| # Kconfig.tmp007 - TMP007 infrared thermopile sensor configuration options |
| |
| # |
| # Copyright (c) 2016 Intel Corporation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| menuconfig TMP007 |
| bool |
| prompt "TMP007 Infrared Thermopile Sensor" |
| depends on SENSOR && I2C |
| default n |
| help |
| Enable driver for TMP007 infrared thermopile sensors. |
| |
| config TMP007_SYS_LOG_LEVEL |
| int "TMP007 Log level" |
| depends on SYS_LOG && TMP007 |
| default 0 |
| range 0 4 |
| help |
| Sets log level for TMP007 driver. |
| Levels are: |
| |
| - 0 OFF: do not write |
| |
| - 1 ERROR: only write SYS_LOG_ERR |
| |
| - 2 WARNING: write SYS_LOG_WRN in addition to previous level |
| |
| - 3 INFO: write SYS_LOG_INF in addition to previous levels |
| |
| - 4 DEBUG: write SYS_LOG_DBG in addition to previous levels |
| |
| config TMP007_NAME |
| string |
| prompt "Driver name" |
| default "TMP007" |
| depends on TMP007 |
| help |
| Device name with which the TMP007 sensor is identified. |
| |
| config TMP007_INIT_PRIORITY |
| int |
| prompt "Init priority" |
| depends on TMP007 |
| default 70 |
| help |
| Device driver initialization priority. |
| |
| choice |
| prompt "I2C address" |
| depends on TMP007 |
| default TMP007_I2C_ADDR_0 |
| help |
| I2C address of the TMP007 sensor. |
| |
| config TMP007_I2C_ADDR_0 |
| bool |
| prompt "0x40" |
| help |
| A0 connected GND and A1 connected to GND. |
| |
| config TMP007_I2C_ADDR_1 |
| bool |
| prompt "0x41" |
| help |
| A0 connected VDD and A1 connected to GND. |
| |
| config TMP007_I2C_ADDR_2 |
| bool |
| prompt "0x42" |
| help |
| A0 connected SDA and A1 connected to GND. |
| |
| config TMP007_I2C_ADDR_3 |
| bool |
| prompt "0x43" |
| help |
| A0 connected SCL and A1 connected to GND. |
| |
| config TMP007_I2C_ADDR_4 |
| bool |
| prompt "0x44" |
| help |
| A0 connected GND and A1 connected to VDD. |
| |
| config TMP007_I2C_ADDR_5 |
| bool |
| prompt "0x45" |
| help |
| A0 connected VDD and A1 connected to VDD. |
| |
| config TMP007_I2C_ADDR_6 |
| bool |
| prompt "0x46" |
| help |
| A0 connected SDA and A1 connected to VDD. |
| |
| config TMP007_I2C_ADDR_7 |
| bool |
| prompt "0x47" |
| help |
| A0 connected SCL and A1 connected to VDD. |
| |
| endchoice |
| |
| config TMP007_I2C_MASTER_DEV_NAME |
| string |
| prompt "I2C master where TMP007 is connected" |
| depends on TMP007 |
| default "I2C_0" |
| help |
| Specify the device name of the I2C master device to which the |
| TMP007 chip is connected. |
| |
| choice |
| prompt "Trigger mode" |
| depends on TMP007 |
| default TMP007_TRIGGER_NONE |
| help |
| Specify the type of triggering to be used by the driver. |
| |
| config TMP007_TRIGGER_NONE |
| bool |
| prompt "No trigger" |
| |
| config TMP007_TRIGGER_GLOBAL_FIBER |
| bool |
| prompt "Use global fiber" |
| depends on GPIO && SYSTEM_WORKQUEUE |
| select TMP007_TRIGGER |
| |
| config TMP007_TRIGGER_OWN_FIBER |
| bool |
| prompt "Use own fiber" |
| depends on GPIO |
| select TMP007_TRIGGER |
| |
| endchoice |
| |
| config TMP007_TRIGGER |
| bool |
| depends on TMP007 |
| |
| config TMP007_GPIO_DEV_NAME |
| string |
| prompt "GPIO device" |
| default "GPIO_0" |
| depends on TMP007 && TMP007_TRIGGER |
| help |
| The device name of the GPIO device to which the TMP007 interrupt |
| (alert) pin is connected. |
| |
| config TMP007_GPIO_PIN_NUM |
| int |
| prompt "Interrupt GPIO pin number" |
| default 0 |
| depends on TMP007 && TMP007_TRIGGER |
| help |
| The number of the GPIO pin on which the interrupt signal from the |
| TMP007 chip will be received. |
| |
| config TMP007_FIBER_PRIORITY |
| int |
| prompt "Fiber priority" |
| depends on TMP007 && TMP007_TRIGGER_OWN_FIBER |
| default 10 |
| help |
| Priority of fiber used by the driver to handle interrupts. |
| |
| config TMP007_FIBER_STACK_SIZE |
| int |
| prompt "Fiber stack size" |
| depends on TMP007 && TMP007_TRIGGER_OWN_FIBER |
| default 1024 |
| help |
| Stack size of fiber used by the driver to handle interrupts. |