| # |
| # Copyright (c) 2020 Siddharth Chandrasekaran <siddharth@embedjournal.com> |
| # |
| # SPDX-License-Identifier: Apache-2.0 |
| # |
| |
| # OSDP_NUM_CONNECTED_PD is used in CP mode. It is a constant set to 1 when |
| # operating as a PD. |
| config OSDP_NUM_CONNECTED_PD |
| int |
| default 1 |
| help |
| In PD mode, number of connected PDs is always 1 and cannot |
| be configured. |
| |
| config OSDP_PD_COMMAND_QUEUE_SIZE |
| int "OSDP Peripheral Device command queue size" |
| default 16 |
| help |
| The number of commands that can be queued to a given PD. In CP mode, |
| the queue size is multiplied by number of connected PD so this can grow |
| very quickly. |
| |
| config OSDP_PD_ADDRESS |
| int "Peripheral Device Address" |
| default 1 |
| range 1 126 |
| help |
| The 7 least significant bits represent the address of the PD to which |
| the message is directed, or the address of the PD sending the reply. |
| Address 0x7F is reserved as a broadcast address to which all PDs would |
| respond. |
| |
| if OSDP_SC_ENABLED |
| |
| config OSDP_PD_SCBK |
| string "Secure Channel Base Key (SCBK)" |
| default "NONE" |
| help |
| Hexadecimal string representation of the 16 byte OSDP PD Secure |
| Channel Base Key. When this field is sent to "NONE", the PD is set to |
| "Install Mode". In this mode, the PD would allow a CP to setup a secure |
| channel with default SCBK. Once as secure channel is active with the |
| default key, the CP can send a KEYSET command to set new keys to the PD. |
| It is up to the user to make sure that the PD enters the "Install Mode" |
| only during provisioning time (controlled environment). |
| |
| endif # OSDP_SC_ENABLED |
| |
| menu "Peripheral Device ID Information" |
| |
| config OSDP_PD_ID_VENDOR_CODE |
| hex "PD Vendor Code" |
| default 0x001A2B3C |
| range 0 0x00FFFFFF |
| help |
| IEEE assigned OUI. Least 24 bits are valid. |
| |
| config OSDP_PD_ID_MODEL |
| int "PD Product Model Number" |
| default 1 |
| range 0 $(UINT8_MAX) |
| help |
| Manufacturer's model number. Least 8 bits are valid. |
| |
| config OSDP_PD_ID_VERSION |
| int "PD Product Version" |
| default 1 |
| range 0 $(UINT8_MAX) |
| help |
| Manufacturer's version of this product. Least 8 bits are valid. |
| |
| config OSDP_PD_ID_SERIAL_NUMBER |
| hex "PD Serial Number" |
| default 0xCAFEBABE |
| range 0 0xFFFFFFFF |
| help |
| A 4-byte serial number for the PD. |
| |
| config OSDP_PD_ID_FIRMWARE_VERSION |
| hex "PD Firmware Version" |
| default 0x00010100 |
| range 0 0x00FFFFFF |
| help |
| Firmware revision code. |
| - Bit 0-7 : build version number; |
| - Bit 8-15 : minor version number; |
| - Bit 16-23: major version number; |
| |
| endmenu # "PD ID Information" |
| |
| menu "OSDP PD Capabilities" |
| |
| menu "Contact Status Monitoring" |
| |
| config OSDP_PD_CAP_CONTACT_STATUS_MONITORING_COMP_LEVEL |
| int "Compliance Level" |
| default 0 |
| range 0 4 |
| help |
| Possible values: |
| - 01: PD monitors and reports the state of the circuit without any |
| supervision. The PD encodes the circuit status per its default |
| interpretation of contact state to active/inactive status. |
| - 02: Like 01, plus: The PD accepts configuration of the encoding of the |
| open/closed circuit status to the reported active/inactive status. (User |
| may configure each circuit as "normally closed" or "normally open".) |
| - 03: Like 02, plus: PD supports supervised monitoring. The operating mode |
| for each circuit is determined by configuration settings. |
| - 04: Like 03, plus: the PD supports custom End-Of-Line settings within |
| the Manufacturer's guidelines. |
| |
| config OSDP_PD_CAP_CONTACT_STATUS_MONITORING_NUM_ITEMS |
| int "Number of items" |
| default 0 |
| help |
| The number of Inputs |
| |
| endmenu # "Contact Status Monitoring" |
| |
| menu "Output Control" |
| |
| config OSDP_PD_CAP_OUTPUT_CONTROL_COMP_LEVEL |
| int "Compliance Level" |
| default 0 |
| range 0 4 |
| help |
| Possible values: |
| - 01: The PD is able to activate and deactivate the Output per direct |
| command from the CP. |
| - 02: Like 01, plus: The PD is able to accept configuration of the Output |
| driver to set the inactive state of the Output. The typical state of an |
| inactive Output is the state of the Output when no power is applied to the |
| PD and the output device (relay) is not energized. The inverted drive |
| setting causes the PD to energize the Output during the inactive state and |
| de-energize the Output during the active state. This feature allows the |
| support of "fail-safe/fail-secure" operating modes. |
| - 03: Like 01, plus: The PD is able to accept timed commands to the |
| Output. A timed command specifies the state of the Output for the |
| specified duration. |
| - 04: Like 02 and 03 - normal/inverted drive and timed operation. |
| |
| config OSDP_PD_CAP_OUTPUT_CONTROL_NUM_ITEMS |
| int "Number of items" |
| default 0 |
| help |
| The number of Outputs. |
| |
| endmenu # "Output Control" |
| |
| menu "LED Control" |
| |
| config OSDP_PD_CAP_READER_LED_CONTROL_COMP_LEVEL |
| int "Compliance Level" |
| default 0 |
| range 0 4 |
| help |
| Possible values: |
| - 01: the PD support on/off control only |
| - 02: the PD supports timed commands |
| - 03: like 02, plus bi-color LEDs |
| - 04: like 02, plus tri-color LEDs |
| |
| config OSDP_PD_CAP_READER_LED_CONTROL_NUM_ITEMS |
| int "Number of items" |
| default 0 |
| help |
| The number of LEDs per reader. |
| |
| endmenu # "LED Control" |
| |
| menu "Audible Output" |
| |
| config OSDP_PD_CAP_READER_AUDIBLE_OUTPUT_COMP_LEVEL |
| int "Compliance Level" |
| default 0 |
| range 0 2 |
| help |
| Possible values: |
| - 01: the PD support on/off control only |
| - 02: the PD supports timed commands |
| |
| config OSDP_PD_CAP_READER_AUDIBLE_OUTPUT_NUM_ITEMS |
| int "Number of items" |
| default 0 |
| help |
| The number of audible annunciators per reader |
| |
| endmenu # "Audible Output" |
| |
| menu "Text Output" |
| |
| config OSDP_PD_CAP_READER_TEXT_OUTPUT_COMP_LEVEL |
| int "Compliance Level" |
| default 0 |
| range 0 4 |
| help |
| Possible values: |
| - 00: The PD has no text display support |
| - 01: The PD supports 1 row of 16 characters |
| - 02: the PD supports 2 rows of 16 characters |
| - 03: the PD supports 4 rows of 16 characters |
| - 04: TBD. |
| |
| config OSDP_PD_CAP_READER_TEXT_OUTPUT_NUM_ITEMS |
| int "Number of items" |
| default 0 |
| help |
| Number of textual displays per reader |
| |
| endmenu # "Text Output" |
| |
| menu "Card Data Format" |
| |
| config OSDP_PD_CAP_CARD_DATA_FORMAT_COMP_LEVEL |
| int "Compliance Level" |
| default 0 |
| range 0 3 |
| help |
| Possible values: |
| - 01: the PD sends card data to the CP as array of bits, not exceeding |
| 1024 bits. |
| - 02: the PD sends card data to the CP as array of BCD characters, not |
| exceeding 256 characters. |
| - 03: the PD can send card data to the CP as array of bits, or as an |
| array of BCD characters. |
| |
| endmenu # "Card Data Format" |
| |
| menu "Time Keeping" |
| |
| config OSDP_PD_CAP_TIME_KEEPING_COMP_LEVEL |
| int "Compliance Level" |
| default 0 |
| range 0 2 |
| help |
| Possible values: |
| - 00: The PD does not support time/date functionality |
| - 01: The PD understands time/date settings per Command osdp_TDSET |
| - 02: The PD is able to locally update the time and date |
| |
| endmenu # "Time Keeping" |
| |
| endmenu # "OSDP PD Capabilities" |
