blob: 6121f440ba3f8560cfc1bac322f566de10492947 [file] [log] [blame]
/*
* Copyright (c) 2019 Derek Hageman <hageman@inthat.cloud>
*
* SPDX-License-Identifier: Apache-2.0
*/
#define DT_DRV_COMPAT atmel_sam0_eic
#include <zephyr/device.h>
#include <soc.h>
#include <zephyr/drivers/interrupt_controller/sam0_eic.h>
#include "intc_sam0_eic_priv.h"
struct sam0_eic_line_assignment {
uint8_t pin : 5;
uint8_t port : 2;
uint8_t enabled : 1;
};
struct sam0_eic_port_data {
sam0_eic_callback_t cb;
void *data;
};
struct sam0_eic_data {
struct sam0_eic_port_data ports[PORT_GROUPS];
struct sam0_eic_line_assignment lines[EIC_EXTINT_NUM];
};
static void wait_synchronization(void)
{
#ifdef REG_EIC_SYNCBUSY
while (EIC->SYNCBUSY.reg) {
}
#else
while (EIC->STATUS.bit.SYNCBUSY) {
}
#endif
}
static inline void set_eic_enable(bool on)
{
#ifdef REG_EIC_CTRLA
EIC->CTRLA.bit.ENABLE = on;
#else
EIC->CTRL.bit.ENABLE = on;
#endif
}
static void sam0_eic_isr(const struct device *dev)
{
struct sam0_eic_data *const dev_data = dev->data;
uint16_t bits = EIC->INTFLAG.reg;
uint32_t line_index;
/* Acknowledge all interrupts */
EIC->INTFLAG.reg = bits;
/* No clz on M0, so just do a quick test */
#if __CORTEX_M >= 3
line_index = __CLZ(__RBIT(bits));
bits >>= line_index;
#else
if (bits & 0xFF) {
line_index = 0;
} else {
line_index = 8;
bits >>= 8;
}
#endif
/*
* Map the EIC lines to the port pin masks based on which port is
* selected in the line data.
*/
for (; bits; bits >>= 1, line_index++) {
if (!(bits & 1)) {
continue;
}
/*
* These could be aggregated together into one call, but
* usually on a single one will be set, so just call them
* one by one.
*/
struct sam0_eic_line_assignment *line_assignment =
&dev_data->lines[line_index];
struct sam0_eic_port_data *port_data =
&dev_data->ports[line_assignment->port];
port_data->cb(BIT(line_assignment->pin), port_data->data);
}
}
int sam0_eic_acquire(int port, int pin, enum sam0_eic_trigger trigger,
bool filter, sam0_eic_callback_t cb, void *data)
{
const struct device *dev = DEVICE_DT_INST_GET(0);
struct sam0_eic_data *dev_data = dev->data;
struct sam0_eic_port_data *port_data;
struct sam0_eic_line_assignment *line_assignment;
uint32_t mask;
int line_index;
int config_index;
int config_shift;
unsigned int key;
uint32_t config;
line_index = sam0_eic_map_to_line(port, pin);
if (line_index < 0) {
return line_index;
}
mask = BIT(line_index);
config_index = line_index / 8;
config_shift = (line_index % 8) * 4;
/* Lock everything so it's safe to reconfigure */
key = irq_lock();
/* Disable the EIC for reconfiguration */
set_eic_enable(0);
line_assignment = &dev_data->lines[line_index];
/* Check that the required line is available */
if (line_assignment->enabled) {
if (line_assignment->port != port ||
line_assignment->pin != pin) {
goto err_in_use;
}
}
/* Set the EIC configuration data */
port_data = &dev_data->ports[port];
port_data->cb = cb;
port_data->data = data;
line_assignment->pin = pin;
line_assignment->port = port;
line_assignment->enabled = 1;
config = EIC->CONFIG[config_index].reg;
config &= ~(0xF << config_shift);
switch (trigger) {
case SAM0_EIC_RISING:
config |= EIC_CONFIG_SENSE0_RISE << config_shift;
break;
case SAM0_EIC_FALLING:
config |= EIC_CONFIG_SENSE0_FALL << config_shift;
break;
case SAM0_EIC_BOTH:
config |= EIC_CONFIG_SENSE0_BOTH << config_shift;
break;
case SAM0_EIC_HIGH:
config |= EIC_CONFIG_SENSE0_HIGH << config_shift;
break;
case SAM0_EIC_LOW:
config |= EIC_CONFIG_SENSE0_LOW << config_shift;
break;
}
if (filter) {
config |= EIC_CONFIG_FILTEN0 << config_shift;
}
/* Apply the config to the EIC itself */
EIC->CONFIG[config_index].reg = config;
set_eic_enable(1);
wait_synchronization();
/*
* Errata: The EIC generates a spurious interrupt for the newly
* enabled pin after being enabled, so clear it before re-enabling
* the IRQ.
*/
EIC->INTFLAG.reg = mask;
irq_unlock(key);
return 0;
err_in_use:
set_eic_enable(1);
wait_synchronization();
irq_unlock(key);
return -EBUSY;
}
static bool sam0_eic_check_ownership(int port, int pin, int line_index)
{
const struct device *dev = DEVICE_DT_INST_GET(0);
struct sam0_eic_data *dev_data = dev->data;
struct sam0_eic_line_assignment *line_assignment =
&dev_data->lines[line_index];
if (!line_assignment->enabled) {
return false;
}
if (line_assignment->port != port ||
line_assignment->pin != pin) {
return false;
}
return true;
}
int sam0_eic_release(int port, int pin)
{
const struct device *dev = DEVICE_DT_INST_GET(0);
struct sam0_eic_data *dev_data = dev->data;
uint32_t mask;
int line_index;
int config_index;
int config_shift;
unsigned int key;
line_index = sam0_eic_map_to_line(port, pin);
if (line_index < 0) {
return line_index;
}
mask = BIT(line_index);
config_index = line_index / 8;
config_shift = (line_index % 8) * 4;
/* Lock everything so it's safe to reconfigure */
key = irq_lock();
/* Disable the EIC */
set_eic_enable(0);
wait_synchronization();
/*
* Check to make sure the requesting actually owns the line and do
* nothing if it does not.
*/
if (!sam0_eic_check_ownership(port, pin, line_index)) {
goto done;
}
dev_data->lines[line_index].enabled = 0;
/* Clear the EIC config, including the trigger condition */
EIC->CONFIG[config_index].reg &= ~(0xF << config_shift);
/* Clear any pending interrupt for it */
EIC->INTENCLR.reg = mask;
EIC->INTFLAG.reg = mask;
done:
set_eic_enable(1);
wait_synchronization();
irq_unlock(key);
return 0;
}
int sam0_eic_enable_interrupt(int port, int pin)
{
uint32_t mask;
int line_index;
line_index = sam0_eic_map_to_line(port, pin);
if (line_index < 0) {
return line_index;
}
if (!sam0_eic_check_ownership(port, pin, line_index)) {
return -EBUSY;
}
mask = BIT(line_index);
EIC->INTFLAG.reg = mask;
EIC->INTENSET.reg = mask;
return 0;
}
int sam0_eic_disable_interrupt(int port, int pin)
{
uint32_t mask;
int line_index;
line_index = sam0_eic_map_to_line(port, pin);
if (line_index < 0) {
return line_index;
}
if (!sam0_eic_check_ownership(port, pin, line_index)) {
return -EBUSY;
}
mask = BIT(line_index);
EIC->INTENCLR.reg = mask;
EIC->INTFLAG.reg = mask;
return 0;
}
uint32_t sam0_eic_interrupt_pending(int port)
{
const struct device *dev = DEVICE_DT_INST_GET(0);
struct sam0_eic_data *dev_data = dev->data;
struct sam0_eic_line_assignment *line_assignment;
uint32_t set = EIC->INTFLAG.reg;
uint32_t mask = 0;
for (int line_index = 0; line_index < EIC_EXTINT_NUM; line_index++) {
line_assignment = &dev_data->lines[line_index];
if (!line_assignment->enabled) {
continue;
}
if (line_assignment->port != port) {
continue;
}
if (!(set & BIT(line_index))) {
continue;
}
mask |= BIT(line_assignment->pin);
}
return mask;
}
#define SAM0_EIC_IRQ_CONNECT(n) \
do { \
IRQ_CONNECT(DT_INST_IRQ_BY_IDX(0, n, irq), \
DT_INST_IRQ_BY_IDX(0, n, priority), \
sam0_eic_isr, DEVICE_DT_INST_GET(0), 0); \
irq_enable(DT_INST_IRQ_BY_IDX(0, n, irq)); \
} while (false)
static int sam0_eic_init(const struct device *dev)
{
ARG_UNUSED(dev);
#ifdef MCLK
/* Enable the EIC clock in APBAMASK */
MCLK->APBAMASK.reg |= MCLK_APBAMASK_EIC;
/* Enable the GCLK */
GCLK->PCHCTRL[EIC_GCLK_ID].reg = GCLK_PCHCTRL_GEN_GCLK0 |
GCLK_PCHCTRL_CHEN;
#else
/* Enable the EIC clock in PM */
PM->APBAMASK.bit.EIC_ = 1;
/* Enable the GCLK */
GCLK->CLKCTRL.reg = GCLK_CLKCTRL_ID_EIC | GCLK_CLKCTRL_GEN_GCLK0 |
GCLK_CLKCTRL_CLKEN;
#endif
#if DT_INST_IRQ_HAS_CELL(0, irq)
SAM0_EIC_IRQ_CONNECT(0);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 1)
SAM0_EIC_IRQ_CONNECT(1);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 2)
SAM0_EIC_IRQ_CONNECT(2);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 3)
SAM0_EIC_IRQ_CONNECT(3);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 4)
SAM0_EIC_IRQ_CONNECT(4);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 5)
SAM0_EIC_IRQ_CONNECT(5);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 6)
SAM0_EIC_IRQ_CONNECT(6);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 7)
SAM0_EIC_IRQ_CONNECT(7);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 8)
SAM0_EIC_IRQ_CONNECT(8);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 9)
SAM0_EIC_IRQ_CONNECT(9);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 10)
SAM0_EIC_IRQ_CONNECT(10);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 11)
SAM0_EIC_IRQ_CONNECT(11);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 12)
SAM0_EIC_IRQ_CONNECT(12);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 13)
SAM0_EIC_IRQ_CONNECT(13);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 14)
SAM0_EIC_IRQ_CONNECT(14);
#endif
#if DT_INST_IRQ_HAS_IDX(0, 15)
SAM0_EIC_IRQ_CONNECT(15);
#endif
set_eic_enable(1);
wait_synchronization();
return 0;
}
static struct sam0_eic_data eic_data;
DEVICE_DT_INST_DEFINE(0, sam0_eic_init,
NULL, &eic_data, NULL,
PRE_KERNEL_1, CONFIG_INTC_INIT_PRIORITY,
NULL);