| # Copyright (c) 2021 Espressif Systems (Shanghai) Co., Ltd. |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| config SOC_ESP32S2 |
| bool "ESP32S2" |
| select XTENSA |
| select ATOMIC_OPERATIONS_C |
| select DYNAMIC_INTERRUPTS |
| select CLOCK_CONTROL |
| select PINCTRL |
| select XIP |
| select HAS_ESPRESSIF_HAL |
| |
| if SOC_ESP32S2 |
| |
| config IDF_TARGET_ESP32S2 |
| bool "ESP32S2 as target board" |
| default y |
| |
| config ESPTOOLPY_FLASHFREQ_80M |
| bool |
| default y |
| |
| config FLASH_SIZE |
| int |
| default $(dt_node_reg_size_int,/soc/flash-controller@3f402000/flash@0,0) |
| |
| config FLASH_BASE_ADDRESS |
| hex |
| default $(dt_node_reg_addr_hex,/soc/flash-controller@3f402000/flash@0) |
| |
| choice |
| prompt "Instruction cache line size" |
| default ESP32S2_INSTRUCTION_CACHE_LINE_32B |
| |
| config ESP32S2_INSTRUCTION_CACHE_LINE_16B |
| bool "16 Bytes" |
| |
| config ESP32S2_INSTRUCTION_CACHE_LINE_32B |
| bool "32 Bytes" |
| |
| endchoice |
| |
| choice |
| prompt "Instruction cache size" |
| default ESP32S2_INSTRUCTION_CACHE_8KB |
| |
| config ESP32S2_INSTRUCTION_CACHE_8KB |
| bool "8KB instruction cache size" |
| |
| config ESP32S2_INSTRUCTION_CACHE_16KB |
| bool "16KB instruction cache size" |
| |
| endchoice |
| |
| choice |
| prompt "Data cache size" |
| default ESP32S2_DATA_CACHE_0KB if !ESP_SPIRAM |
| default ESP32S2_DATA_CACHE_8KB if ESP_SPIRAM |
| |
| config ESP32S2_DATA_CACHE_0KB |
| bool "0KB data cache size" |
| |
| config ESP32S2_DATA_CACHE_8KB |
| bool "8KB data cache size" |
| |
| config ESP32S2_DATA_CACHE_16KB |
| bool "16KB data cache size" |
| |
| endchoice |
| |
| choice |
| prompt "Data cache line size" |
| default ESP32S2_DATA_CACHE_LINE_32B |
| |
| config ESP32S2_DATA_CACHE_LINE_16B |
| bool "16 Bytes" |
| |
| config ESP32S2_DATA_CACHE_LINE_32B |
| bool "32 Bytes" |
| |
| endchoice |
| |
| config ESP32S2_INSTRUCTION_CACHE_SIZE |
| hex |
| default 0x4000 if ESP32S2_INSTRUCTION_CACHE_16KB |
| default 0x2000 |
| |
| config ESP32S2_DATA_CACHE_SIZE |
| hex |
| default 0x2000 if ESP32S2_DATA_CACHE_8KB |
| default 0x4000 if ESP32S2_DATA_CACHE_16KB |
| default 0x0000 |
| |
| config ESP_SPIRAM |
| bool "Support for external, SPI-connected RAM" |
| help |
| This enables support for an external SPI RAM chip, connected in |
| parallel with the main SPI flash chip. |
| |
| config ESP_HEAP_MIN_EXTRAM_THRESHOLD |
| int "Minimum threshold for external RAM allocation" |
| default 8192 |
| range 1024 131072 |
| depends on ESP_SPIRAM |
| help |
| Threshold to decide if memory will be allocated from DRAM |
| or SPIRAM. If value of allocation size is less than this value, |
| memory will be allocated from internal RAM. |
| |
| menu "SPI RAM config" |
| depends on ESP_SPIRAM |
| |
| choice SPIRAM_TYPE |
| prompt "Type of SPI RAM chip in use" |
| default SPIRAM_TYPE_ESPPSRAM16 |
| |
| config SPIRAM_TYPE_ESPPSRAM16 |
| bool "ESP-PSRAM16 or APS1604" |
| |
| config SPIRAM_TYPE_ESPPSRAM32 |
| bool "ESP-PSRAM32 or IS25WP032" |
| |
| config SPIRAM_TYPE_ESPPSRAM64 |
| bool "ESP-PSRAM64 or LY68L6400" |
| |
| endchoice # SPIRAM_TYPE |
| |
| config ESP_SPIRAM_SIZE |
| int "Size of SPIRAM part" |
| default 2097152 if SPIRAM_TYPE_ESPPSRAM16 |
| default 4194304 if SPIRAM_TYPE_ESPPSRAM32 |
| default 8388608 if SPIRAM_TYPE_ESPPSRAM64 |
| help |
| Specify size of SPIRAM part. |
| NOTE: If SPIRAM size is greater than 4MB, only |
| lower 4MB can be allocated using k_malloc(). |
| |
| menu "PSRAM clock and cs IO for ESP32S2" |
| depends on ESP_SPIRAM |
| |
| config DEFAULT_PSRAM_CLK_IO |
| int "PSRAM CLK IO number" |
| range 0 33 |
| default 30 |
| help |
| The PSRAM CLOCK IO can be any unused GPIO, user can config |
| it based on hardware design. |
| |
| config DEFAULT_PSRAM_CS_IO |
| int "PSRAM CS IO number" |
| range 0 33 |
| default 26 |
| help |
| The PSRAM CS IO can be any unused GPIO, user can config it |
| based on hardware design. |
| |
| endmenu # PSRAM clock and cs IO for ESP32S2 |
| |
| choice SPIRAM_SPEED |
| prompt "Set RAM clock speed" |
| default SPIRAM_SPEED_40M |
| help |
| Select the speed for the SPI RAM chip. |
| |
| config SPIRAM_SPEED_80M |
| bool "80MHz clock speed" |
| |
| config SPIRAM_SPEED_40M |
| bool "40MHz clock speed" |
| |
| config SPIRAM_SPEED_26M |
| bool "26MHz clock speed" |
| |
| config SPIRAM_SPEED_20M |
| bool "20MHz clock speed" |
| |
| endchoice # SPIRAM_SPEED |
| |
| config SPIRAM |
| bool |
| default y |
| |
| endmenu # SPI RAM config |
| |
| config ESP_SYSTEM_RTC_EXT_XTAL |
| bool |
| |
| config ESP_SYSTEM_RTC_EXT_OSC |
| bool |
| |
| choice ESP32S2_RTC_CLK_SRC |
| prompt "RTC clock source" |
| default ESP32S2_RTC_CLK_SRC_INT_RC |
| help |
| Choose which clock is used as RTC clock source. |
| |
| - "Internal 90kHz oscillator" option provides lowest deep sleep current |
| consumption, and does not require extra external components. However |
| frequency stability with respect to temperature is poor, so time may |
| drift in deep/light sleep modes. |
| - "External 32kHz crystal" provides better frequency stability, at the |
| expense of slightly higher (1uA) deep sleep current consumption. |
| - "External 32kHz oscillator" allows using 32kHz clock generated by an |
| external circuit. In this case, external clock signal must be connected |
| to 32K_XN pin. Amplitude should be <1.2V in case of sine wave signal, |
| and <1V in case of square wave signal. Common mode voltage should be |
| 0.1 < Vcm < 0.5Vamp, where Vamp is the signal amplitude. |
| Additionally, 1nF capacitor must be connected between 32K_XP pin and |
| ground. 32K_XP pin can not be used as a GPIO in this case. |
| - "Internal 8MHz oscillator divided by 256" option results in higher |
| deep sleep current (by 5uA) but has better frequency stability than |
| the internal 90kHz oscillator. It does not require external components. |
| |
| config ESP32S2_RTC_CLK_SRC_INT_RC |
| bool "Internal 90kHz RC oscillator" |
| |
| config ESP32S2_RTC_CLK_SRC_EXT_CRYS |
| bool "External 32kHz crystal" |
| select ESP_SYSTEM_RTC_EXT_XTAL |
| |
| config ESP32S2_RTC_CLK_SRC_EXT_OSC |
| bool "External 32kHz oscillator at 32K_XN pin" |
| select ESP_SYSTEM_RTC_EXT_OSC |
| |
| config ESP32S2_RTC_CLK_SRC_INT_8MD256 |
| bool "Internal 8MHz oscillator, divided by 256 (~32kHz)" |
| |
| endchoice |
| |
| config ESP32S2_RTC_CLK_CAL_CYCLES |
| int "Number of cycles for RTC_SLOW_CLK calibration" |
| default 3000 if ESP32S2_RTC_CLK_SRC_EXT_CRYS || ESP32S2_RTC_CLK_SRC_EXT_OSC || ESP32S2_RTC_CLK_SRC_INT_8MD256 |
| default 576 if ESP32S2_RTC_CLK_SRC_INT_RC |
| range 0 125000 |
| help |
| When the startup code initializes RTC_SLOW_CLK, it can perform |
| calibration by comparing the RTC_SLOW_CLK frequency with main XTAL |
| frequency. This option sets the number of RTC_SLOW_CLK cycles measured |
| by the calibration routine. Higher numbers increase calibration |
| precision, which may be important for applications which spend a lot of |
| time in deep sleep. Lower numbers reduce startup time. |
| |
| When this option is set to 0, clock calibration will not be performed at |
| startup, and approximate clock frequencies will be assumed: |
| |
| - 90000 Hz if internal RC oscillator is used as clock source. For this use value 1024. |
| - 32768 Hz if the 32k crystal oscillator is used. For this use value 3000 or more. |
| In case more value will help improve the definition of the launch of the crystal. |
| If the crystal could not start, it will be switched to internal RC. |
| |
| choice ESP32S2_UNIVERSAL_MAC_ADDRESSES |
| bool "Number of universally administered (by IEEE) MAC address" |
| default ESP32S2_UNIVERSAL_MAC_ADDRESSES_TWO |
| help |
| Configure the number of universally administered (by IEEE) MAC addresses. |
| During initialization, MAC addresses for each network interface are generated or |
| derived from a single base MAC address. If the number of universal MAC addresses is two, |
| all interfaces (WiFi station, WiFi softap) receive a universally administered MAC |
| address. |
| They are generated sequentially by adding 0, and 1 (respectively) to the final octet of |
| the base MAC address. If the number of universal MAC addresses is one, only WiFi station |
| receives a universally administered MAC address. |
| The WiFi softap receives local MAC addresses. It's derived from the universal WiFi |
| station MAC addresses. |
| When using the default (Espressif-assigned) base MAC address, either setting can be used. |
| When using a custom universal MAC address range, the correct setting will depend on the |
| allocation of MAC addresses in this range (either 1 or 2 per device). |
| |
| config ESP32S2_UNIVERSAL_MAC_ADDRESSES_ONE |
| bool "Two" |
| select ESP_MAC_ADDR_UNIVERSE_WIFI_STA |
| |
| config ESP32S2_UNIVERSAL_MAC_ADDRESSES_TWO |
| bool "Two" |
| select ESP_MAC_ADDR_UNIVERSE_WIFI_STA |
| select ESP_MAC_ADDR_UNIVERSE_WIFI_AP |
| |
| endchoice # ESP32S2_UNIVERSAL_MAC_ADDRESSES |
| |
| config ESP_MAC_ADDR_UNIVERSE_WIFI_AP |
| bool |
| |
| config ESP_MAC_ADDR_UNIVERSE_WIFI_STA |
| bool |
| |
| config ESP32S2_UNIVERSAL_MAC_ADDRESSES |
| int |
| default 1 if ESP32S2_UNIVERSAL_MAC_ADDRESSES_ONE |
| default 2 if ESP32S2_UNIVERSAL_MAC_ADDRESSES_TWO |
| |
| config ESP32_PHY_MAX_WIFI_TX_POWER |
| int "Max WiFi TX power (dBm)" |
| range 10 20 |
| default 20 |
| help |
| Set maximum transmit power for WiFi radio. Actual transmit power for high |
| data rates may be lower than this setting. |
| |
| config ESP32_PHY_MAX_TX_POWER |
| int |
| default ESP32_PHY_MAX_WIFI_TX_POWER |
| |
| endif # SOC_ESP32S2 |
