blob: d7ac4f59115c7901f0c872062f0842893fa77f5b [file] [log] [blame]
# Bluetooth drivers configuration options
# Copyright (c) 2016 Intel Corporation
# SPDX-License-Identifier: Apache-2.0
comment "Bluetooth HCI Driver Options"
config BT_UART
bool
choice BT_HCI_BUS_TYPE
prompt "Bluetooth HCI driver"
config BT_H4
bool "H:4 UART"
select UART_INTERRUPT_DRIVEN
select BT_UART
depends on SERIAL
help
Bluetooth H:4 UART driver. Requires hardware flow control
lines to be available.
config BT_H5
bool "H:5 UART [EXPERIMENTAL]"
select UART_INTERRUPT_DRIVEN
select BT_UART
select EXPERIMENTAL
depends on SERIAL
help
Bluetooth three-wire (H:5) UART driver. Implementation of HCI
Three-Wire UART Transport Layer.
config BT_RPMSG
bool "HCI using RPMsg"
select BT_HAS_HCI_VS
select IPC_SERVICE
select MBOX
help
Bluetooth HCI driver for communication with another CPU
using RPMsg framework.
config BT_SPI
bool "SPI HCI"
depends on SPI
help
Supports Bluetooth ICs using SPI as the communication protocol.
HCI packets are sent and received as single Byte transfers,
prepended after a known header. Headers may vary per device, so
additional platform specific knowledge may need to be added as
devices are.
config BT_STM32_IPM
bool "IPM HCI"
select USE_STM32_HAL_CORTEX
select HAS_STM32LIB
help
TODO
config BT_SILABS_HCI
bool "Silicon Labs Bluetooth interface"
depends on SOC_SERIES_EFR32BG22 || SOC_SERIES_EFR32MG24 || SOC_SERIES_EFR32BG27
depends on !PM || SOC_GECKO_PM_BACKEND_PMGR
select ENTROPY_GENERATOR
select MBEDTLS
select MBEDTLS_PSA_CRYPTO_C
select MBEDTLS_ENTROPY_ENABLED
select MBEDTLS_ZEPHYR_ENTROPY
help
Use Silicon Labs binary Bluetooth library to connect to the
controller.
config BT_USERCHAN
bool "HCI User Channel based driver"
depends on BOARD_NATIVE_POSIX
help
This driver provides access to the local Linux host's Bluetooth
adapter using a User Channel HCI socket to the Linux kernel. It
is only intended to be used with the native POSIX build of Zephyr.
The Bluetooth adapter must be powered off in order for Zephyr to
be able to use it.
config BT_ESP32
bool "ESP32 HCI driver"
help
Espressif HCI bluetooth interface
config BT_B91
bool "Telink B91 HCI driver"
help
Telink B91 HCI bluetooth interface
config BT_PSOC6_BLESS
bool "PSOC6 BLESS driver"
select BT_HCI_SETUP
help
PSOC6 BLESS driver with BLE Controller which operates in
Single CPU mode.
config BT_NO_DRIVER
bool "No default HCI driver"
help
This is intended for unit tests where no internal driver
should be selected.
endchoice
if BT_SPI
config BT_SPI_INIT_PRIORITY
int "BT SPI init priority"
default 75
config BT_BLUENRG_ACI
bool "ACI message with with BlueNRG-based devices"
help
Enable support for devices compatible with the BlueNRG Bluetooth
Stack. Current driver supports: ST BLUENRG-MS.
config BT_SPI_BLUENRG
bool "Compatibility with BlueNRG-based devices"
help
Enable support for devices compatible with the BlueNRG Bluetooth
Stack. Current driver supports: ST BLUENRG-MS.
endif # BT_SPI
config BT_STM32_IPM_RX_STACK_SIZE
int "STM32 IPM stack size for RX thread"
depends on BT_STM32_IPM
default 512
menuconfig BT_CYW43XXX
bool "CYW43XXX BT connectivity"
default y
select BT_HCI_SETUP
depends on GPIO
depends on DT_HAS_INFINEON_CYW43XXX_BT_HCI_ENABLED
depends on BT_H4
help
Infineon's AIROC Wi-Fi & combos portfolio integrates
IEEE 802.11a/b/g/n/ac/ax Wi-Fi and Bluetooth® 5.2 in a single-chip
solution to enable small-form-factor IoT designs.
source "drivers/bluetooth/hci/Kconfig.infineon"
config BT_DRIVER_QUIRK_NO_AUTO_DLE
bool "Host auto-initiated Data Length Update quirk"
depends on BT_AUTO_DATA_LEN_UPDATE
default y if BT_RPMSG || BT_ESP32
help
Enable the quirk wherein BT Host stack will auto-initiate Data Length
Update procedure for new connections for controllers that do not
auto-initiate the procedure if the default data length parameters are
not equal to the initial parameters.
This has to be enabled when the BLE controller connected is Zephyr
open source controller.
config BT_HCI_SETUP
bool
help
Enable the HCI vendor-specific Setup function.
This option has to be enabled when the BT Controller requires execution
of the vendor-specific commands sequence to initialize the BT Controller
before the BT Host executes a Reset sequence.
The user should generally avoid changing it via menuconfig or in
configuration files. This option are enabled by the vendor-specific
HCI extension, where the Setup function is implemented.
config BT_DRV_TX_STACK_SIZE
int
default 256
help
Stack size for the HCI driver's TX thread.
config BT_DRV_RX_STACK_SIZE
int
default 512 if BT_SPI
default BT_RX_STACK_SIZE if (BT_H4 || BT_HCI_RAW_H4)
default BT_STM32_IPM_RX_STACK_SIZE if BT_STM32_IPM
default 256
help
Stack size for the HCI driver's RX thread.
config BT_SILABS_HCI_BUFFER_MEMORY
int "Silicon Labs Bluetooth Library memory buffer size"
depends on BT_SILABS_HCI
default 6144
help
Select the size of allocated memory buffer for the Silicon Labs
Bluetooth Library.