| /* |
| * Copyright (c) 2016 Piotr Mienkowski |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /** @file |
| * @brief Definitions for IEEE 802.3, Section 2 MII compatible PHY transceivers |
| */ |
| |
| #ifndef _MII_H_ |
| #define _MII_H_ |
| |
| /* MII management registers */ |
| #define MII_BMCR 0x0 /** Basic Mode Control Register */ |
| #define MII_BMSR 0x1 /** Basic Mode Status Register */ |
| #define MII_PHYID1R 0x2 /** PHY ID 1 Register */ |
| #define MII_PHYID2R 0x3 /** PHY ID 2 Register */ |
| #define MII_ANAR 0x4 /** Auto-Negotiation Advertisement Register */ |
| #define MII_ANLPAR 0x5 /** Auto-Negotiation Link Partner Ability Reg */ |
| #define MII_ANER 0x6 /** Auto-Negotiation Expansion Register */ |
| #define MII_ANNPTR 0x7 /** Auto-Negotiation Next Page Transmit Register */ |
| #define MII_ANLPRNPR 0x8 /** Auto-Negotiation Link Partner Received Next Page Reg */ |
| #define MII_MMD_ACR 0xd /** MMD Access Control Register */ |
| #define MII_MMD_AADR 0xe /** MMD Access Address Data Register */ |
| #define MII_ESTAT 0xf /** Extended Status Register */ |
| |
| /* Basic Mode Control Register (BMCR) bit definitions */ |
| #define MII_BMCR_RESET (1 << 15) /** PHY reset */ |
| #define MII_BMCR_LOOPBACK (1 << 14) /** enable loopback mode */ |
| #define MII_BMCR_SPEED_LSB (1 << 13) /** 10=1000Mbps 01=100Mbps; 00=10Mbps */ |
| #define MII_BMCR_AUTONEG_ENABLE (1 << 12) /** Auto-Negotiation enable */ |
| #define MII_BMCR_POWER_DOWN (1 << 11) /** power down mode */ |
| #define MII_BMCR_ISOLATE (1 << 10) /** isolate electrically PHY from MII */ |
| #define MII_BMCR_AUTONEG_RESTART (1 << 9) /** restart auto-negotiation */ |
| #define MII_BMCR_DUPLEX_MODE (1 << 8) /** full duplex mode */ |
| #define MII_BMCR_SPEED_MSB (1 << 6) /** 10=1000Mbps 01=100Mbps; 00=10Mbps */ |
| #define MII_BMCR_SPEED_MASK (1 << 6 | 1 << 13) /** Link Speed Field */ |
| #define MII_BMCR_SPEED_10 (0 << 6 | 0 << 13) /** select speed 10 Mb/s */ |
| #define MII_BMCR_SPEED_100 (0 << 6 | 1 << 13) /** select speed 100 Mb/s */ |
| #define MII_BMCR_SPEED_1000 (1 << 6 | 0 << 13) /** select speed 1000 Mb/s */ |
| |
| /* Basic Mode Status Register (BMSR) bit definitions */ |
| #define MII_BMSR_100BASE_T4 (1 << 15) /** 100BASE-T4 capable */ |
| #define MII_BMSR_100BASE_X_FULL (1 << 14) /** 100BASE-X full duplex capable */ |
| #define MII_BMSR_100BASE_X_HALF (1 << 13) /** 100BASE-X half duplex capable */ |
| #define MII_BMSR_10_FULL (1 << 12) /** 10 Mb/s full duplex capable */ |
| #define MII_BMSR_10_HALF (1 << 11) /** 10 Mb/s half duplex capable */ |
| #define MII_BMSR_100BASE_T2_FULL (1 << 10) /** 100BASE-T2 full duplex capable */ |
| #define MII_BMSR_100BASE_T2_HALF (1 << 9) /** 100BASE-T2 half duplex capable */ |
| #define MII_BMSR_EXTEND_STATUS (1 << 8) /** extend status information in reg 15 */ |
| #define MII_BMSR_MF_PREAMB_SUPPR (1 << 6) /** PHY accepts management frames with preamble suppressed */ |
| #define MII_BMSR_AUTONEG_COMPLETE (1 << 5) /** Auto-negotiation process completed */ |
| #define MII_BMSR_REMOTE_FAULT (1 << 4) /** remote fault detected */ |
| #define MII_BMSR_AUTONEG_ABILITY (1 << 3) /** PHY is able to perform Auto-Negotiation */ |
| #define MII_BMSR_LINK_STATUS (1 << 2) /** link is up */ |
| #define MII_BMSR_JABBER_DETECT (1 << 1) /** jabber condition detected */ |
| #define MII_BMSR_EXTEND_CAPAB (1 << 0) /** extended register capabilities */ |
| |
| /* Auto-negotiation Advertisement Register (ANAR) bit definitions */ |
| /* Auto-negotiation Link Partner Ability Register (ANLPAR) bit definitions */ |
| #define MII_ADVERTISE_NEXT_PAGE (1 << 15) /** next page */ |
| #define MII_ADVERTISE_LPACK (1 << 14) /** link partner acknowledge response */ |
| #define MII_ADVERTISE_REMOTE_FAULT (1 << 13) /** remote fault */ |
| #define MII_ADVERTISE_ASYM_PAUSE (1 << 11) /** try for asymmetric pause */ |
| #define MII_ADVERTISE_PAUSE (1 << 10) /** try for pause */ |
| #define MII_ADVERTISE_100BASE_T4 (1 << 9) /** try for 100BASE-T4 support */ |
| #define MII_ADVERTISE_100_FULL (1 << 8) /** try for 100BASE-X full duplex support */ |
| #define MII_ADVERTISE_100_HALF (1 << 7) /** try for 100BASE-X support */ |
| #define MII_ADVERTISE_10_FULL (1 << 6) /** try for 10 Mb/s full duplex support */ |
| #define MII_ADVERTISE_10_HALF (1 << 5) /** try for 10 Mb/s half duplex support */ |
| #define MII_ADVERTISE_SEL_MASK (0x1F << 0) /** Selector Field */ |
| #define MII_ADVERTISE_SEL_IEEE_802_3 0x01 |
| |
| #define MII_ADVERTISE_ALL (MII_ADVERTISE_10_HALF | MII_ADVERTISE_10_FULL |\ |
| MII_ADVERTISE_100_HALF | MII_ADVERTISE_100_FULL |\ |
| MII_ADVERTISE_SEL_IEEE_802_3) |
| |
| #endif /* _MII_H_ */ |
