| .. _nrf52dk_nrf52832: |
| |
| nRF52 DK |
| ######## |
| |
| Overview |
| ******** |
| |
| The nRF52 Development Kit (PCA10040) hardware provides |
| support for the Nordic Semiconductor nRF52832 ARM Cortex-M4F CPU and |
| the following devices: |
| |
| * :abbr:`ADC (Analog to Digital Converter)` |
| * CLOCK |
| * FLASH |
| * :abbr:`GPIO (General Purpose Input Output)` |
| * :abbr:`I2C (Inter-Integrated Circuit)` |
| * :abbr:`MPU (Memory Protection Unit)` |
| * :abbr:`NVIC (Nested Vectored Interrupt Controller)` |
| * :abbr:`PWM (Pulse Width Modulation)` |
| * RADIO (Bluetooth Low Energy) |
| * :abbr:`RTC (nRF RTC System Clock)` |
| * Segger RTT (RTT Console) |
| * :abbr:`SPI (Serial Peripheral Interface)` |
| * :abbr:`UART (Universal asynchronous receiver-transmitter)` |
| * :abbr:`WDT (Watchdog Timer)` |
| |
| .. figure:: img/nrf52dk_nrf52832.jpg |
| :width: 442px |
| :align: center |
| :alt: nRF52 DK |
| |
| nRF52 DK (Credit: Nordic Semiconductor) |
| |
| More information about the board can be found at the |
| `nRF52 DK website`_. The `Nordic Semiconductor Infocenter`_ |
| contains the processor's information and the datasheet. |
| |
| |
| Hardware |
| ******** |
| |
| nRF52 DK has two external oscillators. The frequency of |
| the slow clock is 32.768 kHz. The frequency of the main clock |
| is 32 MHz. |
| |
| Supported Features |
| ================== |
| |
| The nrf52dk_nrf52832 board configuration supports the following |
| hardware features: |
| |
| +-----------+------------+----------------------+ |
| | Interface | Controller | Driver/Component | |
| +===========+============+======================+ |
| | ADC | on-chip | adc | |
| +-----------+------------+----------------------+ |
| | CLOCK | on-chip | clock_control | |
| +-----------+------------+----------------------+ |
| | FLASH | on-chip | flash | |
| +-----------+------------+----------------------+ |
| | GPIO | on-chip | gpio | |
| +-----------+------------+----------------------+ |
| | I2C(M) | on-chip | i2c | |
| +-----------+------------+----------------------+ |
| | MPU | on-chip | arch/arm | |
| +-----------+------------+----------------------+ |
| | NVIC | on-chip | arch/arm | |
| +-----------+------------+----------------------+ |
| | PWM | on-chip | pwm | |
| +-----------+------------+----------------------+ |
| | RADIO | on-chip | Bluetooth | |
| +-----------+------------+----------------------+ |
| | RTC | on-chip | system clock | |
| +-----------+------------+----------------------+ |
| | RTT | Segger | console | |
| +-----------+------------+----------------------+ |
| | SPI(M/S) | on-chip | spi | |
| +-----------+------------+----------------------+ |
| | UART | on-chip | serial | |
| +-----------+------------+----------------------+ |
| | WDT | on-chip | watchdog | |
| +-----------+------------+----------------------+ |
| |
| Other hardware features have not been enabled yet for this board. |
| See `nRF52 DK website`_ and `Nordic Semiconductor Infocenter`_ |
| for a complete list of nRF52 Development Kit board hardware features. |
| |
| Connections and IOs |
| =================== |
| |
| LED |
| --- |
| |
| * LED1 (green) = P0.17 |
| * LED2 (green) = P0.18 |
| * LED3 (green) = P0.19 |
| * LED4 (green) = P0.20 |
| * LD5 (red/green) = OB LED 1/2 |
| |
| Push buttons |
| ------------ |
| |
| * BUTTON1 = SW1 = P0.13 |
| * BUTTON2 = SW2 = P0.14 |
| * BUTTON3 = SW3 = P0.15 |
| * BUTTON4 = SW4 = P0.16 |
| * BOOT = SW5 = boot/reset |
| |
| External Connectors |
| ------------------- |
| |
| J-Link Prog Connector |
| |
| +-------+--------------+ |
| | PIN # | Signal Name | |
| +=======+==============+ |
| | 1 | VDD | |
| +-------+--------------+ |
| | 2 | IMCU_TMSS | |
| +-------+--------------+ |
| | 3 | GND | |
| +-------+--------------+ |
| | 4 | IMCU_TCKS | |
| +-------+--------------+ |
| | 5 | V5V | |
| +-------+--------------+ |
| | 6 | IMCU_TDOS | |
| +-------+--------------+ |
| | 7 | Cut off | |
| +-------+--------------+ |
| | 8 | IMCU_TDIS | |
| +-------+--------------+ |
| | 9 | Cut off | |
| +-------+--------------+ |
| | 10 | IMCU_RESET | |
| +-------+--------------+ |
| |
| Debug IN |
| |
| +-------+--------------+-------------------------+ |
| | PIN # | Signal Name | NRF52832 Functions | |
| +=======+==============+=========================+ |
| | 1 | VDD | N/A | |
| +-------+--------------+-------------------------+ |
| | 2 | SWDIO | SWDIO | |
| +-------+--------------+-------------------------+ |
| | 3 | GND | N/A | |
| +-------+--------------+-------------------------+ |
| | 4 | SWDCLK | SWDCLK | |
| +-------+--------------+-------------------------+ |
| | 5 | GND | N/A | |
| +-------+--------------+-------------------------+ |
| | 6 | P0.18 | P0.18 / TRACEDATA[0] / | |
| | | | SWO | |
| +-------+--------------+-------------------------+ |
| | 7 | Cut off | N/A | |
| +-------+--------------+-------------------------+ |
| | 8 | Cut off | N/A | |
| +-------+--------------+-------------------------+ |
| | 9 | GND | N/A | |
| +-------+--------------+-------------------------+ |
| | 10 | P0.21 | P0.21 / RESET | |
| +-------+--------------+-------------------------+ |
| |
| Debug OUT |
| |
| +-------+----------------+ |
| | PIN # | Signal Name | |
| +=======+================+ |
| | 1 | EXT_VTG | |
| +-------+----------------+ |
| | 2 | EXT_SWDIO | |
| +-------+----------------+ |
| | 3 | GND | |
| +-------+----------------+ |
| | 4 | EXT_SWDCLK | |
| +-------+----------------+ |
| | 5 | GND | |
| +-------+----------------+ |
| | 6 | EXT_SWO | |
| | | | |
| +-------+----------------+ |
| | 7 | Cut off | |
| +-------+----------------+ |
| | 8 | Cut off | |
| +-------+----------------+ |
| | 9 | EXT_GND_DETECT | |
| +-------+----------------+ |
| | 10 | EXT_RESET | |
| +-------+----------------+ |
| |
| Shield Debug and Current measurement |
| |
| +-------+----------------+ |
| | PIN # | Signal Name | |
| +=======+================+ |
| | 1 | VDD_nRF | |
| +-------+----------------+ |
| | 2 | VDD | |
| +-------+----------------+ |
| | 3 | SH_VTG | |
| +-------+----------------+ |
| | 4 | SH_SWDIO | |
| +-------+----------------+ |
| | 5 | SH_SWDCLK | |
| +-------+----------------+ |
| | 6 | SH_SWO | |
| +-------+----------------+ |
| | 7 | SH_RESET | |
| +-------+----------------+ |
| | 8 | SH_GND_DETECT | |
| +-------+----------------+ |
| |
| Auxiliary |
| |
| +-------+--------------+-------------------------+ |
| | PIN # | Signal Name | NRF52832 Functions | |
| +=======+==============+=========================+ |
| | 1 | P0.00 | P0.00 / XL1 | |
| +-------+--------------+-------------------------+ |
| | 2 | P0.01 | P0.01 / XL2 | |
| +-------+--------------+-------------------------+ |
| | 3 | P0.21 | P0.21 / RESET | |
| +-------+--------------+-------------------------+ |
| | 4 | P0.05_C | P0.05 / AIN3 | |
| +-------+--------------+-------------------------+ |
| | 5 | P0.06_C | P0.06 | |
| +-------+--------------+-------------------------+ |
| | 6 | P0.07_C | P0.07 | |
| +-------+--------------+-------------------------+ |
| | 7 | P0.08_C | P0.08 | |
| +-------+--------------+-------------------------+ |
| | 8 | P0.09 | P0.09 / NFC1 | |
| +-------+--------------+-------------------------+ |
| | 9 | P0.10 | P0.10 / NFC2 | |
| +-------+--------------+-------------------------+ |
| |
| Arduino Headers |
| --------------- |
| |
| P1/P7 Power |
| |
| +-------+--------------+-------------------------+ |
| | PIN # | Signal Name | NRF52832 Functions | |
| +=======+==============+=========================+ |
| | 1 | VDD | N/A | |
| +-------+--------------+-------------------------+ |
| | 2 | VDD | N/A | |
| +-------+--------------+-------------------------+ |
| | 3 | RESET | P0.21 / RESET | |
| +-------+--------------+-------------------------+ |
| | 4 | VDD | N/A | |
| +-------+--------------+-------------------------+ |
| | 5 | V5V | N/A | |
| +-------+--------------+-------------------------+ |
| | 6 | GND | N/A | |
| +-------+--------------+-------------------------+ |
| | 7 | GND | N/A | |
| +-------+--------------+-------------------------+ |
| | 8 | VIN | N/A | |
| +-------+--------------+-------------------------+ |
| |
| P2/P8 Analog in |
| |
| +-------+--------------+-------------------------+ |
| | PIN # | Signal Name | NRF52832 Functions | |
| +=======+==============+=========================+ |
| | 1 | A0 | P0.03 / AIN1 | |
| +-------+--------------+-------------------------+ |
| | 2 | A1 | P0.04 / AIN2 | |
| +-------+--------------+-------------------------+ |
| | 3 | A2 | P0.28 / AIN4 | |
| +-------+--------------+-------------------------+ |
| | 4 | A3 | P0.29 / AIN5 | |
| +-------+--------------+-------------------------+ |
| | 5 | A4 | P0.30 / AIN6 | |
| +-------+--------------+-------------------------+ |
| | 6 | A5 | P0.31 / AIN7 | |
| +-------+--------------+-------------------------+ |
| |
| P3/P9 Digital I/O |
| |
| +-------+--------------+-------------------------+ |
| | PIN # | Signal Name | NRF52832 Functions | |
| +=======+==============+=========================+ |
| | 1 | D0 (RX) | P0.11 | |
| +-------+--------------+-------------------------+ |
| | 2 | D1 (TX) | P0.12 | |
| +-------+--------------+-------------------------+ |
| | 3 | D2 | P0.13 | |
| +-------+--------------+-------------------------+ |
| | 4 | D3 | P0.14 / TRACEDATA[3] | |
| +-------+--------------+-------------------------+ |
| | 5 | D4 | P0.15 / TRACEDATA[2] | |
| +-------+--------------+-------------------------+ |
| | 6 | D5 | P0.16 / TRACEDATA[1] | |
| +-------+--------------+-------------------------+ |
| | 7 | D6 | P0.17 | |
| +-------+--------------+-------------------------+ |
| | 8 | D7 | P0.18 / TRACEDATA[3] / | |
| | | | SWO | |
| +-------+--------------+-------------------------+ |
| |
| P4/P10 Digital I/O |
| |
| +-------+--------------+-------------------------+ |
| | PIN # | Signal Name | NRF52832 Functions | |
| +=======+==============+=========================+ |
| | 1 | D8 | P0.19 | |
| +-------+--------------+-------------------------+ |
| | 2 | D9 | P0.20 / TRACECLK | |
| +-------+--------------+-------------------------+ |
| | 3 | D10 (SS) | P0.22 | |
| +-------+--------------+-------------------------+ |
| | 4 | D11 (MOSI) | P0.23 | |
| +-------+--------------+-------------------------+ |
| | 5 | D12 (MISO) | P0.24 | |
| +-------+--------------+-------------------------+ |
| | 6 | D13 (SCK) | P0.25 | |
| +-------+--------------+-------------------------+ |
| | 7 | GND | N/A | |
| +-------+--------------+-------------------------+ |
| | 8 | AREF | P0.02 / AIN0 | |
| +-------+--------------+-------------------------+ |
| | 9 | SDA | P0.26 | |
| +-------+--------------+-------------------------+ |
| | 10 | SCL | P0.27 | |
| +-------+--------------+-------------------------+ |
| |
| P5/P11 |
| |
| +-------+--------------+-------------------------+ |
| | PIN # | Signal Name | NRF52832 Functions | |
| +=======+==============+=========================+ |
| | 1 | D12 (MISO) | P0.24 | |
| +-------+--------------+-------------------------+ |
| | 2 | V5V | N/A | |
| +-------+--------------+-------------------------+ |
| | 3 | D13 (SCK) | P0.25 | |
| +-------+--------------+-------------------------+ |
| | 4 | D11 (MOSI) | P0.23 | |
| +-------+--------------+-------------------------+ |
| | 5 | RESET | N/A | |
| +-------+--------------+-------------------------+ |
| | 6 | N/A | N/A | |
| +-------+--------------+-------------------------+ |
| |
| Programming and Debugging |
| ************************* |
| |
| Flashing |
| ======== |
| |
| Follow the instructions in the :ref:`nordic_segger` page to install |
| and configure all the necessary software. Further information can be |
| found in :ref:`nordic_segger_flashing`. Then build and flash |
| applications as usual (see :ref:`build_an_application` and |
| :ref:`application_run` for more details). |
| |
| Here is an example for the :ref:`hello_world` application. |
| |
| First, run your favorite terminal program to listen for output. |
| |
| .. code-block:: console |
| |
| $ minicom -D <tty_device> -b 115200 |
| |
| Replace :code:`<tty_device>` with the port where the board nRF52 DK |
| can be found. For example, under Linux, :code:`/dev/ttyACM0`. |
| |
| Then build and flash the application in the usual way. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: nrf52dk_nrf52832 |
| :goals: build flash |
| |
| Debugging |
| ========= |
| |
| Refer to the :ref:`nordic_segger` page to learn about debugging Nordic boards with a |
| Segger IC. |
| |
| |
| Testing the LEDs and buttons in the nRF52 DK |
| ******************************************** |
| |
| There are 2 samples that allow you to test that the buttons (switches) and LEDs on |
| the board are working properly with Zephyr: |
| |
| .. code-block:: console |
| |
| samples/basic/blinky |
| samples/basic/button |
| |
| You can build and flash the examples to make sure Zephyr is running correctly on |
| your board. The button and LED definitions can be found in |
| :zephyr_file:`boards/arm/nrf52dk_nrf52832/nrf52dk_nrf52832.dts`. |
| |
| References |
| ********** |
| |
| .. target-notes:: |
| |
| .. _nRF52 DK website: https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52-DK |
| .. _Nordic Semiconductor Infocenter: https://infocenter.nordicsemi.com |
