| /* |
| * Copyright (c) 2021 Nordic Semiconductor ASA |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /dts-v1/; |
| #include <nordic/nrf5340_cpunet_qkaa.dtsi> |
| #include "thingy53_nrf5340_cpunet-pinctrl.dtsi" |
| |
| / { |
| model = "Nordic Thingy53 NRF5340 Network"; |
| compatible = "nordic,thingy53-nrf5340-cpunet"; |
| |
| chosen { |
| zephyr,console = &uart0; |
| zephyr,shell-uart = &uart0; |
| zephyr,uart-mcumgr = &uart0; |
| zephyr,bt-mon-uart = &uart0; |
| zephyr,bt-c2h-uart = &uart0; |
| zephyr,bt-hci-rpmsg-ipc = &ipc0; |
| nordic,802154-spinel-ipc = &ipc0; |
| zephyr,sram = &sram1; |
| zephyr,flash = &flash1; |
| zephyr,code-partition = &slot0_partition; |
| zephyr,ieee802154 = &ieee802154; |
| }; |
| |
| buttons { |
| compatible = "gpio-keys"; |
| button0: button_0 { |
| gpios = <&gpio1 14 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; |
| label = "Push button 1"; |
| }; |
| button1: button_1 { |
| gpios = <&gpio1 13 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; |
| label = "Push button 2"; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| red_led: led_1 { |
| gpios = <&gpio1 8 (GPIO_PULL_DOWN | GPIO_ACTIVE_HIGH)>; |
| label = "RGB red LED"; |
| }; |
| green_led: led_2 { |
| gpios = <&gpio1 6 (GPIO_PULL_DOWN | GPIO_ACTIVE_HIGH)>; |
| label = "RGB green LED"; |
| }; |
| blue_led: led_3 { |
| gpios = <&gpio1 7 (GPIO_PULL_DOWN | GPIO_ACTIVE_HIGH)>; |
| label = "RGB blue LED"; |
| }; |
| }; |
| |
| nrf_radio_fem: fem { |
| compatible = "nordic,nrf21540-fem"; |
| rx-en-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; |
| mode-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>; |
| pdn-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; |
| tx-en-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>; |
| supply-voltage-mv = <3000>; |
| }; |
| |
| aliases { |
| sw0 = &button0; |
| sw1 = &button1; |
| led0 = &red_led; |
| led1 = &green_led; |
| led2 = &blue_led; |
| watchdog0 = &wdt; |
| }; |
| }; |
| |
| &gpiote { |
| status = "okay"; |
| }; |
| |
| &gpio0 { |
| status = "okay"; |
| }; |
| |
| &gpio1 { |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| compatible = "nordic,nrf-uarte"; |
| status = "disabled"; |
| current-speed = <115200>; |
| pinctrl-0 = <&uart0_default>; |
| pinctrl-1 = <&uart0_sleep>; |
| pinctrl-names = "default", "sleep"; |
| }; |
| |
| &flash1 { |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x00000000 0xc000>; |
| }; |
| slot0_partition: partition@c000 { |
| label = "image-0"; |
| reg = <0x0000C000 0x12000>; |
| }; |
| slot1_partition: partition@1e000 { |
| label = "image-1"; |
| reg = <0x0001E000 0x12000>; |
| }; |
| scratch_partition: partition@30000 { |
| label = "image-scratch"; |
| reg = <0x00030000 0xa000>; |
| }; |
| storage_partition: partition@3a000 { |
| label = "storage"; |
| reg = <0x0003a000 0x6000>; |
| }; |
| }; |
| }; |
| |
| &ieee802154 { |
| status = "okay"; |
| }; |
| |
| /* Include shared RAM configuration file */ |
| #include "thingy53_nrf5340_shared_sram_planning_conf.dtsi" |