drivers/espi/Kconfig.npcx

# NPCX eSPI driver configuration options

# Copyright (c) 2020 Nuvoton Technology Corporation.
# SPDX-License-Identifier: Apache-2.0

config ESPI_NPCX
	bool "Nuvoton NPCX embedded controller (EC) ESPI driver"
	default y
	depends on SOC_FAMILY_NPCX
	depends on DT_HAS_NUVOTON_NPCX_ESPI_ENABLED
	select PINCTRL
	help
	  This option enables the Intel Enhanced Serial Peripheral Interface
	  (eSPI) for NPCX family of processors.

config ESPI_NPCX_NPCXN_V1
	bool "Nuvoton NPCX ESPI version 1 support"
	default y
	depends on $(dt_compat_any_has_prop,$(DT_COMPAT_NUVOTON_NPCX_ESPI),support-npcxn-v1,True)
	help
	  This option enables ESPI version 1 support for npcxn variant.

config ESPI_NPCX_NPCXN_V2
	bool "Nuvoton NPCX ESPI version 2 support"
	default y
	depends on $(dt_compat_any_has_prop,$(DT_COMPAT_NUVOTON_NPCX_ESPI),support-npcxn-v2,True)
	help
	  This option enables ESPI version 2 support for npcxn variant.

config ESPI_NPCX_NPCXN_V3
	bool "Nuvoton NPCX ESPI version 3 support"
	default y
	depends on $(dt_compat_any_has_prop,$(DT_COMPAT_NUVOTON_NPCX_ESPI),support-npcxn-v3,True)
	help
	  This option enables ESPI version 3 support for npcxn variant.

config ESPI_NPCX_NPCKN_V1
	bool "Nuvoton NPCX ESPI version 1 support"
	default y
	depends on $(dt_compat_any_has_prop,$(DT_COMPAT_NUVOTON_NPCX_ESPI),support-npckn-v1,True)
	help
	  This option enables ESPI version 1 support for npckn variant.

config ESPI_NPCX_PERIPHERAL_ACPI_SHD_MEM_SIZE
	int "Host I/O peripheral port size for shared memory in npcx series"
	depends on ESPI_NPCX || ESPI_PERIPHERAL_ACPI_SHM_REGION
	default 256
	help
	  This is the port size used by the Host and EC to communicate over
	  the shared memory region to return the ACPI response data. Please
	  notice the valid value in npcx ec series for this option is 8/16/32/
	  64/128/256/512/1024/2048/4096 bytes.

config ESPI_NPCX_PERIPHERAL_HOST_CMD_PARAM_SIZE
	int "Host I/O peripheral port size for ec host command in npcx series"
	depends on ESPI_NPCX || ESPI_PERIPHERAL_EC_HOST_CMD
	default 256
	help
	  This is the port size used by the Host and EC to communicate over
	  the shared memory region to return the host command parameter data.
	  Please notice the valid value in npcx ec series for this option is
	  8/16/32/64/128/256/512/1024/2048/4096 bytes.

config ESPI_NPCX_BYPASS_CH_ENABLE_FATAL_ERROR
	bool
	depends on ESPI_NPCX_NPCXN_V1 || ESPI_NPCX_NPCXN_V2
	default y
	help
	  Workaround the issue documented in NPCX99nF errata rev1_2, No.3.10.
	  Enabling an eSPI channel during an eSPI transaction might
	  (with low probability) cause the eSPI_SIF module to transition to
	  a wrong state and therefore response with FATAL_ERROR on an incoming
	  transaction.

config ESPI_NPCX_PERIPHERAL_DEBUG_PORT_80_MULTI_BYTE
	bool "Host can write 1/2/4 bytes of Port80 data in a eSPI transaction"
	depends on (ESPI_NPCX_NPCXN_V2 || ESPI_NPCX_NPCXN_V3) && ESPI_PERIPHERAL_DEBUG_PORT_80
	select RING_BUFFER
	help
	  EC can accept 1/2/4 bytes of Port 80 data written from the Host in an
	  eSPI transaction.

config ESPI_NPCX_PERIPHERAL_DEBUG_PORT_80_RING_BUF_SIZE
	int "Debug Port80 ring buffer size"
	depends on ESPI_NPCX_PERIPHERAL_DEBUG_PORT_80_MULTI_BYTE
	default 256
	help
	  The size of the ring buffer in byte used by the Port80 ISR to store
	  Postcodes from Host.

config ESPI_NPCX_VWIRE_ENABLE_SEND_CHECK
	bool "Check the value was read by host after wire bits changed"
	help
	  This option enables the function to check whether the host has read the value
	  after the wire data changes.

config ESPI_NPCX_WIRE_SEND_TIMEOUT_US
	int "eSPI virtual wire send timeout count"
	default 1000
	help
	  The times to check status after sending the eSPI virtual wire signal. The unit
	  is microseconds (µs).

config ESPI_TAF_NPCX
	bool "Nuvoton NPCX embedded controller (EC) ESPI TAF driver"
	depends on ESPI_NPCX_NPCXN_V3 || ESPI_NPCX_NPCKN_V1
	depends on FLASH
	help
	  This option enables the Intel Enhanced Serial Peripheral Interface
	  Target Attached Flash (eSPI TAF) for NPCX4/NPCK3 family of processors.

choice ESPI_TAF_ACCESS_MODE_CHOICE
	prompt "eSPI TAF Read Access Mode"
	default ESPI_TAF_AUTO_MODE

config ESPI_TAF_AUTO_MODE
	bool "eSPI TAF Automatic Mode"
	help
	  This is the setting to use auto mode for eSPI TAF read.

config ESPI_TAF_MANUAL_MODE
	bool "eSPI TAF Manual Mode"
	help
	  This is the setting to use manual mode for eSPI TAF read.

endchoice

config ESPI_TAF_TX_AVAIL_CHECK_TIME
	int "Flash TX Available Check Time (microseconds)"
	default 1000000
	depends on ESPI_TAF_NPCX
	help
	  This option sets the time interval (in microseconds) for checking
	  whether the host has sent a GET_FLASH_C command to retrieve the
	  result.

config ESPI_TAF_PR_NUM
	int "Sets of protection region settings"
	default 16
	help
	  This size is display how many group of slave attached flash protection
	  region.

config ESPI_TAF_NPCX_RPMC_SUPPORT
	bool "eSPI TAF RPMC support"
	depends on ESPI_TAF_NPCX
	select FLASH_EX_OP_ENABLED
	help
	  This option enable the handler for eSPI TAF RPMC request.

config ESPI_TAF_NPCX_STS_AWAIT_TIMEOUT
	int "A timeout value in microseconds to wait for automatic read status"
	depends on ESPI_TAF_NPCX
	default 20000
	help
	  This option specifies the timeout value in microseconds (us) for checking
	  automatic read status.

# The default value 'y' for the existing options if ESPI_NPCX is selected.
if ESPI_NPCX

config ESPI_OOB_CHANNEL
	default  y

config ESPI_PERIPHERAL_8042_KBC
	default y

config ESPI_PERIPHERAL_HOST_IO
	default y

config ESPI_PERIPHERAL_DEBUG_PORT_80
	default y

config ESPI_PERIPHERAL_EC_HOST_CMD
	default y

config ESPI_PERIPHERAL_ACPI_SHM_REGION
	default y

config ESPI_PERIPHERAL_CUSTOM_OPCODE
	default y

config ESPI_NPCX_SUPP_VW_GPIO
	bool "Indicates that the eSPI hardware supports virtual wire GPIOs"
	default y if ESPI_NPCX_NPCXN_V2 || ESPI_NPCX_NPCXN_V3
	help
	  Selected if NPCX series supports virtual wire GPIOs in eSPI module.

config ESPI_NPCX_CAF_GLOBAL_RESET_WORKAROUND
	bool
	default y if ESPI_NPCX_NPCXN_V3 && ESPI_FLASH_CHANNEL
	help
	  Workaround the issue "Global Reset" in the npcx4 SoC errata.

config ESPI_NPCX_RESET_SLP_SX_VW_ON_ESPI_RST
	bool "Reset SLP_Sx virtual wires when eSPI_RST is asserted"
	help
	    The SLP_S3/SLP_S4/SLP_S5/ virtual wires are automatically reset when
	    eSPI_Reset is asserted on the global reset.
	    Don't enable this config if the platform implements the Deep-Sx
	    entry as EC needs to maintain these pins' states per request.

endif #ESPI_NPCX