| # Private config options for txtime sample app |
| |
| # Copyright (c) 2020 Intel Corporation |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| mainmenu "Networking TXTIME sample application" |
| |
| config NET_SAMPLE_PEER |
| string "Peer IP address we are sending packets to" |
| help |
| The value depends on your network setup. This could be |
| a multicast address if needed. If port is not specified, |
| then 4242 is used. Currently the port value is only used |
| when selecting UDP socket type. |
| Syntax of the IP address string: |
| 192.0.2.1:80 |
| 192.0.2.42 |
| [2001:db8::1]:8080 |
| [2001:db8::2] |
| 2001:db::42 |
| |
| choice |
| prompt "Socket type to use" |
| help |
| Can be used to select whether the application will use UDP |
| socket to send data, or if it uses AF_PACKET (raw) socket. |
| |
| config NET_SAMPLE_UDP_SOCKET |
| bool "UDP socket" |
| help |
| Use UDP socket. |
| |
| config NET_SAMPLE_PACKET_SOCKET |
| bool "Packet socket" |
| select NET_SOCKETS_PACKET |
| help |
| Use AF_PACKET socket. Note that currently the application sends |
| dummy data that is not a valid Ethernet frame. We want to measure |
| how long it takes to send data so the actual data content is not |
| important for this sample application. |
| |
| endchoice |
| |
| config NET_SAMPLE_PACKET_INTERVAL |
| int "How long to wait between sent packets (in milliseconds)" |
| default 1000 |
| range 1 10000 |
| help |
| The application will send network packets between this |
| interval. The value is in milliseconds. |
| |
| config NET_SAMPLE_PACKET_TXTIME |
| int "What is the TXTIME (in microseconds)" |
| default 1000 |
| range 1 10000 |
| help |
| This tells what is the expected sending time of the network |
| packet by the network device driver. The value is in microseconds. |
| This value should be smaller than the interval time |
| (NET_SAMPLE_PACKET_INTERVAL). This value is added to current |
| time from PTP clock, to set the expected transmit time. Note that |
| the actual TXTIME given to Ethernet driver, is set in nanoseconds, |
| but for purpose of this sample application, we set the time in |
| microseconds in this config option. |
| |
| config NET_SAMPLE_IFACE2_MY_IPV6_ADDR |
| string "My IPv6 address for second interface" |
| help |
| The value depends on your network setup. |
| |
| config NET_SAMPLE_IFACE2_MY_IPV4_ADDR |
| string "My IPv4 address for second interface" |
| help |
| The value depends on your network setup. |
| |
| config NET_SAMPLE_IFACE2_VLAN_TAG |
| int "VLAN tag for second interface" |
| default 100 |
| range 0 4094 |
| depends on NET_VLAN |
| help |
| Set VLAN (virtual LAN) tag (id) that is used in the sample |
| application. |
| |
| config NET_SAMPLE_IFACE3_MY_IPV6_ADDR |
| string "My IPv6 address for third interface" |
| help |
| The value depends on your network setup. |
| |
| config NET_SAMPLE_IFACE3_MY_IPV4_ADDR |
| string "My IPv4 address for third interface" |
| help |
| The value depends on your network setup. |
| |
| config NET_SAMPLE_IFACE3_VLAN_TAG |
| int "VLAN tag for third interface" |
| default 200 |
| range 0 4094 |
| depends on NET_VLAN |
| help |
| Set VLAN (virtual LAN) tag (id) that is used in the sample |
| application. |
| |
| source "Kconfig.zephyr" |
