| # STM32 HAL Ethernet driver configuration options |
| |
| # Copyright (c) 2017 Erwin Rol <erwin@erwinrol.com> |
| # Copyright (c) 2020 Alexander Kozhinov <AlexanderKozhinov@yandex.com> |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| DT_COMPAT_ST_STM32_ETHERNET := st,stm32-ethernet |
| |
| menuconfig ETH_STM32_HAL |
| bool "STM32 HAL Ethernet driver" |
| default y if $(dt_compat_enabled,$(DT_COMPAT_ST_STM32_ETHERNET)) |
| select USE_STM32_HAL_ETH |
| select NOCACHE_MEMORY if SOC_SERIES_STM32H7X && CPU_CORTEX_M7 |
| help |
| Enable STM32 HAL based Ethernet driver. It is available for |
| all Ethernet enabled variants of the F2, F4, F7 and H7 series. |
| |
| if ETH_STM32_HAL |
| |
| config ETH_STM32_HAL_RX_THREAD_STACK_SIZE |
| int "RX thread stack size" |
| default 1500 |
| help |
| RX thread stack size |
| |
| config ETH_STM32_HAL_RX_THREAD_PRIO |
| int "RX thread priority" |
| default 2 |
| help |
| RX thread priority |
| |
| config ETH_STM32_HAL_USE_DTCM_FOR_DMA_BUFFER |
| bool "Use DTCM for DMA buffers" |
| default y |
| depends on SOC_SERIES_STM32F7X |
| help |
| When this option is activated, the buffers for DMA transfer are |
| moved from SRAM to the DTCM (Data Tightly Coupled Memory). |
| |
| config ETH_STM32_HAL_PHY_ADDRESS |
| int "Phy address" |
| default 0 |
| help |
| The phy address to use. |
| |
| config ETH_STM32_HAL_RANDOM_MAC |
| bool "Random MAC address" |
| depends on ENTROPY_GENERATOR |
| default y |
| help |
| Generate a random MAC address dynamically. |
| |
| if !ETH_STM32_HAL_RANDOM_MAC |
| |
| config ETH_STM32_HAL_MAC3 |
| hex "MAC Address Byte 3" |
| default 0 |
| range 0 0xff |
| help |
| This is the byte 3 of the MAC address. |
| |
| config ETH_STM32_HAL_MAC4 |
| hex "MAC Address Byte 4" |
| default 0 |
| range 0 0xff |
| help |
| This is the byte 4 of the MAC address. |
| |
| config ETH_STM32_HAL_MAC5 |
| hex "MAC Address Byte 5" |
| default 0 |
| range 0 0xff |
| help |
| This is the byte 5 of the MAC address. |
| |
| endif # !ETH_STM32_HAL_RANDOM_MAC |
| |
| config ETH_STM32_HAL_MII |
| bool "Use MII interface" |
| help |
| Use the MII physical interface instead of RMII. |
| |
| config ETH_STM32_CARRIER_CHECK_RX_IDLE_TIMEOUT_MS |
| int "Carrier check timeout period (ms)" |
| default 500 |
| range 100 30000 |
| help |
| Set the RX idle timeout period in milliseconds after which the |
| PHY's carrier status is re-evaluated. |
| |
| config ETH_STM32_AUTO_NEGOTIATION_ENABLE |
| bool "Enable autonegotiation mode" |
| default y |
| help |
| Enable this if using autonegotiation |
| |
| if !ETH_STM32_AUTO_NEGOTIATION_ENABLE |
| |
| config ETH_STM32_SPEED_10M |
| bool "Enable this if using 10 Mbps for speed when autonegotiation is diabled" |
| default n |
| help |
| Set this if using 10 Mbps and when autonegotiation is disabled, otherwise speed |
| is 100 Mbps |
| |
| config ETH_STM32_MODE_HALFDUPLEX |
| bool "Enable this if using half duplex" |
| default n |
| help |
| Set this if using half duplex when autonegotiation is disabled otherwise |
| duplex mode is full duplex |
| |
| endif # !ETH_STM32_AUTO_NEGOTIATION_ENABLE |
| |
| endif # ETH_STM32_HAL |
