cpu0 { |
| clock-frequency = <120000000>; |
| }; |
| |
| &adc0 { |
| status = "okay"; |
| }; |
| |
| &adc1 { |
| status = "okay"; |
| }; |
| |
| arduino_i2c: &i2c0 { |
| status = "okay"; |
| |
| fxos8700@1d { |
| compatible = "nxp,fxos8700"; |
| reg = <0x1d>; |
| label = "FXOS8700"; |
| int1-gpios = <&gpioc 6 0>; |
| int2-gpios = <&gpioc 13 0>; |
| }; |
| }; |
| |
| arduino_spi: &spi0 { |
| status = "okay"; |
| }; |
| |
| &pwm3 { |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| current-speed = <115200>; |
| }; |
| |
| &usbd { |
| compatible = "nxp,kinetis-usbd"; |
| status = "okay"; |
| num-bidir-endpoints = <8>; |
| }; |
| |
| &flash0 { |
| /* |
| * For more information, see: |
| * http://docs.zephyrproject.org/latest/guides/dts/index.html#flash-partitions |
| */ |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x00000000 0x00010000>; |
| read-only; |
| }; |
| |
| /* |
| * The flash starting at 0x00010000 and ending at |
| * 0x0001ffff (sectors 16-31) is reserved for use |
| * by the application. |
| */ |
| storage_partition: partition@1e000 { |
| label = "storage"; |
| reg = <0x0001e000 0x00002000>; |
| }; |
| |
| slot0_partition: partition@20000 { |
| label = "image-0"; |
| reg = <0x00020000 0x00060000>; |
| }; |
| slot1_partition: partition@80000 { |
| label = "image-1"; |
| reg = <0x00080000 0x00060000>; |
| }; |
| scratch_partition: partition@e0000 { |
| label = "image-scratch"; |
| reg = <0x000e0000 0x00020000>; |
| }; |
| }; |
| }; |
| |
| ð { |
| status = "okay"; |
| ptp { |
| status = "okay"; |
| }; |
| }; |
| |
| |
| &can0 { |
| status = "okay"; |
| bus-speed = <125000>; |
| }; |