blob: 27d9aaaf861d46479e1ef8a9bf98421a25b2c2a7 [file] [log] [blame]
.. _msp_exp432p401r_launchxl:
MSP-EXP432P401R LaunchXL
########################
Overview
********
The SimpleLink MSPEXP432P401R LaunchPad development kit is an easy-to-use evaluation
module for the SimpleLink MSP432P401R microcontroller. It contains everything needed to start
developing on the SimpleLink MSP432 low-power + performance ARM |reg| 32-bit Cortex |reg|-M4F
microcontroller (MCU).
.. figure:: img/msp_exp432p401r_launchxl.jpg
:align: center
:alt: MSP-EXP432P401R LaunchXL development board
Features:
=========
* Low-power ARM Cortex-M4F MSP432P401R
* 40-pin LaunchPad development kit standard that leverages the BoosterPack plug-in module ecosystem
* XDS110-ET, an open-source onboard debug probe featuring EnergyTrace+ technology and application
UART
* Two buttons and two LEDs for user interaction
* Backchannel UART through USB to PC
Details on the MSP-EXP432P401R LaunchXL development board can be found in the
`MSP-EXP432P401R LaunchXL User's Guide`_.
Supported Features
==================
* The on-board 32-kHz crystal allows for lower LPM3 sleep currents and a higher-precision clock source than the
default internal 32-kHz REFOCLK. Therefore, the presence of the crystal allows the full range of low-
power modes to be used.
* The on-board 48-MHz crystal allows the device to run at its maximum operating speed for MCLK and HSMCLK.
The MSP-EXP432P401R LaunchXL development board configuration supports the following hardware features:
+-----------+------------+-----------------------+
| Interface | Controller | Driver/Component |
+===========+============+=======================+
| NVIC | on-chip | nested vectored |
| | | interrupt controller |
+-----------+------------+-----------------------+
| SYSTICK | on-chip | system clock |
+-----------+------------+-----------------------+
| UART | on-chip | serial port |
+-----------+------------+-----------------------+
More details about the supported peripherals are available in `MSP432P4XX TRM`_
Other hardware features are not currently supported by the Zephyr kernel.
Building and Flashing
*********************
Building
========
Follow the :ref:`getting_started` instructions for Zephyr application
development.
For example, to build the :ref:`hello_world` application for the
MSP-EXP432P401R LaunchXL:
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: msp_exp432p401r_launchxl
:goals: build
The resulting ``zephyr.elf`` binary in the build directory can be flashed onto
MSP-EXP432P401R LaunchXL using the command line utility mentioned below.
Flashing
========
For Linux:
----------
`UniFlash`_ command line utility is used to program the flash memory. Only
elf loading is currently supported.
The following command will flash the ``zephyr.elf`` binary to the MSP-EXP432P401R LaunchXL board:
.. code-block:: console
$ ./dslite.sh --config=MSP432P401R.ccxml zephyr.elf
.. note:: The ccxml configuration file is included in boards/arm/msp_exp432p401r_launchxl/support.
Debugging
=========
MSP-EXP432P401R LaunchXL board supports debugging primarily using `CCS IDE`_. More information
on debugging using CCS can be found in `CCS Debug Handbook`_.
Launchpad also supports debugging using GDB. See section 3.3 of `GCC ARM Toolchain Guide`_.
References
**********
TI MSP432 Wiki:
https://en.wikipedia.org/wiki/TI_MSP432
TI MSP432P401R Product Page:
http://www.ti.com/product/msp432p401r
TI MSP432 SDK:
http://www.ti.com/tool/SIMPLELINK-MSP432-SDK
.. _MSP-EXP432P401R LaunchXL User's Guide:
http://www.ti.com/lit/ug/slau597c/slau597c.pdf
.. _MSP432P4XX TRM:
http://www.ti.com/lit/ug/slau356f/slau356f.pdf
.. _UniFlash:
http://processors.wiki.ti.com/index.php/UniFlash_v4_Quick_Guide#Command_Line_Interface
.. _CCS IDE:
http://www.ti.com/tool/ccstudio
.. _CCS Debug Handbook:
http://processors.wiki.ti.com/index.php/Debug_Handbook_for_CCS#Cortex_M3.2FM4.2FTiva.2FMSP432
.. _GCC ARM Toolchain Guide:
http://www.ti.com/lit/ug/slau688b/slau688b.pdf