boards/arm/nrf9160dk_nrf9160/doc/index.rst - third_party/github/zephyrproject-rtos/zephyr - Git at Google

 .. _nrf9160dk_nrf9160:

 nRF9160 DK
 ##########

 Overview
 ********

 The nRF9160 DK (PCA10090) is a single-board development kit for evaluation and
 development on the nRF9160 SiP for LTE-M and NB-IoT. The nrf9160dk_nrf9160
 board configuration provides support for the Nordic Semiconductor nRF9160 ARM
 Cortex-M33F CPU with ARMv8-M Security Extension and the following devices:

 * :abbr:`ADC (Analog to Digital Converter)`
 * CLOCK
 * FLASH
 * :abbr:`GPIO (General Purpose Input Output)`
 * :abbr:`I2C (Inter-Integrated Circuit)`
 * :abbr:`MPU (Memory Protection Unit)`
 * :abbr:`NVIC (Nested Vectored Interrupt Controller)`
 * :abbr:`PWM (Pulse Width Modulation)`
 * :abbr:`RTC (nRF RTC System Clock)`
 * Segger RTT (RTT Console)
 * :abbr:`SPI (Serial Peripheral Interface)`
 * :abbr:`UARTE (Universal asynchronous receiver-transmitter with EasyDMA)`
 * :abbr:`WDT (Watchdog Timer)`
 * :abbr:`IDAU (Implementation Defined Attribution Unit)`

 .. figure:: img/nrf9160dk_nrf9160.jpg
      :align: center
      :alt: nRF9160 DK

      nRF9160 DK (Credit: Nordic Semiconductor)

 More information about the board can be found at the
 `nRF9160 DK website`_. The `Nordic Semiconductor Infocenter`_
 contains the processor's information and the datasheet.


 Hardware
 ********

 nRF9160 DK has two external oscillators. The frequency of
 the slow clock is 32.768 kHz. The frequency of the main clock
 is 32 MHz.

 Supported Features
 ==================

 The nrf9160dk_nrf9160 board configuration supports the following
 hardware features:

 +-----------+------------+----------------------+
 | Interface | Controller | Driver/Component     |
 +===========+============+======================+
 | ADC       | on-chip    | adc                  |
 +-----------+------------+----------------------+
 | CLOCK     | on-chip    | clock_control        |
 +-----------+------------+----------------------+
 | FLASH     | on-chip    | flash                |
 +-----------+------------+----------------------+
 | GPIO      | on-chip    | gpio                 |
 +-----------+------------+----------------------+
 | I2C(M)    | on-chip    | i2c                  |
 +-----------+------------+----------------------+
 | MPU       | on-chip    | arch/arm             |
 +-----------+------------+----------------------+
 | NVIC      | on-chip    | arch/arm             |
 +-----------+------------+----------------------+
 | PWM       | on-chip    | pwm                  |
 +-----------+------------+----------------------+
 | RTC       | on-chip    | system clock         |
 +-----------+------------+----------------------+
 | RTT       | Segger     | console              |
 +-----------+------------+----------------------+
 | SPI(M/S)  | on-chip    | spi                  |
 +-----------+------------+----------------------+
 | SPU       | on-chip    | system protection    |
 +-----------+------------+----------------------+
 | UARTE     | on-chip    | serial               |
 +-----------+------------+----------------------+
 | WDT       | on-chip    | watchdog             |
 +-----------+------------+----------------------+

 .. _nrf9160dk_additional_hardware:

 Additional hardware in v0.14.0+
 -------------------------------

 Starting from v0.14.0, additional hardware is available on the DK:

 * External flash memory (MX25R6435F, 64 Mb)
 * I/O expander (PCAL6408A) that can be used to interface LEDs, slide switches,
   and buttons

 To use this additional hardware, specify the revision of the board that
 should be used when building your application (for more information, see
 :ref:`application_board_version`). For example, to build for nRF9160 DK v1.0.0:

 .. zephyr-app-commands::
    :tool: all
    :cd-into:
    :board: nrf9160dk_nrf9160@1.0.0
    :goals: build
    :compact:

 Remember to also enable routing for this additional hardware in the firmware for
 :ref:`nrf9160dk_nrf52840` (see :ref:`nrf9160dk_board_controller_firmware`).

 Other hardware features have not been enabled yet for this board.
 See `nRF9160 DK website`_ and `Nordic Semiconductor Infocenter`_
 for a complete list of nRF9160 DK board hardware features.

 Connections and IOs
 ===================

 LED
 ---

 * LED1 (green) = P0.2
 * LED2 (green) = P0.3
 * LED3 (green) = P0.4
 * LED4 (green) = P0.5

 Push buttons and Switches
 -------------------------

 * BUTTON1 = P0.6
 * BUTTON2 = P0.7
 * SWITCH1 = P0.8
 * SWITCH2 = P0.9
 * BOOT = SW5 = boot/reset

 Security components
 ===================

 - Implementation Defined Attribution Unit (`IDAU`_).  The IDAU is implemented
   with the System Protection Unit and is used to define secure and non-secure
   memory maps.  By default, all of the memory space  (Flash, SRAM, and
   peripheral address space) is defined to be secure accessible only.
 - Secure boot.


 Programming and Debugging
 *************************

 nrf9160dk_nrf9160 supports the Armv8m Security Extension, and by default boots
 in the Secure state.

 Building Secure/Non-Secure Zephyr applications with Arm |reg| TrustZone |reg|
 =============================================================================

 Applications on the nRF9160 may contain a Secure and a Non-Secure firmware
 image. The Secure image can be built using either Zephyr or
 `Trusted Firmware M`_ (TF-M). Non-Secure firmware images are always built
 using Zephyr. The two alternatives are described below.

 .. note::

    By default the Secure image for nRF9160 is built using TF-M.

 Building the Secure firmware using Zephyr
 -----------------------------------------

 The process requires the following steps:

 1. Build the Secure Zephyr application using ``-DBOARD=nrf9160dk_nrf9160`` and
    ``CONFIG_TRUSTED_EXECUTION_SECURE=y`` in the application project configuration file.
 2. Build the Non-Secure Zephyr application using ``-DBOARD=nrf9160dk_nrf9160_ns``.
 3. Merge the two binaries together.

 Building the Secure firmware with TF-M
 --------------------------------------

 The process to build the Secure firmware image using TF-M and the Non-Secure
 firmware image using Zephyr requires the following action:

 1. Build the Non-Secure Zephyr application
    using ``-DBOARD=nrf9160dk_nrf9160_ns``.
    To invoke the building of TF-M the Zephyr build system requires the
    Kconfig option ``BUILD_WITH_TFM`` to be enabled, which is done by
    default when building Zephyr as a Non-Secure application.
    The Zephyr build system will perform the following steps automatically:

       * Build the Non-Secure firmware image as a regular Zephyr application
       * Build a TF-M (secure) firmware image
       * Merge the output binaries together
       * Optionally build a bootloader image (MCUboot)

 .. note::

    Depending on the TF-M configuration, an application DTS overlay may be
    required, to adjust the Non-Secure image Flash and SRAM starting address
    and sizes.

 When building a Secure/Non-Secure application, the Secure application will
 have to set the IDAU (SPU) configuration to allow Non-Secure access to all
 CPU resources utilized by the Non-Secure application firmware. SPU
 configuration shall take place before jumping to the Non-Secure application.

 Building a Secure only application
 ==================================

 Build the Zephyr app in the usual way (see :ref:`build_an_application`
 and :ref:`application_run`), using ``-DBOARD=nrf9160dk_nrf9160``.


 Flashing
 ========

 Follow the instructions in the :ref:`nordic_segger` page to install
 and configure all the necessary software. Further information can be
 found in :ref:`nordic_segger_flashing`. Then build and flash
 applications as usual (see :ref:`build_an_application` and
 :ref:`application_run` for more details).

 Here is an example for the :ref:`hello_world` application.

 First, run your favorite terminal program to listen for output.

 .. code-block:: console

    $ minicom -D <tty_device> -b 115200

 Replace :code:`<tty_device>` with the port where the nRF9160 DK
 can be found. For example, under Linux, :code:`/dev/ttyACM0`.

 Then build and flash the application in the usual way.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: nrf9160dk_nrf9160
    :goals: build flash

 Debugging
 =========

 Refer to the :ref:`nordic_segger` page to learn about debugging Nordic boards with a
 Segger IC.


 Testing the LEDs and buttons in the nRF9160 DK
 **********************************************

 There are 2 samples that allow you to test that the buttons (switches) and LEDs on
 the board are working properly with Zephyr:

 * :ref:`blinky-sample`
 * :ref:`button-sample`

 You can build and flash the examples to make sure Zephyr is running correctly on
 your board. The button and LED definitions can be found in
 :zephyr_file:`boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160_common.dts`.

 References
 **********

 .. target-notes::

 .. _IDAU:
    https://developer.arm.com/docs/100690/latest/attribution-units-sau-and-idau
 .. _nRF9160 DK website: https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF9160-DK
 .. _Nordic Semiconductor Infocenter: https://infocenter.nordicsemi.com
 .. _Trusted Firmware M: https://www.trustedfirmware.org/projects/tf-m/
	.. _nrf9160dk_nrf9160:

	nRF9160 DK
	##########

	Overview
	********

	The nRF9160 DK (PCA10090) is a single-board development kit for evaluation and
	development on the nRF9160 SiP for LTE-M and NB-IoT. The nrf9160dk_nrf9160
	board configuration provides support for the Nordic Semiconductor nRF9160 ARM
	Cortex-M33F CPU with ARMv8-M Security Extension and the following devices:

	* :abbr:`ADC (Analog to Digital Converter)`
	* CLOCK
	* FLASH
	* :abbr:`GPIO (General Purpose Input Output)`
	* :abbr:`I2C (Inter-Integrated Circuit)`
	* :abbr:`MPU (Memory Protection Unit)`
	* :abbr:`NVIC (Nested Vectored Interrupt Controller)`
	* :abbr:`PWM (Pulse Width Modulation)`
	* :abbr:`RTC (nRF RTC System Clock)`
	* Segger RTT (RTT Console)
	* :abbr:`SPI (Serial Peripheral Interface)`
	* :abbr:`UARTE (Universal asynchronous receiver-transmitter with EasyDMA)`
	* :abbr:`WDT (Watchdog Timer)`
	* :abbr:`IDAU (Implementation Defined Attribution Unit)`

	.. figure:: img/nrf9160dk_nrf9160.jpg
	:align: center
	:alt: nRF9160 DK

	nRF9160 DK (Credit: Nordic Semiconductor)

	More information about the board can be found at the
	`nRF9160 DK website`_. The `Nordic Semiconductor Infocenter`_
	contains the processor's information and the datasheet.


	Hardware
	********

	nRF9160 DK has two external oscillators. The frequency of
	the slow clock is 32.768 kHz. The frequency of the main clock
	is 32 MHz.

	Supported Features
	==================

	The nrf9160dk_nrf9160 board configuration supports the following
	hardware features:

	+-----------+------------+----------------------+
	\| Interface \| Controller \| Driver/Component \|
	+===========+============+======================+
	\| ADC \| on-chip \| adc \|
	+-----------+------------+----------------------+
	\| CLOCK \| on-chip \| clock_control \|
	+-----------+------------+----------------------+
	\| FLASH \| on-chip \| flash \|
	+-----------+------------+----------------------+
	\| GPIO \| on-chip \| gpio \|
	+-----------+------------+----------------------+
	\| I2C(M) \| on-chip \| i2c \|
	+-----------+------------+----------------------+
	\| MPU \| on-chip \| arch/arm \|
	+-----------+------------+----------------------+
	\| NVIC \| on-chip \| arch/arm \|
	+-----------+------------+----------------------+
	\| PWM \| on-chip \| pwm \|
	+-----------+------------+----------------------+
	\| RTC \| on-chip \| system clock \|
	+-----------+------------+----------------------+
	\| RTT \| Segger \| console \|
	+-----------+------------+----------------------+
	\| SPI(M/S) \| on-chip \| spi \|
	+-----------+------------+----------------------+
	\| SPU \| on-chip \| system protection \|
	+-----------+------------+----------------------+
	\| UARTE \| on-chip \| serial \|
	+-----------+------------+----------------------+
	\| WDT \| on-chip \| watchdog \|
	+-----------+------------+----------------------+

	.. _nrf9160dk_additional_hardware:

	Additional hardware in v0.14.0+
	-------------------------------

	Starting from v0.14.0, additional hardware is available on the DK:

	* External flash memory (MX25R6435F, 64 Mb)
	* I/O expander (PCAL6408A) that can be used to interface LEDs, slide switches,
	and buttons

	To use this additional hardware, specify the revision of the board that
	should be used when building your application (for more information, see
	:ref:`application_board_version`). For example, to build for nRF9160 DK v1.0.0:

	.. zephyr-app-commands::
	:tool: all
	:cd-into:
	:board: nrf9160dk_nrf9160@1.0.0
	:goals: build
	:compact:

	Remember to also enable routing for this additional hardware in the firmware for
	:ref:`nrf9160dk_nrf52840` (see :ref:`nrf9160dk_board_controller_firmware`).

	Other hardware features have not been enabled yet for this board.
	See `nRF9160 DK website`_ and `Nordic Semiconductor Infocenter`_
	for a complete list of nRF9160 DK board hardware features.

	Connections and IOs
	===================

	LED
	---

	* LED1 (green) = P0.2
	* LED2 (green) = P0.3
	* LED3 (green) = P0.4
	* LED4 (green) = P0.5

	Push buttons and Switches
	-------------------------

	* BUTTON1 = P0.6
	* BUTTON2 = P0.7
	* SWITCH1 = P0.8
	* SWITCH2 = P0.9
	* BOOT = SW5 = boot/reset

	Security components
	===================

	- Implementation Defined Attribution Unit (`IDAU`_). The IDAU is implemented
	with the System Protection Unit and is used to define secure and non-secure
	memory maps. By default, all of the memory space (Flash, SRAM, and
	peripheral address space) is defined to be secure accessible only.
	- Secure boot.


	Programming and Debugging
	*************************

	nrf9160dk_nrf9160 supports the Armv8m Security Extension, and by default boots
	in the Secure state.

	Building Secure/Non-Secure Zephyr applications with Arm \|reg\| TrustZone \|reg\|
	=============================================================================

	Applications on the nRF9160 may contain a Secure and a Non-Secure firmware
	image. The Secure image can be built using either Zephyr or
	`Trusted Firmware M`_ (TF-M). Non-Secure firmware images are always built
	using Zephyr. The two alternatives are described below.

	.. note::

	By default the Secure image for nRF9160 is built using TF-M.

	Building the Secure firmware using Zephyr
	-----------------------------------------

	The process requires the following steps:

	1. Build the Secure Zephyr application using ``-DBOARD=nrf9160dk_nrf9160`` and
	``CONFIG_TRUSTED_EXECUTION_SECURE=y`` in the application project configuration file.
	2. Build the Non-Secure Zephyr application using ``-DBOARD=nrf9160dk_nrf9160_ns``.
	3. Merge the two binaries together.

	Building the Secure firmware with TF-M
	--------------------------------------

	The process to build the Secure firmware image using TF-M and the Non-Secure
	firmware image using Zephyr requires the following action:

	1. Build the Non-Secure Zephyr application
	using ``-DBOARD=nrf9160dk_nrf9160_ns``.
	To invoke the building of TF-M the Zephyr build system requires the
	Kconfig option ``BUILD_WITH_TFM`` to be enabled, which is done by
	default when building Zephyr as a Non-Secure application.
	The Zephyr build system will perform the following steps automatically:

	* Build the Non-Secure firmware image as a regular Zephyr application
	* Build a TF-M (secure) firmware image
	* Merge the output binaries together
	* Optionally build a bootloader image (MCUboot)

	.. note::

	Depending on the TF-M configuration, an application DTS overlay may be
	required, to adjust the Non-Secure image Flash and SRAM starting address
	and sizes.

	When building a Secure/Non-Secure application, the Secure application will
	have to set the IDAU (SPU) configuration to allow Non-Secure access to all
	CPU resources utilized by the Non-Secure application firmware. SPU
	configuration shall take place before jumping to the Non-Secure application.

	Building a Secure only application
	==================================

	Build the Zephyr app in the usual way (see :ref:`build_an_application`
	and :ref:`application_run`), using ``-DBOARD=nrf9160dk_nrf9160``.


	Flashing
	========

	Follow the instructions in the :ref:`nordic_segger` page to install
	and configure all the necessary software. Further information can be
	found in :ref:`nordic_segger_flashing`. Then build and flash
	applications as usual (see :ref:`build_an_application` and
	:ref:`application_run` for more details).

	Here is an example for the :ref:`hello_world` application.

	First, run your favorite terminal program to listen for output.

	.. code-block:: console

	$ minicom -D <tty_device> -b 115200

	Replace :code:`<tty_device>` with the port where the nRF9160 DK
	can be found. For example, under Linux, :code:`/dev/ttyACM0`.

	Then build and flash the application in the usual way.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: nrf9160dk_nrf9160
	:goals: build flash

	Debugging
	=========

	Refer to the :ref:`nordic_segger` page to learn about debugging Nordic boards with a
	Segger IC.


	Testing the LEDs and buttons in the nRF9160 DK
	**********************************************

	There are 2 samples that allow you to test that the buttons (switches) and LEDs on
	the board are working properly with Zephyr:

	* :ref:`blinky-sample`
	* :ref:`button-sample`

	You can build and flash the examples to make sure Zephyr is running correctly on
	your board. The button and LED definitions can be found in
	:zephyr_file:`boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160_common.dts`.

	References
	**********

	.. target-notes::

	.. _IDAU:
	https://developer.arm.com/docs/100690/latest/attribution-units-sau-and-idau
	.. _nRF9160 DK website: https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF9160-DK
	.. _Nordic Semiconductor Infocenter: https://infocenter.nordicsemi.com
	.. _Trusted Firmware M: https://www.trustedfirmware.org/projects/tf-m/