| # Kconfig - USB device configuration options |
| |
| # |
| # Copyright (c) 2016 Wind River Systems, Inc. |
| # |
| # SPDX-License-Identifier: Apache-2.0 |
| # |
| |
| if USB |
| |
| config USB_DEVICE_DRIVER |
| bool |
| |
| config USB_DW |
| bool "Designware USB Device Controller Driver" |
| select USB_DEVICE_DRIVER |
| help |
| Designware USB Device Controller Driver. |
| |
| config USB_DW_IRQ_PRI |
| int "DesignWare USB Driver Interrupt priority" |
| depends on USB_DW |
| help |
| USB interrupt priority. |
| |
| config USB_DW_USB_2_0 |
| bool "DesignWare Controller and PHY support for USB specification 2.0" |
| depends on USB_DW |
| help |
| Indicates whether or not USB specification version 2.0 is supported |
| |
| config USB_DC_STM32 |
| bool "USB device controller driver for STM32 devices" |
| depends on SOC_FAMILY_STM32 |
| select USB_DEVICE_DRIVER |
| select USE_STM32_LL_USB if !SOC_SERIES_STM32F0X && !SOC_SERIES_STM32F3X && !SOC_SERIES_STM32L0X |
| select USE_STM32_HAL_PCD |
| select USE_STM32_HAL_PCD_EX |
| select HAS_DTS_USB |
| help |
| Enable USB support on the STM32 F0, F1, F2, F3, F4, F7, L0 and L4 family of |
| processors. |
| |
| config USB_DC_SAM0 |
| bool "SAM0 series USB Device Controller driver" |
| default y |
| depends on SOC_FAMILY_SAM0 |
| select USB_DEVICE_DRIVER |
| help |
| SAM0 family USB device controller Driver. |
| |
| config USB_DC_SAM |
| bool "SAM series USB HS Device Controller driver" |
| depends on SOC_SERIES_SAME70 |
| select USB_DEVICE_DRIVER |
| select HAS_DTS_USB |
| help |
| SAM family USB HS device controller Driver. |
| |
| menuconfig USB_NRF52840 |
| bool "Nordic Semiconductor nRF52840 USB Device Controller Driver" |
| default y |
| depends on SOC_NRF52840 |
| select USB_DEVICE_DRIVER |
| select HAS_DTS_USB |
| select NRFX_USBD |
| select USB_DEVICE_REMOTE_WAKEUP |
| help |
| nRF52840 USB Device Controller Driver |
| |
| config USB_NRFX_EVT_QUEUE_SIZE |
| int "USBD event queue size" |
| default 32 |
| depends on USB_NRF52840 |
| help |
| Size of the driver's internal event queue. |
| Required size will depend on number of endpoints (class instances) in use. |
| |
| config USB_KINETIS |
| bool "Kinetis USB Device Controller Driver" |
| select USB_DEVICE_DRIVER |
| help |
| Kinetis USB Device Controller Driver. |
| |
| module = USB_DRIVER |
| module-str = usb driver |
| source "subsys/logging/Kconfig.template.log_config" |
| |
| config USB_DC_STM32_DISCONN_ENABLE |
| bool |
| depends on USB_DC_STM32 |
| help |
| Say Y if your board uses USB DISCONNECT pin to enable the |
| pull-up resistor on USB DP. |
| |
| config USB_NATIVE_POSIX |
| bool "Native Posix USB Device Controller Driver" |
| select USB_DEVICE_DRIVER |
| help |
| Native Posix USB Device Controller Driver. |
| |
| endif # USB |
