| # |
| # Copyright (c) 2014 Wind River Systems, Inc. |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| if SOC_QUARK_SE_SS |
| |
| config SOC |
| default quark_se_ss |
| |
| config NUM_IRQ_PRIO_LEVELS |
| # This processor supports only 2 priority levels: |
| # 0 for Fast Interrupts (FIRQs) and 1 for Regular Interrupts (IRQs). |
| default 2 |
| |
| config NUM_REGULAR_IRQ_PRIO_LEVELS |
| # This processor supports only 1 Regular Interrupt priority level (1). |
| default 1 |
| |
| config NUM_IRQS |
| # must be > the highest interrupt number used |
| default 68 |
| |
| |
| config SYS_CLOCK_HW_CYCLES_PER_SEC |
| default 32000000 |
| |
| config RAM_START |
| default 0x4000 if NSIM |
| default 0xa8000400 |
| |
| config RAM_SIZE |
| default 16 if NSIM |
| default 24 |
| |
| if GPIO |
| config GPIO_DW |
| def_bool y |
| config GPIO_DW_BOTHEDGES_SUPPORT |
| default n |
| |
| config GPIO_DW_0 |
| def_bool y |
| config GPIO_DW_0_BASE_ADDR |
| default 0x80017800 |
| config GPIO_DW_0_IRQ |
| default 20 |
| config GPIO_DW_0_BITS |
| default 8 |
| |
| config GPIO_DW_1 |
| def_bool y |
| config GPIO_DW_1_BASE_ADDR |
| default 0x80017900 |
| config GPIO_DW_1_IRQ |
| default 21 |
| config GPIO_DW_1_BITS |
| default 8 |
| endif |
| |
| if I2C |
| |
| config I2C_QUARK_SE_SS |
| def_bool y |
| |
| config I2C_QUARK_SE_SS_0 |
| def_bool y |
| |
| if I2C_QUARK_SE_SS_0 |
| |
| config I2C_QUARK_SE_SS_0_BASE |
| default 0x80012000 |
| |
| config I2C_QUARK_SE_SS_0_NAME |
| default "I2C0" |
| |
| config I2C_QUARK_SE_SS_0_DEFAULT_CFG |
| default 0x12 |
| |
| endif |
| |
| if I2C_QUARK_SE_SS_1 |
| |
| config I2C_QUARK_SE_SS_1_BASE |
| default 0x80012100 |
| |
| config I2C_QUARK_SE_SS_1_NAME |
| default "I2C1" |
| |
| config I2C_QUARK_SE_SS_1_DEFAULT_CFG |
| default 0x12 |
| |
| endif |
| |
| endif # I2C |
| |
| if UART_NS16550 |
| |
| config UART_NS16550_PORT_0 |
| def_bool y |
| |
| if UART_NS16550_PORT_0 |
| |
| config UART_NS16550_PORT_0_NAME |
| default "UART_0" |
| config UART_NS16550_PORT_0_BASE_ADDR |
| default 0xB0002000 |
| config UART_NS16550_PORT_0_IRQ |
| default 41 |
| config UART_NS16550_PORT_0_IRQ_PRI |
| default 1 |
| config UART_NS16550_PORT_0_BAUD_RATE |
| default 115200 |
| config UART_NS16550_PORT_0_CLK_FREQ |
| default 32000000 |
| config UART_NS16550_PORT_0_OPTIONS |
| default 0 |
| |
| endif # UART_NS16550_PORT_0 |
| |
| config UART_NS16550_PORT_1 |
| def_bool y |
| |
| if UART_NS16550_PORT_1 |
| |
| config UART_NS16550_PORT_1_NAME |
| default "UART_1" |
| config UART_NS16550_PORT_1_BASE_ADDR |
| default 0xB0002400 |
| config UART_NS16550_PORT_1_IRQ |
| default 42 |
| config UART_NS16550_PORT_1_IRQ_PRI |
| default 1 |
| config UART_NS16550_PORT_1_BAUD_RATE |
| default 115200 |
| config UART_NS16550_PORT_1_CLK_FREQ |
| default 32000000 |
| config UART_NS16550_PORT_1_OPTIONS |
| default 0 |
| |
| endif # UART_NS16550_PORT_1 |
| |
| endif # UART_NS16550 |
| |
| if UART_CONSOLE |
| |
| config UART_CONSOLE_ON_DEV_NAME |
| default "UART_1" |
| config UART_CONSOLE_IRQ |
| default 42 |
| config UART_CONSOLE_IRQ_PRI |
| default 1 |
| |
| endif |
| |
| config KERNEL_INIT_PRIORITY_DEFAULT |
| default 40 |
| |
| config KERNEL_INIT_PRIORITY_DEVICE |
| default 50 |
| |
| config IPM_CONSOLE_PRIORITY |
| default 60 |
| |
| config UART_CONSOLE_PRIORITY |
| default 60 |
| |
| config GPIO_DW_INIT_PRIORITY |
| default 60 |
| |
| config I2C_INIT_PRIORITY |
| default 60 |
| |
| endif #SOC_QUARK_SE_ARC |