| /dts-v1/; |
| |
| #include <nxp/nxp_k6x.dtsi> |
| |
| / { |
| model = "NXP Freedom MK64F board"; |
| compatible = "nxp,mk64f12", "nxp,k64f", "nxp,k6x"; |
| |
| aliases { |
| adc-0 = &adc0; |
| adc-1 = &adc1; |
| pwm-0 = &pwm0; |
| pwm-1 = &pwm1; |
| pwm-2 = &pwm2; |
| pwm-3 = &pwm3; |
| uart-0 = &uart0; |
| uart-3 = &uart3; |
| pinmux-a = &pinmux_a; |
| pinmux-b = &pinmux_b; |
| pinmux-c = &pinmux_c; |
| pinmux-d = &pinmux_d; |
| pinmux-e = &pinmux_e; |
| gpio-a = &gpioa; |
| gpio-b = &gpiob; |
| gpio-c = &gpioc; |
| gpio-d = &gpiod; |
| gpio-e = &gpioe; |
| i2c-0 = &i2c0; |
| i2c-1 = &i2c1; |
| i2c-2 = &i2c2; |
| led0 = &green_led; |
| led1 = &blue_led; |
| led2 = &red_led; |
| sw0 = &user_button_3; |
| sw1 = &user_button_2; |
| }; |
| |
| chosen { |
| zephyr,sram = &sram0; |
| zephyr,flash = &flash0; |
| zephyr,console = &uart0; |
| #ifdef CONFIG_BT |
| zephyr,bt-uart = &uart3; |
| #endif |
| zephyr,uart-pipe = &uart0; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| red_led: led@0 { |
| gpios = <&gpiob 22 GPIO_INT_ACTIVE_LOW>; |
| label = "User LD1"; |
| }; |
| green_led: led@1 { |
| gpios = <&gpioe 26 GPIO_INT_ACTIVE_LOW>; |
| label = "User LD2"; |
| }; |
| blue_led: led@2 { |
| gpios = <&gpiob 21 GPIO_INT_ACTIVE_LOW>; |
| label = "User LD3"; |
| }; |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| user_button_2: button@0 { |
| label = "User SW2"; |
| gpios = <&gpioc 6 GPIO_INT_ACTIVE_LOW>; |
| }; |
| user_button_3: button@1 { |
| label = "User SW3"; |
| gpios = <&gpioa 4 GPIO_INT_ACTIVE_LOW>; |
| }; |
| }; |
| }; |
| |
| &adc0 { |
| status = "ok"; |
| }; |
| |
| &adc1 { |
| status = "ok"; |
| }; |
| |
| &i2c0 { |
| status = "ok"; |
| |
| fxos8700@1d { |
| compatible = "nxp,fxos8700"; |
| reg = <0x1d>; |
| label = "FXOS8700"; |
| int1-gpios = <&gpioc 6 0>; |
| int2-gpios = <&gpioc 13 0>; |
| }; |
| }; |
| |
| &spi0 { |
| status = "ok"; |
| cs-gpios = <&gpiod 0 0>; |
| |
| mcr20a@0 { |
| compatible = "nxp,mcr20a"; |
| reg = <0x0>; |
| label = "mcr20a"; |
| spi-max-frequency = <4000000>; |
| irqb-gpios = <&gpiob 9 0>; |
| reset-gpios = <&gpioa 2 0>; |
| status = "ok"; |
| }; |
| }; |
| |
| &pwm3 { |
| status = "ok"; |
| }; |
| |
| &uart0 { |
| status = "ok"; |
| current-speed = <115200>; |
| }; |
| |
| #ifdef CONFIG_UART_MCUX_2 |
| &uart2 { |
| status = "ok"; |
| current-speed = <115200>; |
| |
| #ifdef CONFIG_MODEM_WNCM14A2A |
| wncm14a2a { |
| compatible = "wnc,m14a2a"; |
| label = "wncm14a2a"; |
| mdm-boot-mode-sel-gpios = <&gpioc 17 0>; |
| mdm-power-gpios = <&gpiob 9 0>; |
| mdm-keep-awake-gpios = <&gpioc 2 0>; |
| mdm-reset-gpios = <&gpioc 12 0>; |
| mdm-shld-trans-ena-gpios = <&gpioc 4 0>; |
| mdm-send-ok-gpios = <&gpiod 0 0>; |
| status = "ok"; |
| }; |
| #endif |
| }; |
| #endif |
| |
| #ifdef CONFIG_BT |
| &uart3 { |
| status = "ok"; |
| current-speed = <115200>; |
| }; |
| #endif |
| |
| &usbd { |
| compatible = "nxp,kinetis-usbd"; |
| status = "ok"; |
| num-bidir-endpoints = <8>; |
| }; |
| |
| &flash0 { |
| /* |
| * For more information, see: |
| * http://docs.zephyrproject.org/devices/dts/flash_partitions.html |
| */ |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x00000000 0x00010000>; |
| read-only; |
| }; |
| |
| /* |
| * The flash starting at 0x00010000 and ending at |
| * 0x0001ffff (sectors 16-31) is reserved for use |
| * by the application. |
| */ |
| #if defined(CONFIG_FS_FLASH_STORAGE_PARTITION) |
| storage_partition: partition@1e000 { |
| label = "storage"; |
| reg = <0x0001e000 0x00002000>; |
| }; |
| #endif |
| |
| slot0_partition: partition@20000 { |
| label = "image-0"; |
| reg = <0x00020000 0x00060000>; |
| }; |
| slot1_partition: partition@80000 { |
| label = "image-1"; |
| reg = <0x00080000 0x00060000>; |
| }; |
| scratch_partition: partition@e0000 { |
| label = "image-scratch"; |
| reg = <0x000e0000 0x00020000>; |
| }; |
| }; |
| }; |