| # Kconfig - SPI driver configuration options |
| |
| # |
| # Copyright (c) 2015-2016 Intel Corporation |
| # |
| # SPDX-License-Identifier: Apache-2.0 |
| # |
| |
| config SPI_LEGACY_API |
| bool "Use legacy SPI API (default)" |
| default y |
| help |
| Driver and user API is the legacy SPI API (spi_legacy.h). |
| If unselected, the new API will be used. |
| |
| # |
| # SPI Drivers |
| # |
| menuconfig SPI |
| bool |
| prompt "SPI hardware bus support" |
| default n |
| help |
| Enable support for the SPI hardware bus. |
| |
| config SPI_QMSI |
| bool "QMSI driver for SPI controller" |
| depends on SPI && QMSI |
| default n |
| help |
| SPI driver implementation using QMSI library. QMSI is the |
| Quark Microcontroller Software Interface, providing a common |
| interface to the Quark family of microcontrollers. |
| |
| config SPI_QMSI_SS |
| bool "QMSI driver for SPI controller on Sensor Subsystem" |
| depends on SPI && QMSI |
| default n |
| help |
| SPI driver implementation using QMSI library. This instance is |
| for the Sensor Subsystem. |
| |
| config SPI_INTEL |
| bool |
| prompt "Intel SPI controller driver" |
| depends on SPI && CPU_MINUTEIA |
| default n |
| help |
| Enable support for Intel's SPI controllers. Such controller |
| was formerly found on XScale chips. It can be found nowadays |
| on CEXXXX Intel media controller and Quark CPU (2 of them). |
| |
| config SPI_STM32 |
| bool |
| prompt "STM32 MCU SPI controller driver" |
| depends on SPI && SOC_FAMILY_STM32 |
| depends on SOC_SERIES_STM32L4X || SOC_SERIES_STM32F4X || SOC_SERIES_STM32F3X |
| default n |
| help |
| Enable SPI support on the STM32 family of processors. |
| |
| config SPI_STM32_INTERRUPT |
| bool |
| prompt "STM32 MCU SPI Interrupt Support" |
| depends on SPI_STM32 |
| default n |
| help |
| Enable Interrupt support for the SPI Driver of STM32 family. |
| |
| if SPI |
| config SPI_INIT_PRIORITY |
| int "Init priority" |
| default 70 |
| help |
| Device driver initialization priority. |
| |
| config SYS_LOG_SPI_LEVEL |
| int |
| prompt "SPI Driver Log level" |
| depends on SYS_LOG && SPI |
| default 0 |
| range 0 4 |
| help |
| Sets log level for SPI drivers. |
| Levels are: |
| 0 OFF, do not write |
| 1 ERROR, only write SYS_LOG_ERR |
| 2 WARNING, write SYS_LOG_WRN in addition to previous level |
| 3 INFO, write SYS_LOG_INF in addition to previous levels |
| 4 DEBUG, write SYS_LOG_DBG in addition to previous levels |
| |
| config SPI_CS_GPIO |
| bool "SPI port CS pin is controlled via a GPIO port" |
| depends on GPIO |
| default n |
| |
| config SPI_0 |
| bool |
| prompt "SPI port 0" |
| default n |
| help |
| Enable SPI controller port 0. |
| |
| config SPI_0_NAME |
| string |
| prompt "SPI port 0 device name" |
| depends on SPI_0 |
| default "SPI_0" |
| |
| config SPI_0_IRQ_PRI |
| int |
| prompt "Port 0 interrupt priority" |
| depends on SPI_0 |
| |
| config SPI_0_DEFAULT_CFG |
| hex "Port 0 default configuration" |
| depends on SPI_0 |
| default 0x80 |
| |
| config SPI_0_DEFAULT_BAUD_RATE |
| int "Port 0 default baud rate" |
| depends on SPI_0 |
| default 500000 |
| |
| config SPI_0_CS_GPIO_PORT |
| string |
| prompt "The GPIO port which is used to control CS" |
| depends on SPI_0 && SPI_CS_GPIO |
| default "GPIO_0" |
| |
| config SPI_0_CS_GPIO_PIN |
| int "The GPIO PIN which is used to act as a CS pin" |
| depends on SPI_0 && SPI_CS_GPIO |
| default 0 |
| |
| config SPI_1 |
| bool |
| prompt "SPI port 1" |
| default n |
| help |
| Enable SPI controller port 1. |
| |
| config SPI_1_NAME |
| string |
| prompt "SPI port 1 device name" |
| depends on SPI_1 |
| default "SPI_1" |
| |
| config SPI_1_IRQ_PRI |
| int |
| prompt "Port 0 interrupt priority" |
| depends on SPI_1 |
| |
| config SPI_1_DEFAULT_CFG |
| hex "Port 1 default configuration" |
| depends on SPI_1 |
| default 0x80 |
| |
| config SPI_1_DEFAULT_BAUD_RATE |
| int "Port 1 default baud rate" |
| depends on SPI_1 |
| default 500000 |
| |
| config SPI_1_CS_GPIO_PORT |
| string |
| prompt "The GPIO port which is used to control CS" |
| depends on SPI_1 && SPI_CS_GPIO |
| default "GPIO_0" |
| |
| config SPI_1_CS_GPIO_PIN |
| int "The GPIO PIN which is used to act as a CS pin" |
| depends on SPI_1 && SPI_CS_GPIO |
| default 0 |
| |
| config SPI_2 |
| bool |
| prompt "SPI port 2" |
| default n |
| help |
| Enable SPI controller port 2. |
| |
| config SPI_2_NAME |
| string |
| prompt "SPI port 2 device name" |
| depends on SPI_2 |
| default "SPI_2" |
| |
| config SPI_2_IRQ_PRI |
| int |
| prompt "Port 2 interrupt priority" |
| depends on SPI_2 |
| |
| config SPI_2_DEFAULT_CFG |
| hex "Port 2 default configuration" |
| depends on SPI_2 |
| default 0x80 |
| |
| config SPI_2_DEFAULT_BAUD_RATE |
| int "Port 2 default baud rate" |
| depends on SPI_2 |
| default 500000 |
| |
| config SPI_2_CS_GPIO_PORT |
| string |
| prompt "The GPIO port which is used to control CS" |
| depends on SPI_2 && SPI_CS_GPIO |
| default "GPIO_0" |
| |
| config SPI_2_CS_GPIO_PIN |
| int "The GPIO PIN which is used to act as a CS pin" |
| depends on SPI_2 && SPI_CS_GPIO |
| default 0 |
| |
| config SPI_3 |
| bool |
| prompt "SPI port 3" |
| default n |
| help |
| Enable SPI controller port 3. |
| |
| config SPI_3_NAME |
| string |
| prompt "SPI port 3 device name" |
| depends on SPI_3 |
| default "SPI_3" |
| |
| config SPI_3_IRQ_PRI |
| int |
| prompt "Port 3 interrupt priority" |
| depends on SPI_3 |
| |
| config SPI_SS_INIT_PRIORITY |
| int "Init priority" |
| depends on SPI_QMSI_SS |
| default 70 |
| help |
| Device driver initialization priority. |
| |
| config SPI_SS_CS_GPIO |
| bool "SPI port CS pin is controlled via a GPIO port" |
| select GPIO |
| depends on SPI_QMSI_SS |
| default n |
| |
| config SPI_SS_0 |
| bool |
| prompt "SPI SS port 0" |
| depends on SPI_QMSI_SS |
| default n |
| help |
| Enable SPI controller port 0. |
| |
| config SPI_SS_0_NAME |
| string |
| prompt "SPI SS port 0 device name" |
| depends on SPI_SS_0 |
| default "SPI_SS_0" |
| |
| config SPI_SS_0_IRQ_PRI |
| int |
| prompt "Port 0 interrupt priority" |
| depends on SPI_SS_0 |
| |
| config SPI_SS_0_CS_GPIO_PORT |
| string |
| prompt "The GPIO port which is used to control CS" |
| depends on SPI_SS_0 && SPI_SS_CS_GPIO |
| default "GPIO_0" |
| |
| config SPI_SS_0_CS_GPIO_PIN |
| int "The GPIO PIN which is used to act as a CS pin" |
| depends on SPI_SS_0 && SPI_SS_CS_GPIO |
| default 0 |
| |
| config SPI_SS_1 |
| bool |
| prompt "SPI SS port 1" |
| depends on SPI_QMSI_SS |
| default n |
| help |
| Enable SPI controller port 1. |
| |
| config SPI_SS_1_NAME |
| string |
| prompt "SPI port 1 device name" |
| depends on SPI_SS_1 |
| default "SPI_SS_1" |
| |
| config SPI_SS_1_IRQ_PRI |
| int |
| prompt "Port 0 interrupt priority" |
| depends on SPI_SS_1 |
| |
| config SPI_SS_1_CS_GPIO_PORT |
| string |
| prompt "The GPIO port which is used to control CS" |
| depends on SPI_SS_1 && SPI_SS_CS_GPIO |
| default "GPIO_0" |
| |
| config SPI_SS_1_CS_GPIO_PIN |
| int "The GPIO PIN which is used to act as a CS pin" |
| depends on SPI_SS_1 && SPI_SS_CS_GPIO |
| default 0 |
| |
| source "drivers/spi/Kconfig.dw" |
| |
| source "drivers/spi/Kconfig.mcux_dspi" |
| |
| if SPI_LEGACY_API |
| source "drivers/spi/Kconfig.nrf5_legacy" |
| endif |
| |
| endif # SPI |
