| # Copyright 2020 Espressif Systems (Shanghai) PTE LTD |
| |
| menuconfig WIFI_ESP32 |
| bool "ESP32 SoC WiFi support" |
| default y |
| depends on DT_HAS_ESPRESSIF_ESP32_WIFI_ENABLED |
| depends on !SMP |
| select THREAD_CUSTOM_DATA |
| select NET_L2_WIFI_MGMT |
| select WIFI_USE_NATIVE_NETWORKING |
| select MBEDTLS |
| select MBEDTLS_ENTROPY_ENABLED |
| select MBEDTLS_KEY_EXCHANGE_ECDHE_ECDSA_ENABLED |
| select MBEDTLS_ECP_ALL_ENABLED |
| help |
| Enable ESP32 SoC WiFi support. Only supported in single |
| core mode because the network stack is not aware of SMP |
| stuff. |
| |
| if WIFI_ESP32 |
| |
| config ESP32_WIFI_SSID |
| string "SSID of WiFi network" |
| help |
| SSID (network name) for the application to connect to. |
| |
| config ESP32_WIFI_PASSWORD |
| string "Password (WPA or WPA2) of WiFi network" |
| help |
| WiFi password (WPA or WPA2) for the example to use. |
| |
| config ESP32_WIFI_STA_AUTO_DHCPV4 |
| bool "Automatically starts DHCP4 negotiation" |
| depends on NET_DHCPV4 |
| depends on NET_IPV4 |
| help |
| WiFi driver will automatically initiate DHCPV4 negotiation when connected. |
| |
| config ESP32_WIFI_STA_RECONNECT |
| bool "WiFi connection retry" |
| help |
| Set auto WiFI reconnection when disconnected. |
| |
| config ESP32_WIFI_EVENT_TASK_STACK_SIZE |
| int "Event Task Stack Size" |
| default 4096 |
| |
| config ESP32_WIFI_EVENT_TASK_PRIO |
| int "Event Task Priority" |
| default 4 |
| |
| config ESP32_WIFI_STATIC_RX_BUFFER_NUM |
| int "Max number of WiFi static RX buffers" |
| range 2 25 |
| default 10 |
| help |
| Set the number of WiFi static RX buffers. Each buffer takes approximately |
| 1.6KB of RAM. The static rx buffers are allocated when esp_wifi_init is |
| called, they are not freed until esp_wifi_deinit is called. |
| |
| WiFi hardware use these buffers to receive all 802.11 frames. A higher |
| number may allow higher throughput but increases memory use. |
| If ESP32_WIFI_AMPDU_RX_ENABLED is enabled, this value is recommended to |
| set equal or bigger than ESP32_WIFI_RX_BA_WIN in order to achieve better |
| throughput and compatibility with both stations and APs. |
| |
| config ESP32_WIFI_DYNAMIC_RX_BUFFER_NUM |
| int "Max number of WiFi dynamic RX buffers" |
| range 0 128 |
| default 32 |
| help |
| Set the number of WiFi dynamic RX buffers, 0 means unlimited RX buffers |
| will be allocated (provided sufficient free RAM). The size of each dynamic |
| RX buffer depends on the size of the received data frame. |
| |
| For each received data frame, the WiFi driver makes a copy to an RX buffer |
| and then delivers it to the high layer TCP/IP stack. The dynamic RX buffer |
| is freed after the higher layer has successfully received the data frame. |
| |
| For some applications, WiFi data frames may be received faster than the |
| application can process them. In these cases we may run out of memory if |
| RX buffer number is unlimited (0). If a dynamic RX buffer limit is set, |
| it should be at least the number of static RX buffers. |
| |
| choice ESP32_WIFI_TX_BUFFER |
| prompt "Type of WiFi TX buffers" |
| default ESP32_WIFI_DYNAMIC_TX_BUFFER |
| help |
| Select type of WiFi TX buffers: |
| |
| If "Static" is selected, WiFi TX buffers are allocated when WiFi is |
| initialized and released when WiFi is de-initialized. The size of each |
| static TX buffer is fixed to about 1.6KB. |
| |
| If "Dynamic" is selected, each WiFi TX buffer is allocated as needed |
| when a data frame is delivered to the Wifi driver from the TCP/IP stack. |
| The buffer is freed after the data frame has been sent by the WiFi driver. |
| The size of each dynamic TX buffer depends on the length of each data |
| frame sent by the TCP/IP layer. |
| |
| If PSRAM is enabled, "Static" should be selected to guarantee enough |
| WiFi TX buffers. If PSRAM is disabled, "Dynamic" should be selected |
| to improve the utilization of RAM. |
| |
| config ESP32_WIFI_STATIC_TX_BUFFER |
| bool "Static" |
| config ESP32_WIFI_DYNAMIC_TX_BUFFER |
| bool "Dynamic" |
| endchoice |
| |
| config ESP32_WIFI_TX_BUFFER_TYPE |
| int |
| default 0 if ESP32_WIFI_STATIC_TX_BUFFER |
| default 1 if ESP32_WIFI_DYNAMIC_TX_BUFFER |
| |
| config ESP32_WIFI_STATIC_TX_BUFFER_NUM |
| int "Max number of WiFi static TX buffers" |
| depends on ESP32_WIFI_STATIC_TX_BUFFER |
| range 1 64 |
| default 16 |
| help |
| Set the number of WiFi static TX buffers. Each buffer takes approximately |
| 1.6KB of RAM. The static RX buffers are allocated when esp_wifi_init() is |
| called, they are not released until esp_wifi_deinit() is called. |
| |
| For each transmitted data frame from the higher layer TCP/IP stack, |
| the WiFi driver makes a copy of it in a TX buffer. For some applications |
| especially UDP applications, the upper layer can deliver frames faster |
| than WiFi layer can transmit. |
| In these cases, we may run out of TX buffers. |
| |
| config ESP32_WIFI_CACHE_TX_BUFFER_NUM |
| int "Max number of WiFi cache TX buffers" |
| range 16 128 |
| default 32 |
| help |
| Set the number of WiFi cache TX buffer number. |
| |
| For each TX packet from uplayer, such as LWIP etc, WiFi driver needs to |
| allocate a static TX buffer and makes a copy of uplayer packet. If WiFi |
| driver fails to allocate the static TX buffer, it caches the uplayer |
| packets to a dedicated buffer queue, this option is used to configure the |
| size of the cached TX queue. |
| |
| config ESP32_WIFI_DYNAMIC_TX_BUFFER_NUM |
| int "Max number of WiFi dynamic TX buffers" |
| depends on ESP32_WIFI_DYNAMIC_TX_BUFFER |
| range 1 128 |
| default 32 |
| help |
| Set the number of WiFi dynamic TX buffers. The size of each |
| dynamic TXbuffer is not fixed, it depends on the size of each |
| transmitted data frame. |
| |
| For each transmitted frame from the higher layer TCP/IP stack, |
| the WiFi driver makes a copy of it in a TX buffer. For some applications, |
| especially UDP applications, the upper layer can deliver frames faster |
| than WiFi layer can transmit. In these cases, we may run out of TX |
| buffers. |
| |
| config ESP32_WIFI_CSI_ENABLED |
| bool "WiFi CSI(Channel State Information)" |
| help |
| Select this option to enable CSI(Channel State Information) feature. |
| CSI takes about CONFIG_ESP32_WIFI_STATIC_RX_BUFFER_NUM KB of RAM. |
| If CSI is not used, it is better to disable this feature in order |
| to save memory. |
| |
| config ESP32_WIFI_AMPDU_TX_ENABLED |
| bool "WiFi AMPDU TX" |
| default y |
| help |
| Select this option to enable AMPDU TX feature. It improves transmission |
| error checking and overall network performance with the cost of processing |
| speed. Helpful when the device is operating in crowded wireless area. |
| |
| config ESP32_WIFI_TX_BA_WIN |
| int "WiFi AMPDU TX BA window size" |
| depends on ESP32_WIFI_AMPDU_TX_ENABLED |
| range 2 32 |
| default 6 |
| help |
| Set the size of WiFi Block Ack TX window. Generally a bigger value means |
| higher throughput but more memory. Most of time we should NOT change the |
| default value unless special reason, e.g. test the maximum |
| UDP TX throughput with iperf etc. For iperf test in shieldbox, |
| the recommended value is 9~12. |
| |
| config ESP32_WIFI_AMPDU_RX_ENABLED |
| bool "WiFi AMPDU RX" |
| default y |
| help |
| Select this option to enable AMPDU RX feature. It improves transmission |
| error checking and overall network performance with the cost of processing |
| speed. Helpful when the device is operating in crowded wireless area. |
| |
| config ESP32_WIFI_RX_BA_WIN |
| int "WiFi AMPDU RX BA window size" |
| depends on ESP32_WIFI_AMPDU_RX_ENABLED |
| range 2 32 |
| default 6 |
| help |
| Set the size of WiFi Block Ack RX window. Generally a bigger value means |
| higher throughput and better compatibility but more memory. Most of time |
| we should NOT change the default value unless special reason, |
| e.g. test the maximum UDP RX throughput with iperf etc. For iperf test in |
| shieldbox, the recommended value is 9~12. If PSRAM is used and WiFi memory |
| is preferred to be allocated in PSRAM first, the default and minimum value |
| should be 16 to achieve better throughput and compatibility with both |
| stations and APs. |
| |
| choice ESP32_WIFI_TASK_CORE_ID |
| prompt "WiFi Task Core ID" |
| default ESP32_WIFI_TASK_PINNED_TO_CORE_0 |
| help |
| Pinned WiFi task to core 0 (core 1 not supported yet) |
| |
| config ESP32_WIFI_TASK_PINNED_TO_CORE_0 |
| bool "Core 0" |
| endchoice |
| |
| config ESP32_WIFI_SW_COEXIST_ENABLE |
| bool |
| help |
| Software controls WiFi/Bluetooth coexistence. Not supported yet. |
| |
| config ESP32_WIFI_IRAM_OPT |
| bool "WiFi IRAM speed optimization" |
| default y |
| help |
| Select this option to place frequently called Wi-Fi library functions in IRAM. |
| When this option is disabled, more than 10Kbytes of IRAM memory will be saved |
| but Wi-Fi throughput will be reduced. |
| |
| config ESP32_WIFI_RX_IRAM_OPT |
| bool "WiFi RX IRAM speed optimization" |
| default y |
| help |
| Select this option to place frequently called Wi-Fi library RX functions in IRAM. |
| When this option is disabled, more than 17Kbytes of IRAM memory will be saved |
| but Wi-Fi performance will be reduced. |
| |
| config ESP32_WIFI_NET_ALLOC_SPIRAM |
| bool "Allocate memory of WiFi and NET in SPIRAM" |
| depends on ESP_SPIRAM |
| help |
| Allocate memory of WiFi and NET stack in SPIRAM, increasing available RAM memory space |
| for application stack. |
| |
| endif # WIFI_ESP32 |
