| /* |
| * Copyright (c) 2019 Intel Corporation. |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /** |
| * @file |
| * @brief Public APIs for eSPI driver |
| */ |
| |
| #ifndef ZEPHYR_INCLUDE_ESPI_H_ |
| #define ZEPHYR_INCLUDE_ESPI_H_ |
| |
| #include <sys/__assert.h> |
| #include <zephyr/types.h> |
| #include <device.h> |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /** |
| * @brief eSPI Driver APIs |
| * @defgroup espi_interface ESPI Driver APIs |
| * @ingroup io_interfaces |
| * @{ |
| */ |
| |
| /** |
| * @brief eSPI I/O mode capabilities |
| */ |
| enum espi_io_mode { |
| ESPI_IO_MODE_SINGLE_LINE = BIT(0), |
| ESPI_IO_MODE_DUAL_LINES = BIT(1), |
| ESPI_IO_MODE_QUAD_LINES = BIT(2), |
| }; |
| |
| /** |
| *+----------------------------------------------------------------------+ |
| *| | |
| *| eSPI host +-------------+ | |
| *| +-----------+ | Power | +----------+ | |
| *| |Out of band| | management | | GPIO | | |
| *| +------------+ |processor | | controller | | sources | | |
| *| | SPI flash | +-----------+ +-------------+ +----------+ | |
| *| | controller | | | | | |
| *| +------------+ | | | | |
| *| | | | +--------+ +---------------+ | |
| *| | | | | | | |
| *| | | +-----+ +--------+ +----------+ +----v-----+ | |
| *| | | | | LPC | | Tunneled | | Tunneled | | |
| *| | | | | bridge | | SMBus | | GPIO | | |
| *| | | | +--------+ +----------+ +----------+ | |
| *| | | | | | | | |
| *| | | | ------+ | | | |
| *| | | | | | | | |
| *| | | +------v-----+ +---v-------v-------------v----+ | |
| *| | | | eSPI Flash | | eSPI protocol block | | |
| *| | | | access +--->+ | | |
| *| | | +------------+ +------------------------------+ | |
| *| | | | | |
| *| | +-----------+ | | |
| *| | v v | |
| *| | XXXXXXXXXXXXXXXXXXXXXXX | |
| *| | XXXXXXXXXXXXXXXXXXXXX | |
| *| | XXXXXXXXXXXXXXXXXXX | |
| *+----------------------------------------------------------------------+ |
| * | | |
| * v +-----------------+ |
| * +---------+ | | | | | | |
| * | Flash | | | | | | | |
| * +---------+ | + + + + | eSPI bus |
| * | CH0 CH1 CH2 CH3 | (logical channels) |
| * | + + + + | |
| * | | | | | | |
| * +-----------------+ |
| * | |
| *+-----------------------------------------------------------------------+ |
| *| eSPI slave | |
| *| | |
| *| CH0 | CH1 | CH2 | CH3 | |
| *| eSPI endpoint | VWIRE | OOB | Flash | |
| *+-----------------------------------------------------------------------+ |
| * |
| */ |
| |
| /** |
| * @brief eSPI channel. |
| * |
| * Identifies each eSPI logical channel supported by eSPI controller |
| * Each channel allows independent traffic, but the assignment of channel |
| * type to channel number is fixed. |
| * |
| * Note that generic commands are not associated with any channel, so traffic |
| * over eSPI can occur if all channels are disabled or not ready |
| */ |
| enum espi_channel { |
| ESPI_CHANNEL_PERIPHERAL = BIT(0), |
| ESPI_CHANNEL_VWIRE = BIT(1), |
| ESPI_CHANNEL_OOB = BIT(2), |
| ESPI_CHANNEL_FLASH = BIT(3), |
| }; |
| |
| /** |
| * @brief eSPI bus event. |
| * |
| * eSPI bus event to indicate events for which user can register callbacks |
| */ |
| enum espi_bus_event { |
| ESPI_BUS_RESET = BIT(0), |
| ESPI_BUS_EVENT_CHANNEL_READY = BIT(1), |
| ESPI_BUS_EVENT_VWIRE_RECEIVED = BIT(2), |
| ESPI_BUS_EVENT_OOB_RECEIVED = BIT(3), |
| ESPI_BUS_PERIPHERAL_NOTIFICATION = BIT(4), |
| }; |
| |
| /** |
| * @cond INTERNAL_HIDDEN |
| * |
| */ |
| #define ESPI_PERIPHERAL_INDEX_0 0ul |
| #define ESPI_PERIPHERAL_INDEX_1 1ul |
| #define ESPI_PERIPHERAL_INDEX_2 2ul |
| |
| #define ESPI_SLAVE_TO_MASTER 0ul |
| #define ESPI_MASTER_TO_SLAVE 1ul |
| |
| #define ESPI_VWIRE_SRC_ID0 0ul |
| #define ESPI_VWIRE_SRC_ID1 1ul |
| #define ESPI_VWIRE_SRC_ID2 2ul |
| #define ESPI_VWIRE_SRC_ID3 3ul |
| #define ESPI_VWIRE_SRC_ID_MAX 4ul |
| |
| #define ESPI_PERIPHERAL_NODATA 0ul |
| |
| #define E8042_START_OPCODE 0x50 |
| #define E8042_MAX_OPCODE 0x5F |
| |
| #define EACPI_START_OPCODE 0x60 |
| #define EACPI_MAX_OPCODE 0x6F |
| |
| #define ECUSTOM_START_OPCODE 0xF0 |
| #define ECUSTOM_MAX_OPCODE 0xFF |
| |
| /** @endcond */ |
| |
| /** |
| * @brief eSPI peripheral notification type. |
| * |
| * eSPI peripheral notification event details to indicate which peripheral |
| * trigger the eSPI callback |
| */ |
| enum espi_virtual_peripheral { |
| ESPI_PERIPHERAL_UART, |
| ESPI_PERIPHERAL_8042_KBC, |
| ESPI_PERIPHERAL_HOST_IO, |
| ESPI_PERIPHERAL_DEBUG_PORT80, |
| ESPI_PERIPHERAL_HOST_IO_PVT, |
| #if defined(CONFIG_ESPI_PERIPHERAL_EC_HOST_CMD) |
| ESPI_PERIPHERAL_EC_HOST_CMD, |
| #endif /* CONFIG_ESPI_PERIPHERAL_EC_HOST_CMD */ |
| }; |
| |
| /** |
| * @brief eSPI cycle types supported over eSPI peripheral channel |
| */ |
| enum espi_cycle_type { |
| ESPI_CYCLE_MEMORY_READ32, |
| ESPI_CYCLE_MEMORY_READ64, |
| ESPI_CYCLE_MEMORY_WRITE32, |
| ESPI_CYCLE_MEMORY_WRITE64, |
| ESPI_CYCLE_MESSAGE_NODATA, |
| ESPI_CYCLE_MESSAGE_DATA, |
| ESPI_CYCLE_OK_COMPLETION_NODATA, |
| ESPI_CYCLE_OKCOMPLETION_DATA, |
| ESPI_CYCLE_NOK_COMPLETION_NODATA, |
| }; |
| |
| /** |
| * @brief eSPI system platform signals that can be send or receive through |
| * virtual wire channel |
| */ |
| enum espi_vwire_signal { |
| /* Virtual wires that can only be send from master to slave */ |
| ESPI_VWIRE_SIGNAL_SLP_S3, |
| ESPI_VWIRE_SIGNAL_SLP_S4, |
| ESPI_VWIRE_SIGNAL_SLP_S5, |
| ESPI_VWIRE_SIGNAL_OOB_RST_WARN, |
| ESPI_VWIRE_SIGNAL_PLTRST, |
| ESPI_VWIRE_SIGNAL_SUS_STAT, |
| ESPI_VWIRE_SIGNAL_NMIOUT, |
| ESPI_VWIRE_SIGNAL_SMIOUT, |
| ESPI_VWIRE_SIGNAL_HOST_RST_WARN, |
| ESPI_VWIRE_SIGNAL_SLP_A, |
| ESPI_VWIRE_SIGNAL_SUS_PWRDN_ACK, |
| ESPI_VWIRE_SIGNAL_SUS_WARN, |
| ESPI_VWIRE_SIGNAL_SLP_WLAN, |
| ESPI_VWIRE_SIGNAL_SLP_LAN, |
| ESPI_VWIRE_SIGNAL_HOST_C10, |
| ESPI_VWIRE_SIGNAL_DNX_WARN, |
| /* Virtual wires that can only be send from slave to master */ |
| ESPI_VWIRE_SIGNAL_PME, |
| ESPI_VWIRE_SIGNAL_WAKE, |
| ESPI_VWIRE_SIGNAL_OOB_RST_ACK, |
| ESPI_VWIRE_SIGNAL_SLV_BOOT_STS, |
| ESPI_VWIRE_SIGNAL_ERR_NON_FATAL, |
| ESPI_VWIRE_SIGNAL_ERR_FATAL, |
| ESPI_VWIRE_SIGNAL_SLV_BOOT_DONE, |
| ESPI_VWIRE_SIGNAL_HOST_RST_ACK, |
| ESPI_VWIRE_SIGNAL_RST_CPU_INIT, |
| /* System management interrupt */ |
| ESPI_VWIRE_SIGNAL_SMI, |
| /* System control interrupt */ |
| ESPI_VWIRE_SIGNAL_SCI, |
| ESPI_VWIRE_SIGNAL_DNX_ACK, |
| ESPI_VWIRE_SIGNAL_SUS_ACK, |
| }; |
| |
| /* eSPI LPC peripherals. */ |
| enum lpc_peripheral_opcode { |
| /* Read transactions */ |
| E8042_OBF_HAS_CHAR = 0x50, |
| E8042_IBF_HAS_CHAR, |
| /* Write transactions */ |
| E8042_WRITE_KB_CHAR, |
| E8042_WRITE_MB_CHAR, |
| /* Write transactions without input parameters */ |
| E8042_RESUME_IRQ, |
| E8042_PAUSE_IRQ, |
| E8042_CLEAR_OBF, |
| /* Status transactions */ |
| E8042_READ_KB_STS, |
| E8042_SET_FLAG, |
| E8042_CLEAR_FLAG, |
| /* ACPI read transactions */ |
| EACPI_OBF_HAS_CHAR = EACPI_START_OPCODE, |
| EACPI_IBF_HAS_CHAR, |
| /* ACPI write transactions */ |
| EACPI_WRITE_CHAR, |
| /* ACPI status transactions */ |
| EACPI_READ_STS, |
| EACPI_WRITE_STS, |
| #if defined(CONFIG_ESPI_PERIPHERAL_ACPI_SHM_REGION) |
| /* Shared memory region support to return the ACPI response data */ |
| EACPI_GET_SHARED_MEMORY, |
| #endif /* CONFIG_ESPI_PERIPHERAL_ACPI_SHM_REGION */ |
| #if defined(CONFIG_ESPI_PERIPHERAL_CUSTOM_OPCODE) |
| /* Other customized transactions */ |
| ECUSTOM_HOST_SUBS_INTERRUPT_EN = ECUSTOM_START_OPCODE, |
| ECUSTOM_HOST_CMD_GET_PARAM_MEMORY, |
| ECUSTOM_HOST_CMD_SEND_RESULT, |
| #endif /* CONFIG_ESPI_PERIPHERAL_CUSTOM_OPCODE */ |
| }; |
| |
| /** |
| * @brief eSPI event |
| */ |
| struct espi_event { |
| /** Event type */ |
| enum espi_bus_event evt_type; |
| /** Additional details for bus event type */ |
| uint32_t evt_details; |
| /** Data associated to the event */ |
| uint32_t evt_data; |
| }; |
| |
| /** |
| * @brief eSPI bus configuration parameters |
| */ |
| struct espi_cfg { |
| /** Supported I/O mode */ |
| enum espi_io_mode io_caps; |
| /** Supported channels */ |
| enum espi_channel channel_caps; |
| /** Maximum supported frequency in MHz */ |
| uint8_t max_freq; |
| }; |
| |
| /** |
| * @brief eSPI peripheral request packet format |
| */ |
| struct espi_request_packet { |
| enum espi_cycle_type cycle_type; |
| uint8_t tag; |
| uint16_t len; |
| uint32_t address; |
| uint8_t *data; |
| }; |
| |
| /** |
| * @brief eSPI out-of-band transaction packet format |
| */ |
| struct espi_oob_packet { |
| uint8_t *buf; |
| uint16_t len; |
| }; |
| |
| /** |
| * @brief eSPI flash transactions packet format |
| */ |
| struct espi_flash_packet { |
| uint8_t *buf; |
| uint32_t flash_addr; |
| uint16_t len; |
| }; |
| |
| struct espi_callback; |
| |
| /** |
| * @typedef espi_callback_handler_t |
| * @brief Define the application callback handler function signature. |
| * |
| * @param dev Device struct for the eSPI device. |
| * @param cb Original struct espi_callback owning this handler. |
| * @param espi_evt event details that trigger the callback handler. |
| * |
| */ |
| typedef void (*espi_callback_handler_t) (const struct device *dev, |
| struct espi_callback *cb, |
| struct espi_event espi_evt); |
| |
| /** |
| * @cond INTERNAL_HIDDEN |
| * |
| * Used to register a callback in the driver instance callback list. |
| * As many callbacks as needed can be added as long as each of them |
| * are unique pointers of struct espi_callback. |
| * Beware such structure should not be allocated on stack. |
| * |
| * Note: To help setting it, see espi_init_callback() below |
| */ |
| struct espi_callback { |
| /** This is meant to be used in the driver only */ |
| sys_snode_t node; |
| |
| /** Actual callback function being called when relevant */ |
| espi_callback_handler_t handler; |
| |
| /** An event which user is interested in, if 0 the callback |
| * will never be called. Such evt_mask can be modified whenever |
| * necessary by the owner, and thus will affect the handler being |
| * called or not. |
| */ |
| enum espi_bus_event evt_type; |
| }; |
| /** @endcond */ |
| |
| /** |
| * @cond INTERNAL_HIDDEN |
| * |
| * eSPI driver API definition and system call entry points |
| * |
| * (Internal use only.) |
| */ |
| typedef int (*espi_api_config)(const struct device *dev, struct espi_cfg *cfg); |
| typedef bool (*espi_api_get_channel_status)(const struct device *dev, |
| enum espi_channel ch); |
| /* Logical Channel 0 APIs */ |
| typedef int (*espi_api_read_request)(const struct device *dev, |
| struct espi_request_packet *req); |
| typedef int (*espi_api_write_request)(const struct device *dev, |
| struct espi_request_packet *req); |
| typedef int (*espi_api_lpc_read_request)(const struct device *dev, |
| enum lpc_peripheral_opcode op, |
| uint32_t *data); |
| typedef int (*espi_api_lpc_write_request)(const struct device *dev, |
| enum lpc_peripheral_opcode op, |
| uint32_t *data); |
| /* Logical Channel 1 APIs */ |
| typedef int (*espi_api_send_vwire)(const struct device *dev, |
| enum espi_vwire_signal vw, |
| uint8_t level); |
| typedef int (*espi_api_receive_vwire)(const struct device *dev, |
| enum espi_vwire_signal vw, |
| uint8_t *level); |
| /* Logical Channel 2 APIs */ |
| typedef int (*espi_api_send_oob)(const struct device *dev, |
| struct espi_oob_packet *pckt); |
| typedef int (*espi_api_receive_oob)(const struct device *dev, |
| struct espi_oob_packet *pckt); |
| /* Logical Channel 3 APIs */ |
| typedef int (*espi_api_flash_read)(const struct device *dev, |
| struct espi_flash_packet *pckt); |
| typedef int (*espi_api_flash_write)(const struct device *dev, |
| struct espi_flash_packet *pckt); |
| typedef int (*espi_api_flash_erase)(const struct device *dev, |
| struct espi_flash_packet *pckt); |
| /* Callbacks and traffic intercept */ |
| typedef int (*espi_api_manage_callback)(const struct device *dev, |
| struct espi_callback *callback, |
| bool set); |
| |
| __subsystem struct espi_driver_api { |
| espi_api_config config; |
| espi_api_get_channel_status get_channel_status; |
| espi_api_read_request read_request; |
| espi_api_write_request write_request; |
| espi_api_lpc_read_request read_lpc_request; |
| espi_api_lpc_write_request write_lpc_request; |
| espi_api_send_vwire send_vwire; |
| espi_api_receive_vwire receive_vwire; |
| espi_api_send_oob send_oob; |
| espi_api_receive_oob receive_oob; |
| espi_api_flash_read flash_read; |
| espi_api_flash_write flash_write; |
| espi_api_flash_erase flash_erase; |
| espi_api_manage_callback manage_callback; |
| }; |
| |
| /** |
| * @endcond |
| */ |
| |
| /** |
| * @brief Configure operation of a eSPI controller. |
| * |
| * This routine provides a generic interface to override eSPI controller |
| * capabilities. |
| * |
| * If this eSPI controller is acting as slave, the values set here |
| * will be discovered as part through the GET_CONFIGURATION command |
| * issued by the eSPI master during initialization. |
| * |
| * If this eSPI controller is acting as master, the values set here |
| * will be used by eSPI master to determine minimum common capabilities with |
| * eSPI slave then send via SET_CONFIGURATION command. |
| * |
| * +--------+ +---------+ +------+ +---------+ +---------+ |
| * | eSPI | | eSPI | | eSPI | | eSPI | | eSPI | |
| * | slave | | driver | | bus | | driver | | host | |
| * +--------+ +---------+ +------+ +---------+ +---------+ |
| * | | | | | |
| * | espi_config | Set eSPI | Set eSPI | espi_config | |
| * +--------------+ ctrl regs | cap ctrl reg| +-----------+ |
| * | +-------+ | +--------+ | |
| * | |<------+ | +------->| | |
| * | | | | | |
| * | | | | | |
| * | | | GET_CONFIGURATION | | |
| * | | +<------------------+ | |
| * | |<-----------| | | |
| * | | eSPI caps | | | |
| * | |----------->+ response | | |
| * | | |------------------>+ | |
| * | | | | | |
| * | | | SET_CONFIGURATION | | |
| * | | +<------------------+ | |
| * | | | accept | | |
| * | | +------------------>+ | |
| * + + + + + |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param cfg the device runtime configuration for the eSPI controller. |
| * |
| * @retval 0 If successful. |
| * @retval -EIO General input / output error, failed to configure device. |
| * @retval -EINVAL invalid capabilities, failed to configure device. |
| * @retval -ENOTSUP capability not supported by eSPI slave. |
| */ |
| __syscall int espi_config(const struct device *dev, struct espi_cfg *cfg); |
| |
| static inline int z_impl_espi_config(const struct device *dev, |
| struct espi_cfg *cfg) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| return api->config(dev, cfg); |
| } |
| |
| /** |
| * @brief Query to see if it a channel is ready. |
| * |
| * This routine allows to check if logical channel is ready before use. |
| * Note that queries for channels not supported will always return false. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param ch the eSPI channel for which status is to be retrieved. |
| * |
| * @retval true If eSPI channel is ready. |
| * @retval false otherwise. |
| */ |
| __syscall bool espi_get_channel_status(const struct device *dev, |
| enum espi_channel ch); |
| |
| static inline bool z_impl_espi_get_channel_status(const struct device *dev, |
| enum espi_channel ch) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| return api->get_channel_status(dev, ch); |
| } |
| |
| /** |
| * @brief Sends memory, I/O or message read request over eSPI. |
| * |
| * This routines provides a generic interface to send a read request packet. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param req Address of structure representing a memory, |
| * I/O or message read request. |
| * |
| * @retval 0 If successful. |
| * @retval -ENOTSUP if eSPI controller doesn't support raw packets and instead |
| * low memory transactions are handled by controller hardware directly. |
| * @retval -EIO General input / output error, failed to send over the bus. |
| */ |
| __syscall int espi_read_request(const struct device *dev, |
| struct espi_request_packet *req); |
| |
| static inline int z_impl_espi_read_request(const struct device *dev, |
| struct espi_request_packet *req) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->read_request) { |
| return -ENOTSUP; |
| } |
| |
| return api->read_request(dev, req); |
| } |
| |
| /** |
| * @brief Sends memory, I/O or message write request over eSPI. |
| * |
| * This routines provides a generic interface to send a write request packet. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param req Address of structure representing a memory, I/O or |
| * message write request. |
| * |
| * @retval 0 If successful. |
| * @retval -ENOTSUP if eSPI controller doesn't support raw packets and instead |
| * low memory transactions are handled by controller hardware directly. |
| * @retval -EINVAL General input / output error, failed to send over the bus. |
| */ |
| __syscall int espi_write_request(const struct device *dev, |
| struct espi_request_packet *req); |
| |
| static inline int z_impl_espi_write_request(const struct device *dev, |
| struct espi_request_packet *req) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->write_request) { |
| return -ENOTSUP; |
| } |
| |
| return api->write_request(dev, req); |
| } |
| |
| /** |
| * @brief Reads SOC data from a LPC peripheral with information |
| * updated over eSPI. |
| * |
| * This routine provides a generic interface to read a block whose |
| * information was updated by an eSPI transaction. Reading may trigger |
| * a transaction. The eSPI packet is assembled by the HW block. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param op Enum representing opcode for peripheral type and read request. |
| * @param data Parameter to be read from to the LPC peripheral. |
| * |
| * @retval 0 If successful. |
| * @retval -ENOTSUP if eSPI peripheral is off or not supported. |
| * @retval -EINVAL for unimplemented lpc opcode, but in range. |
| */ |
| __syscall int espi_read_lpc_request(const struct device *dev, |
| enum lpc_peripheral_opcode op, |
| uint32_t *data); |
| |
| static inline int z_impl_espi_read_lpc_request(const struct device *dev, |
| enum lpc_peripheral_opcode op, |
| uint32_t *data) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->read_lpc_request) { |
| return -ENOTSUP; |
| } |
| |
| return api->read_lpc_request(dev, op, data); |
| } |
| |
| /** |
| * @brief Writes data to a LPC peripheral which generates an eSPI transaction. |
| * |
| * This routine provides a generic interface to write data to a block which |
| * triggers an eSPI transaction. The eSPI packet is assembled by the HW |
| * block. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param op Enum representing an opcode for peripheral type and write request. |
| * @param data Represents the parameter passed to the LPC peripheral. |
| * |
| * @retval 0 If successful. |
| * @retval -ENOTSUP if eSPI peripheral is off or not supported. |
| * @retval -EINVAL for unimplemented lpc opcode, but in range. |
| */ |
| __syscall int espi_write_lpc_request(const struct device *dev, |
| enum lpc_peripheral_opcode op, |
| uint32_t *data); |
| |
| static inline int z_impl_espi_write_lpc_request(const struct device *dev, |
| enum lpc_peripheral_opcode op, |
| uint32_t *data) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->write_lpc_request) { |
| return -ENOTSUP; |
| } |
| |
| return api->write_lpc_request(dev, op, data); |
| } |
| |
| /** |
| * @brief Sends system/platform signal as a virtual wire packet. |
| * |
| * This routines provides a generic interface to send a virtual wire packet |
| * from slave to master. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param signal The signal to be send to eSPI master. |
| * @param level The level of signal requested LOW or HIGH. |
| * |
| * @retval 0 If successful. |
| * @retval -EIO General input / output error, failed to send over the bus. |
| */ |
| __syscall int espi_send_vwire(const struct device *dev, |
| enum espi_vwire_signal signal, |
| uint8_t level); |
| |
| static inline int z_impl_espi_send_vwire(const struct device *dev, |
| enum espi_vwire_signal signal, |
| uint8_t level) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| return api->send_vwire(dev, signal, level); |
| } |
| |
| /** |
| * @brief Retrieves level status for a signal encapsulated in a virtual wire. |
| * |
| * This routines provides a generic interface to request a virtual wire packet |
| * from eSPI master and retrieve the signal level. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param signal the signal to be requested from eSPI master. |
| * @param level the level of signal requested 0b LOW, 1b HIGH. |
| * |
| * @retval -EIO General input / output error, failed request to master. |
| */ |
| __syscall int espi_receive_vwire(const struct device *dev, |
| enum espi_vwire_signal signal, |
| uint8_t *level); |
| |
| static inline int z_impl_espi_receive_vwire(const struct device *dev, |
| enum espi_vwire_signal signal, |
| uint8_t *level) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| return api->receive_vwire(dev, signal, level); |
| } |
| |
| /** |
| * @brief Sends SMBus transaction (out-of-band) packet over eSPI bus. |
| * |
| * This routines provides an interface to encapsulate a SMBus transaction |
| * and send into packet over eSPI bus |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param pckt Address of the packet representation of SMBus transaction. |
| * |
| * @retval -EIO General input / output error, failed request to master. |
| */ |
| __syscall int espi_send_oob(const struct device *dev, |
| struct espi_oob_packet *pckt); |
| |
| static inline int z_impl_espi_send_oob(const struct device *dev, |
| struct espi_oob_packet *pckt) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->send_oob) { |
| return -ENOTSUP; |
| } |
| |
| return api->send_oob(dev, pckt); |
| } |
| |
| /** |
| * @brief Receives SMBus transaction (out-of-band) packet from eSPI bus. |
| * |
| * This routines provides an interface to receive and decoded a SMBus |
| * transaction from eSPI bus |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param pckt Address of the packet representation of SMBus transaction. |
| * |
| * @retval -EIO General input / output error, failed request to master. |
| */ |
| __syscall int espi_receive_oob(const struct device *dev, |
| struct espi_oob_packet *pckt); |
| |
| static inline int z_impl_espi_receive_oob(const struct device *dev, |
| struct espi_oob_packet *pckt) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->receive_oob) { |
| return -ENOTSUP; |
| } |
| |
| return api->receive_oob(dev, pckt); |
| } |
| |
| /** |
| * @brief Sends a read request packet for shared flash. |
| * |
| * This routines provides an interface to send a request to read the flash |
| * component shared between the eSPI master and eSPI slaves. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param pckt Adddress of the representation of read flash transaction. |
| * |
| * @retval -ENOTSUP eSPI flash logical channel transactions not supported. |
| * @retval -EBUSY eSPI flash channel is not ready or disabled by master. |
| * @retval -EIO General input / output error, failed request to master. |
| */ |
| __syscall int espi_read_flash(const struct device *dev, |
| struct espi_flash_packet *pckt); |
| |
| static inline int z_impl_espi_read_flash(const struct device *dev, |
| struct espi_flash_packet *pckt) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->flash_read) { |
| return -ENOTSUP; |
| } |
| |
| return api->flash_read(dev, pckt); |
| } |
| |
| /** |
| * @brief Sends a write request packet for shared flash. |
| * |
| * This routines provides an interface to send a request to write to the flash |
| * components shared between the eSPI master and eSPI slaves. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param pckt Address of the representation of write flash transaction. |
| * |
| * @retval -ENOTSUP eSPI flash logical channel transactions not supported. |
| * @retval -EBUSY eSPI flash channel is not ready or disabled by master. |
| * @retval -EIO General input / output error, failed request to master. |
| */ |
| __syscall int espi_write_flash(const struct device *dev, |
| struct espi_flash_packet *pckt); |
| |
| static inline int z_impl_espi_write_flash(const struct device *dev, |
| struct espi_flash_packet *pckt) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->flash_write) { |
| return -ENOTSUP; |
| } |
| |
| return api->flash_write(dev, pckt); |
| } |
| |
| /** |
| * @brief Sends a write request packet for shared flash. |
| * |
| * This routines provides an interface to send a request to write to the flash |
| * components shared between the eSPI master and eSPI slaves. |
| * |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param pckt Address of the representation of write flash transaction. |
| * |
| * @retval -ENOTSUP eSPI flash logical channel transactions not supported. |
| * @retval -EBUSY eSPI flash channel is not ready or disabled by master. |
| * @retval -EIO General input / output error, failed request to master. |
| */ |
| __syscall int espi_flash_erase(const struct device *dev, |
| struct espi_flash_packet *pckt); |
| |
| static inline int z_impl_espi_flash_erase(const struct device *dev, |
| struct espi_flash_packet *pckt) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->flash_erase) { |
| return -ENOTSUP; |
| } |
| |
| return api->flash_erase(dev, pckt); |
| } |
| |
| /** |
| * Callback model |
| * |
| *+-------+ +-------------+ +------+ +---------+ |
| *| App | | eSPI driver | | HW | |eSPI Host| |
| *+---+---+ +-------+-----+ +---+--+ +----+----+ |
| * | | | | |
| * | espi_init_callback | | | |
| * +----------------------------> | | | |
| * | espi_add_callback | | |
| * +----------------------------->+ | |
| * | | | eSPI reset | eSPI host |
| * | | IRQ +<------------+ resets the |
| * | | <-----------+ | bus |
| * | | | | |
| * | | Processed | | |
| * | | within the | | |
| * | | driver | | |
| * | | | | |
| |
| * | | | VW CH ready| eSPI host |
| * | | IRQ +<------------+ enables VW |
| * | | <-----------+ | channel |
| * | | | | |
| * | | Processed | | |
| * | | within the | | |
| * | | driver | | |
| * | | | | |
| * | | | Memory I/O | Peripheral |
| * | | <-------------+ event |
| * | +<------------+ | |
| * +<-----------------------------+ callback | | |
| * | Report peripheral event | | | |
| * | and data for the event | | | |
| * | | | | |
| * | | | SLP_S5 | eSPI host |
| * | | <-------------+ send VWire |
| * | +<------------+ | |
| * +<-----------------------------+ callback | | |
| * | App enables/configures | | | |
| * | discrete regulator | | | |
| * | | | | |
| * | espi_send_vwire_signal | | | |
| * +------------------------------>------------>|------------>| |
| * | | | | |
| * | | | HOST_RST | eSPI host |
| * | | <-------------+ send VWire |
| * | +<------------+ | |
| * +<-----------------------------+ callback | | |
| * | App reset host-related | | | |
| * | data structures | | | |
| * | | | | |
| * | | | C10 | eSPI host |
| * | | +<------------+ send VWire |
| * | <-------------+ | |
| * <------------------------------+ | | |
| * | App executes | | | |
| * + power mgmt policy | | | |
| */ |
| |
| /** |
| * @brief Helper to initialize a struct espi_callback properly. |
| * |
| * @param callback A valid Application's callback structure pointer. |
| * @param handler A valid handler function pointer. |
| * @param evt_type indicates the eSPI event relevant for the handler. |
| * for VWIRE_RECEIVED event the data will indicate the new level asserted |
| */ |
| static inline void espi_init_callback(struct espi_callback *callback, |
| espi_callback_handler_t handler, |
| enum espi_bus_event evt_type) |
| { |
| __ASSERT(callback, "Callback pointer should not be NULL"); |
| __ASSERT(handler, "Callback handler pointer should not be NULL"); |
| |
| callback->handler = handler; |
| callback->evt_type = evt_type; |
| } |
| |
| /** |
| * @brief Add an application callback. |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param callback A valid Application's callback structure pointer. |
| * @return 0 if successful, negative errno code on failure. |
| * |
| * @note Callbacks may be added to the device from within a callback |
| * handler invocation, but whether they are invoked for the current |
| * eSPI event is not specified. |
| * |
| * Note: enables to add as many callback as needed on the same device. |
| */ |
| static inline int espi_add_callback(const struct device *dev, |
| struct espi_callback *callback) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->manage_callback) { |
| return -ENOTSUP; |
| } |
| |
| return api->manage_callback(dev, callback, true); |
| } |
| |
| /** |
| * @brief Remove an application callback. |
| * @param dev Pointer to the device structure for the driver instance. |
| * @param callback A valid application's callback structure pointer. |
| * @return 0 if successful, negative errno code on failure. |
| * |
| * @warning It is explicitly permitted, within a callback handler, to |
| * remove the registration for the callback that is running, i.e. @p |
| * callback. Attempts to remove other registrations on the same |
| * device may result in undefined behavior, including failure to |
| * invoke callbacks that remain registered and unintended invocation |
| * of removed callbacks. |
| * |
| * Note: enables to remove as many callbacks as added through |
| * espi_add_callback(). |
| */ |
| static inline int espi_remove_callback(const struct device *dev, |
| struct espi_callback *callback) |
| { |
| const struct espi_driver_api *api = |
| (const struct espi_driver_api *)dev->api; |
| |
| if (!api->manage_callback) { |
| return -ENOTSUP; |
| } |
| |
| return api->manage_callback(dev, callback, false); |
| } |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| /** |
| * @} |
| */ |
| #include <syscalls/espi.h> |
| #endif /* ZEPHYR_INCLUDE_ESPI_H_ */ |
