| /* |
| * Copyright (c) 2017, I-SENSE group of ICCS |
| * Copyright (c) 2017 Linaro Ltd |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| * |
| * I2C Driver for: STM32F1, STM32F2, STM32F4 and STM32L1 |
| * |
| */ |
| |
| #include <zephyr/drivers/clock_control/stm32_clock_control.h> |
| #include <zephyr/drivers/clock_control.h> |
| #include <zephyr/sys/util.h> |
| #include <zephyr/kernel.h> |
| #include <soc.h> |
| #include <stm32_ll_i2c.h> |
| #include <errno.h> |
| #include <zephyr/drivers/i2c.h> |
| #include "i2c_ll_stm32.h" |
| |
| #define LOG_LEVEL CONFIG_I2C_LOG_LEVEL |
| #include <zephyr/logging/log.h> |
| LOG_MODULE_REGISTER(i2c_ll_stm32_v1); |
| |
| #include "i2c-priv.h" |
| |
| #define STM32_I2C_TRANSFER_TIMEOUT_MSEC 500 |
| |
| #define STM32_I2C_TIMEOUT_USEC 1000 |
| #define I2C_REQUEST_WRITE 0x00 |
| #define I2C_REQUEST_READ 0x01 |
| #define HEADER 0xF0 |
| |
| static void stm32_i2c_generate_start_condition(I2C_TypeDef *i2c) |
| { |
| uint16_t cr1 = LL_I2C_ReadReg(i2c, CR1); |
| |
| if (cr1 & I2C_CR1_STOP) { |
| LOG_DBG("%s: START while STOP active!", __func__); |
| LL_I2C_WriteReg(i2c, CR1, cr1 & ~I2C_CR1_STOP); |
| } |
| |
| LL_I2C_GenerateStartCondition(i2c); |
| } |
| |
| #ifdef CONFIG_I2C_STM32_INTERRUPT |
| |
| static void stm32_i2c_disable_transfer_interrupts(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| LL_I2C_DisableIT_TX(i2c); |
| LL_I2C_DisableIT_RX(i2c); |
| LL_I2C_DisableIT_EVT(i2c); |
| LL_I2C_DisableIT_BUF(i2c); |
| LL_I2C_DisableIT_ERR(i2c); |
| } |
| |
| static void stm32_i2c_enable_transfer_interrupts(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| LL_I2C_EnableIT_ERR(i2c); |
| LL_I2C_EnableIT_EVT(i2c); |
| LL_I2C_EnableIT_BUF(i2c); |
| } |
| |
| #endif /* CONFIG_I2C_STM32_INTERRUPT */ |
| |
| static void stm32_i2c_reset(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| I2C_TypeDef *i2c = cfg->i2c; |
| uint16_t cr1, cr2, oar1, oar2, trise, ccr; |
| #if defined(I2C_FLTR_ANOFF) && defined(I2C_FLTR_DNF) |
| uint16_t fltr; |
| #endif |
| |
| /* disable i2c and disable IRQ's */ |
| LL_I2C_Disable(i2c); |
| #ifdef CONFIG_I2C_STM32_INTERRUPT |
| stm32_i2c_disable_transfer_interrupts(dev); |
| #endif |
| |
| /* save all important registers before reset */ |
| cr1 = LL_I2C_ReadReg(i2c, CR1); |
| cr2 = LL_I2C_ReadReg(i2c, CR2); |
| oar1 = LL_I2C_ReadReg(i2c, OAR1); |
| oar2 = LL_I2C_ReadReg(i2c, OAR2); |
| ccr = LL_I2C_ReadReg(i2c, CCR); |
| trise = LL_I2C_ReadReg(i2c, TRISE); |
| #if defined(I2C_FLTR_ANOFF) && defined(I2C_FLTR_DNF) |
| fltr = LL_I2C_ReadReg(i2c, FLTR); |
| #endif |
| |
| /* reset i2c hardware */ |
| LL_I2C_EnableReset(i2c); |
| LL_I2C_DisableReset(i2c); |
| |
| /* restore all important registers after reset */ |
| LL_I2C_WriteReg(i2c, CR1, cr1); |
| LL_I2C_WriteReg(i2c, CR2, cr2); |
| |
| /* bit 14 of OAR1 must always be 1 */ |
| oar1 |= (1 << 14); |
| LL_I2C_WriteReg(i2c, OAR1, oar1); |
| LL_I2C_WriteReg(i2c, OAR2, oar2); |
| LL_I2C_WriteReg(i2c, CCR, ccr); |
| LL_I2C_WriteReg(i2c, TRISE, trise); |
| #if defined(I2C_FLTR_ANOFF) && defined(I2C_FLTR_DNF) |
| LL_I2C_WriteReg(i2c, FLTR, fltr); |
| #endif |
| } |
| |
| |
| static void stm32_i2c_master_finish(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| #ifdef CONFIG_I2C_STM32_INTERRUPT |
| stm32_i2c_disable_transfer_interrupts(dev); |
| #endif |
| |
| #if defined(CONFIG_I2C_TARGET) |
| struct i2c_stm32_data *data = dev->data; |
| data->master_active = false; |
| if (!data->slave_attached) { |
| LL_I2C_Disable(i2c); |
| } else { |
| stm32_i2c_enable_transfer_interrupts(dev); |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_ACK); |
| } |
| #else |
| LL_I2C_Disable(i2c); |
| #endif |
| } |
| |
| static inline void msg_init(const struct device *dev, struct i2c_msg *msg, |
| uint8_t *next_msg_flags, uint16_t slave, |
| uint32_t transfer) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| ARG_UNUSED(next_msg_flags); |
| |
| #ifdef CONFIG_I2C_STM32_INTERRUPT |
| k_sem_reset(&data->device_sync_sem); |
| #endif |
| |
| data->current.len = msg->len; |
| data->current.buf = msg->buf; |
| data->current.flags = msg->flags; |
| data->current.is_restart = 0U; |
| data->current.is_write = (transfer == I2C_REQUEST_WRITE); |
| data->current.is_arlo = 0U; |
| data->current.is_err = 0U; |
| data->current.is_nack = 0U; |
| data->current.msg = msg; |
| #if defined(CONFIG_I2C_TARGET) |
| data->master_active = true; |
| #endif |
| data->slave_address = slave; |
| |
| LL_I2C_Enable(i2c); |
| |
| LL_I2C_DisableBitPOS(i2c); |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_ACK); |
| if (msg->flags & I2C_MSG_RESTART) { |
| stm32_i2c_generate_start_condition(i2c); |
| } |
| } |
| |
| static int32_t msg_end(const struct device *dev, uint8_t *next_msg_flags, |
| const char *funcname) |
| { |
| struct i2c_stm32_data *data = dev->data; |
| |
| if (data->current.is_nack || data->current.is_err || |
| data->current.is_arlo) { |
| goto error; |
| } |
| |
| if (!next_msg_flags) { |
| stm32_i2c_master_finish(dev); |
| } |
| |
| return 0; |
| |
| error: |
| if (data->current.is_arlo) { |
| LOG_DBG("%s: ARLO %d", funcname, |
| data->current.is_arlo); |
| data->current.is_arlo = 0U; |
| } |
| |
| if (data->current.is_nack) { |
| LOG_DBG("%s: NACK", funcname); |
| data->current.is_nack = 0U; |
| } |
| |
| if (data->current.is_err) { |
| LOG_DBG("%s: ERR %d", funcname, |
| data->current.is_err); |
| data->current.is_err = 0U; |
| } |
| stm32_i2c_master_finish(dev); |
| |
| return -EIO; |
| } |
| |
| #ifdef CONFIG_I2C_STM32_INTERRUPT |
| |
| static void stm32_i2c_master_mode_end(const struct device *dev) |
| { |
| struct i2c_stm32_data *data = dev->data; |
| |
| k_sem_give(&data->device_sync_sem); |
| } |
| |
| static inline void handle_sb(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| uint16_t saddr = data->slave_address; |
| uint8_t slave; |
| |
| if (I2C_ADDR_10_BITS & data->dev_config) { |
| slave = (((saddr & 0x0300) >> 7) & 0xFF); |
| uint8_t header = slave | HEADER; |
| |
| if (data->current.is_restart == 0U) { |
| data->current.is_restart = 1U; |
| } else { |
| header |= I2C_REQUEST_READ; |
| data->current.is_restart = 0U; |
| } |
| LL_I2C_TransmitData8(i2c, header); |
| |
| return; |
| } |
| slave = (saddr << 1) & 0xFF; |
| if (data->current.is_write) { |
| LL_I2C_TransmitData8(i2c, slave | I2C_REQUEST_WRITE); |
| } else { |
| LL_I2C_TransmitData8(i2c, slave | I2C_REQUEST_READ); |
| if (data->current.len == 2) { |
| LL_I2C_EnableBitPOS(i2c); |
| } |
| } |
| } |
| |
| static inline void handle_addr(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| if (I2C_ADDR_10_BITS & data->dev_config) { |
| if (!data->current.is_write && data->current.is_restart) { |
| data->current.is_restart = 0U; |
| LL_I2C_ClearFlag_ADDR(i2c); |
| stm32_i2c_generate_start_condition(i2c); |
| |
| return; |
| } |
| } |
| |
| if (data->current.is_write) { |
| LL_I2C_ClearFlag_ADDR(i2c); |
| return; |
| } |
| /* according to STM32F1 errata we need to handle these corner cases in |
| * specific way. |
| * Please ref to STM32F10xxC/D/E I2C peripheral Errata sheet 2.14.1 |
| */ |
| if (data->current.len == 0U && IS_ENABLED(CONFIG_SOC_SERIES_STM32F1X)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| } else if (data->current.len == 1U) { |
| /* Single byte reception: enable NACK and clear POS */ |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); |
| #ifdef CONFIG_SOC_SERIES_STM32F1X |
| LL_I2C_ClearFlag_ADDR(i2c); |
| LL_I2C_GenerateStopCondition(i2c); |
| #endif |
| } else if (data->current.len == 2U) { |
| #ifdef CONFIG_SOC_SERIES_STM32F1X |
| LL_I2C_ClearFlag_ADDR(i2c); |
| #endif |
| /* 2-byte reception: enable NACK and set POS */ |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); |
| LL_I2C_EnableBitPOS(i2c); |
| } |
| LL_I2C_ClearFlag_ADDR(i2c); |
| } |
| |
| static inline void handle_txe(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| if (data->current.len) { |
| data->current.len--; |
| if (data->current.len == 0U) { |
| /* |
| * This is the last byte to transmit disable Buffer |
| * interrupt and wait for a BTF interrupt |
| */ |
| LL_I2C_DisableIT_BUF(i2c); |
| } |
| LL_I2C_TransmitData8(i2c, *data->current.buf); |
| data->current.buf++; |
| } else { |
| if (data->current.flags & I2C_MSG_STOP) { |
| LL_I2C_GenerateStopCondition(i2c); |
| } |
| if (LL_I2C_IsActiveFlag_BTF(i2c)) { |
| /* Read DR to clear BTF flag */ |
| LL_I2C_ReceiveData8(i2c); |
| } |
| |
| k_sem_give(&data->device_sync_sem); |
| } |
| } |
| |
| static inline void handle_rxne(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| if (data->current.len > 0) { |
| switch (data->current.len) { |
| case 1: |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); |
| LL_I2C_DisableBitPOS(i2c); |
| /* Single byte reception */ |
| if (data->current.flags & I2C_MSG_STOP) { |
| LL_I2C_GenerateStopCondition(i2c); |
| } |
| LL_I2C_DisableIT_BUF(i2c); |
| data->current.len--; |
| *data->current.buf = LL_I2C_ReceiveData8(i2c); |
| data->current.buf++; |
| |
| k_sem_give(&data->device_sync_sem); |
| break; |
| case 2: |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); |
| LL_I2C_EnableBitPOS(i2c); |
| __fallthrough; |
| case 3: |
| /* |
| * 2-byte, 3-byte reception and for N-2, N-1, |
| * N when N > 3 |
| */ |
| LL_I2C_DisableIT_BUF(i2c); |
| break; |
| default: |
| /* N byte reception when N > 3 */ |
| data->current.len--; |
| *data->current.buf = LL_I2C_ReceiveData8(i2c); |
| data->current.buf++; |
| } |
| } else { |
| |
| if (data->current.flags & I2C_MSG_STOP) { |
| LL_I2C_GenerateStopCondition(i2c); |
| } |
| k_sem_give(&data->device_sync_sem); |
| } |
| } |
| |
| static inline void handle_btf(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| if (data->current.is_write) { |
| handle_txe(dev); |
| } else { |
| uint32_t counter = 0U; |
| |
| switch (data->current.len) { |
| case 2: |
| /* |
| * Stop condition must be generated before reading the |
| * last two bytes. |
| */ |
| if (data->current.flags & I2C_MSG_STOP) { |
| LL_I2C_GenerateStopCondition(i2c); |
| } |
| |
| for (counter = 2U; counter > 0; counter--) { |
| data->current.len--; |
| *data->current.buf = LL_I2C_ReceiveData8(i2c); |
| data->current.buf++; |
| } |
| k_sem_give(&data->device_sync_sem); |
| break; |
| case 3: |
| /* Set NACK before reading N-2 byte*/ |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); |
| data->current.len--; |
| *data->current.buf = LL_I2C_ReceiveData8(i2c); |
| data->current.buf++; |
| break; |
| default: |
| handle_rxne(dev); |
| } |
| } |
| } |
| |
| |
| #if defined(CONFIG_I2C_TARGET) |
| static void stm32_i2c_slave_event(const struct device *dev) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| const struct i2c_target_callbacks *slave_cb = |
| data->slave_cfg->callbacks; |
| |
| if (LL_I2C_IsActiveFlag_TXE(i2c) && LL_I2C_IsActiveFlag_BTF(i2c)) { |
| uint8_t val; |
| slave_cb->read_processed(data->slave_cfg, &val); |
| LL_I2C_TransmitData8(i2c, val); |
| return; |
| } |
| |
| if (LL_I2C_IsActiveFlag_RXNE(i2c)) { |
| uint8_t val = LL_I2C_ReceiveData8(i2c); |
| if (slave_cb->write_received(data->slave_cfg, val)) { |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); |
| } |
| return; |
| } |
| |
| if (LL_I2C_IsActiveFlag_AF(i2c)) { |
| LL_I2C_ClearFlag_AF(i2c); |
| } |
| |
| if (LL_I2C_IsActiveFlag_STOP(i2c)) { |
| LL_I2C_ClearFlag_STOP(i2c); |
| slave_cb->stop(data->slave_cfg); |
| /* Prepare to ACK next transmissions address byte */ |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_ACK); |
| } |
| |
| if (LL_I2C_IsActiveFlag_ADDR(i2c)) { |
| uint32_t dir = LL_I2C_GetTransferDirection(i2c); |
| if (dir == LL_I2C_DIRECTION_READ) { |
| slave_cb->write_requested(data->slave_cfg); |
| LL_I2C_EnableIT_RX(i2c); |
| } else { |
| uint8_t val; |
| slave_cb->read_requested(data->slave_cfg, &val); |
| LL_I2C_TransmitData8(i2c, val); |
| LL_I2C_EnableIT_TX(i2c); |
| } |
| |
| stm32_i2c_enable_transfer_interrupts(dev); |
| } |
| } |
| |
| /* Attach and start I2C as slave */ |
| int i2c_stm32_target_register(const struct device *dev, struct i2c_target_config *config) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| uint32_t bitrate_cfg; |
| int ret; |
| |
| if (!config) { |
| return -EINVAL; |
| } |
| |
| if (data->slave_attached) { |
| return -EBUSY; |
| } |
| |
| if (data->master_active) { |
| return -EBUSY; |
| } |
| |
| bitrate_cfg = i2c_map_dt_bitrate(cfg->bitrate); |
| |
| ret = i2c_stm32_runtime_configure(dev, bitrate_cfg); |
| if (ret < 0) { |
| LOG_ERR("i2c: failure initializing"); |
| return ret; |
| } |
| |
| data->slave_cfg = config; |
| |
| LL_I2C_Enable(i2c); |
| |
| if (data->slave_cfg->flags == I2C_TARGET_FLAGS_ADDR_10_BITS) { |
| return -ENOTSUP; |
| } |
| LL_I2C_SetOwnAddress1(i2c, config->address << 1U, LL_I2C_OWNADDRESS1_7BIT); |
| data->slave_attached = true; |
| |
| LOG_DBG("i2c: target registered"); |
| |
| stm32_i2c_enable_transfer_interrupts(dev); |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_ACK); |
| |
| return 0; |
| } |
| |
| int i2c_stm32_target_unregister(const struct device *dev, struct i2c_target_config *config) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| if (!data->slave_attached) { |
| return -EINVAL; |
| } |
| |
| if (data->master_active) { |
| return -EBUSY; |
| } |
| |
| stm32_i2c_disable_transfer_interrupts(dev); |
| |
| LL_I2C_ClearFlag_AF(i2c); |
| LL_I2C_ClearFlag_STOP(i2c); |
| LL_I2C_ClearFlag_ADDR(i2c); |
| |
| LL_I2C_Disable(i2c); |
| |
| data->slave_attached = false; |
| |
| LOG_DBG("i2c: slave unregistered"); |
| |
| return 0; |
| } |
| #endif /* defined(CONFIG_I2C_TARGET) */ |
| |
| void stm32_i2c_event_isr(void *arg) |
| { |
| const struct device *dev = (const struct device *)arg; |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| #if defined(CONFIG_I2C_TARGET) |
| if (data->slave_attached && !data->master_active) { |
| stm32_i2c_slave_event(dev); |
| return; |
| } |
| #endif |
| |
| if (LL_I2C_IsActiveFlag_SB(i2c)) { |
| handle_sb(dev); |
| } else if (LL_I2C_IsActiveFlag_ADD10(i2c)) { |
| LL_I2C_TransmitData8(i2c, data->slave_address); |
| } else if (LL_I2C_IsActiveFlag_ADDR(i2c)) { |
| handle_addr(dev); |
| } else if (LL_I2C_IsActiveFlag_BTF(i2c)) { |
| handle_btf(dev); |
| } else if (LL_I2C_IsActiveFlag_TXE(i2c) && data->current.is_write) { |
| handle_txe(dev); |
| } else if (LL_I2C_IsActiveFlag_RXNE(i2c) && !data->current.is_write) { |
| handle_rxne(dev); |
| } |
| } |
| |
| void stm32_i2c_error_isr(void *arg) |
| { |
| const struct device *dev = (const struct device *)arg; |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| #if defined(CONFIG_I2C_TARGET) |
| if (data->slave_attached && !data->master_active) { |
| /* No need for a slave error function right now. */ |
| return; |
| } |
| #endif |
| |
| if (LL_I2C_IsActiveFlag_AF(i2c)) { |
| LL_I2C_ClearFlag_AF(i2c); |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_nack = 1U; |
| goto end; |
| } |
| if (LL_I2C_IsActiveFlag_ARLO(i2c)) { |
| LL_I2C_ClearFlag_ARLO(i2c); |
| data->current.is_arlo = 1U; |
| goto end; |
| } |
| |
| if (LL_I2C_IsActiveFlag_BERR(i2c)) { |
| LL_I2C_ClearFlag_BERR(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| return; |
| end: |
| stm32_i2c_master_mode_end(dev); |
| } |
| |
| int32_t stm32_i2c_msg_write(const struct device *dev, struct i2c_msg *msg, |
| uint8_t *next_msg_flags, uint16_t saddr) |
| { |
| struct i2c_stm32_data *data = dev->data; |
| |
| msg_init(dev, msg, next_msg_flags, saddr, I2C_REQUEST_WRITE); |
| |
| stm32_i2c_enable_transfer_interrupts(dev); |
| |
| if (k_sem_take(&data->device_sync_sem, |
| K_MSEC(STM32_I2C_TRANSFER_TIMEOUT_MSEC)) != 0) { |
| LOG_DBG("%s: WRITE timeout", __func__); |
| stm32_i2c_reset(dev); |
| return -EIO; |
| } |
| |
| return msg_end(dev, next_msg_flags, __func__); |
| } |
| |
| int32_t stm32_i2c_msg_read(const struct device *dev, struct i2c_msg *msg, |
| uint8_t *next_msg_flags, uint16_t saddr) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| msg_init(dev, msg, next_msg_flags, saddr, I2C_REQUEST_READ); |
| |
| stm32_i2c_enable_transfer_interrupts(dev); |
| LL_I2C_EnableIT_RX(i2c); |
| |
| if (k_sem_take(&data->device_sync_sem, |
| K_MSEC(STM32_I2C_TRANSFER_TIMEOUT_MSEC)) != 0) { |
| LOG_DBG("%s: READ timeout", __func__); |
| stm32_i2c_reset(dev); |
| return -EIO; |
| } |
| |
| return msg_end(dev, next_msg_flags, __func__); |
| } |
| |
| #else /* CONFIG_I2C_STM32_INTERRUPT */ |
| |
| static inline int check_errors(const struct device *dev, const char *funcname) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| if (LL_I2C_IsActiveFlag_AF(i2c)) { |
| LL_I2C_ClearFlag_AF(i2c); |
| LOG_DBG("%s: NACK", funcname); |
| data->current.is_nack = 1U; |
| goto error; |
| } |
| |
| if (LL_I2C_IsActiveFlag_ARLO(i2c)) { |
| LL_I2C_ClearFlag_ARLO(i2c); |
| LOG_DBG("%s: ARLO", funcname); |
| data->current.is_arlo = 1U; |
| goto error; |
| } |
| |
| if (LL_I2C_IsActiveFlag_OVR(i2c)) { |
| LL_I2C_ClearFlag_OVR(i2c); |
| LOG_DBG("%s: OVR", funcname); |
| data->current.is_err = 1U; |
| goto error; |
| } |
| |
| if (LL_I2C_IsActiveFlag_BERR(i2c)) { |
| LL_I2C_ClearFlag_BERR(i2c); |
| LOG_DBG("%s: BERR", funcname); |
| data->current.is_err = 1U; |
| goto error; |
| } |
| |
| return 0; |
| error: |
| return -EIO; |
| } |
| |
| static int stm32_i2c_wait_timeout(uint16_t *timeout) |
| { |
| if (*timeout == 0) { |
| return 1; |
| } else { |
| k_busy_wait(1); |
| (*timeout)--; |
| return 0; |
| } |
| } |
| |
| int32_t stm32_i2c_msg_write(const struct device *dev, struct i2c_msg *msg, |
| uint8_t *next_msg_flags, uint16_t saddr) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| uint32_t len = msg->len; |
| uint16_t timeout; |
| uint8_t *buf = msg->buf; |
| int32_t res; |
| |
| msg_init(dev, msg, next_msg_flags, saddr, I2C_REQUEST_WRITE); |
| |
| if (msg->flags & I2C_MSG_RESTART) { |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_SB(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| if (I2C_ADDR_10_BITS & data->dev_config) { |
| uint8_t slave = (((saddr & 0x0300) >> 7) & 0xFF); |
| uint8_t header = slave | HEADER; |
| |
| LL_I2C_TransmitData8(i2c, header); |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_ADD10(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| slave = data->slave_address & 0xFF; |
| LL_I2C_TransmitData8(i2c, slave); |
| } else { |
| uint8_t slave = (saddr << 1) & 0xFF; |
| |
| LL_I2C_TransmitData8(i2c, slave | I2C_REQUEST_WRITE); |
| } |
| |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_ADDR(i2c)) { |
| if (LL_I2C_IsActiveFlag_AF(i2c) || stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_ClearFlag_AF(i2c); |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_nack = 1U; |
| goto end; |
| } |
| } |
| LL_I2C_ClearFlag_ADDR(i2c); |
| } |
| |
| while (len) { |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (1) { |
| if (LL_I2C_IsActiveFlag_TXE(i2c)) { |
| break; |
| } |
| if (LL_I2C_IsActiveFlag_AF(i2c) || stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_ClearFlag_AF(i2c); |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_nack = 1U; |
| goto end; |
| } |
| } |
| LL_I2C_TransmitData8(i2c, *buf); |
| buf++; |
| len--; |
| } |
| |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_BTF(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| if (msg->flags & I2C_MSG_STOP) { |
| LL_I2C_GenerateStopCondition(i2c); |
| } |
| |
| end: |
| check_errors(dev, __func__); |
| res = msg_end(dev, next_msg_flags, __func__); |
| if (res < 0) { |
| stm32_i2c_reset(dev); |
| } |
| |
| return res; |
| } |
| |
| int32_t stm32_i2c_msg_read(const struct device *dev, struct i2c_msg *msg, |
| uint8_t *next_msg_flags, uint16_t saddr) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| uint32_t len = msg->len; |
| uint16_t timeout; |
| uint8_t *buf = msg->buf; |
| int32_t res; |
| |
| msg_init(dev, msg, next_msg_flags, saddr, I2C_REQUEST_READ); |
| |
| if (msg->flags & I2C_MSG_RESTART) { |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_SB(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| if (I2C_ADDR_10_BITS & data->dev_config) { |
| uint8_t slave = (((saddr & 0x0300) >> 7) & 0xFF); |
| uint8_t header = slave | HEADER; |
| |
| LL_I2C_TransmitData8(i2c, header); |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_ADD10(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| slave = saddr & 0xFF; |
| LL_I2C_TransmitData8(i2c, slave); |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_ADDR(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| LL_I2C_ClearFlag_ADDR(i2c); |
| stm32_i2c_generate_start_condition(i2c); |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_SB(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| header |= I2C_REQUEST_READ; |
| LL_I2C_TransmitData8(i2c, header); |
| } else { |
| uint8_t slave = ((saddr) << 1) & 0xFF; |
| |
| LL_I2C_TransmitData8(i2c, slave | I2C_REQUEST_READ); |
| } |
| |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_ADDR(i2c)) { |
| if (LL_I2C_IsActiveFlag_AF(i2c) || stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_ClearFlag_AF(i2c); |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_nack = 1U; |
| goto end; |
| } |
| } |
| /* ADDR must be cleared before NACK generation. Either in 2 byte reception |
| * byte 1 will be NACK'ed and slave wont sent the last byte |
| */ |
| LL_I2C_ClearFlag_ADDR(i2c); |
| if (len == 1U) { |
| /* Single byte reception: enable NACK and set STOP */ |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); |
| } else if (len == 2U) { |
| /* 2-byte reception: enable NACK and set POS */ |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); |
| LL_I2C_EnableBitPOS(i2c); |
| } |
| } |
| |
| while (len) { |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| while (!LL_I2C_IsActiveFlag_RXNE(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| timeout = STM32_I2C_TIMEOUT_USEC; |
| switch (len) { |
| case 1: |
| if (msg->flags & I2C_MSG_STOP) { |
| LL_I2C_GenerateStopCondition(i2c); |
| } |
| len--; |
| *buf = LL_I2C_ReceiveData8(i2c); |
| buf++; |
| break; |
| case 2: |
| while (!LL_I2C_IsActiveFlag_BTF(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| /* |
| * Stop condition must be generated before reading the |
| * last two bytes. |
| */ |
| if (msg->flags & I2C_MSG_STOP) { |
| LL_I2C_GenerateStopCondition(i2c); |
| } |
| |
| for (uint32_t counter = 2; counter > 0; counter--) { |
| len--; |
| *buf = LL_I2C_ReceiveData8(i2c); |
| buf++; |
| } |
| |
| break; |
| case 3: |
| while (!LL_I2C_IsActiveFlag_BTF(i2c)) { |
| if (stm32_i2c_wait_timeout(&timeout)) { |
| LL_I2C_GenerateStopCondition(i2c); |
| data->current.is_err = 1U; |
| goto end; |
| } |
| } |
| |
| /* Set NACK before reading N-2 byte*/ |
| LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); |
| __fallthrough; |
| default: |
| len--; |
| *buf = LL_I2C_ReceiveData8(i2c); |
| buf++; |
| } |
| } |
| end: |
| check_errors(dev, __func__); |
| res = msg_end(dev, next_msg_flags, __func__); |
| if (res < 0) { |
| stm32_i2c_reset(dev); |
| } |
| |
| return res; |
| } |
| #endif /* CONFIG_I2C_STM32_INTERRUPT */ |
| |
| int32_t stm32_i2c_configure_timing(const struct device *dev, uint32_t clock) |
| { |
| const struct i2c_stm32_config *cfg = dev->config; |
| struct i2c_stm32_data *data = dev->data; |
| I2C_TypeDef *i2c = cfg->i2c; |
| |
| switch (I2C_SPEED_GET(data->dev_config)) { |
| case I2C_SPEED_STANDARD: |
| LL_I2C_ConfigSpeed(i2c, clock, 100000, LL_I2C_DUTYCYCLE_2); |
| break; |
| case I2C_SPEED_FAST: |
| LL_I2C_ConfigSpeed(i2c, clock, 400000, LL_I2C_DUTYCYCLE_2); |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |