| # Kconfig.bmp280 - BMP280 temperature and pressure sensor configuration options |
| |
| # |
| # Copyright (c) 2016 Intel Corporation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| menuconfig BME280 |
| bool "BME280/BMP280 sensor" |
| depends on SENSOR && I2C |
| default n |
| help |
| Enable driver for BME280 I2C-based temperature and pressure sensor. |
| |
| config BME280_SYS_LOG_LEVEL |
| int "BME280 Log level" |
| depends on SYS_LOG && BME280 |
| default 0 |
| range 0 4 |
| help |
| Sets log level for BMP280 driver. |
| Levels are: |
| |
| - 0 OFF: do not write |
| |
| - 1 ERROR: only write SYS_LOG_ERR |
| |
| - 2 WARNING: write SYS_LOG_WRN in addition to previous level |
| |
| - 3 INFO: write SYS_LOG_INF in addition to previous levels |
| |
| - 4 DEBUG: write SYS_LOG_DBG in addition to previous levels |
| |
| config BME280_DEV_NAME |
| string "BME280 device name" |
| depends on BME280 |
| default "BME280" |
| |
| config BME280_INIT_PRIORITY |
| int |
| depends on BME280 |
| default 70 |
| prompt "Init priority" |
| help |
| Device driver initialization priority. |
| |
| choice |
| prompt "BME280 I2C slave address" |
| default BME280_I2C_ADDR_76 |
| depends on BME280 |
| help |
| Specify the I2C slave address for the BME280. |
| |
| config BME280_I2C_ADDR_76 |
| bool |
| prompt "0x76 (GND)" |
| |
| config BME280_I2C_ADDR_77 |
| bool |
| prompt "0x77 (VCC)" |
| |
| endchoice |
| |
| config BME280_I2C_MASTER_DEV_NAME |
| string "I2C master where BME280 is connected" |
| depends on BME280 |
| default "I2C_0" |
| help |
| Specify the device name of the I2C master device to which BME280 is |
| connected. |
| |
| menu "Attributes" |
| depends on BME280 |
| |
| choice |
| prompt "BME280 temperature oversampling" |
| depends on BME280 |
| default BME280_TEMP_OVER_2X |
| help |
| Select temperature oversampling for the BME280 sensor. Higher values |
| lead to more accurate readings, but higher power consumption. |
| config BME280_TEMP_OVER_1X |
| bool "x1" |
| config BME280_TEMP_OVER_2X |
| bool "x2" |
| config BME280_TEMP_OVER_4X |
| bool "x4" |
| config BME280_TEMP_OVER_8X |
| bool "x8" |
| config BME280_TEMP_OVER_16X |
| bool "x16" |
| endchoice |
| |
| choice |
| prompt "BME280 pressure oversampling" |
| depends on BME280 |
| default BME280_PRESS_OVER_16X |
| help |
| Select pressure oversampling for the BME280 sensor. Higher values |
| lead to more accurate readings, but higher power consumption. |
| config BME280_PRESS_OVER_1X |
| bool "x1" |
| config BME280_PRESS_OVER_2X |
| bool "x2" |
| config BME280_PRESS_OVER_4X |
| bool "x4" |
| config BME280_PRESS_OVER_8X |
| bool "x8" |
| config BME280_PRESS_OVER_16X |
| bool "x16" |
| endchoice |
| |
| choice |
| prompt "BME280 humidity oversampling" |
| depends on BME280 |
| default BME280_HUMIDITY_OVER_16X |
| help |
| Select humidity oversampling for the BME280 sensor. Higher values |
| lead to more accurate readings, but higher power consumption. |
| config BME280_HUMIDITY_OVER_1X |
| bool "x1" |
| config BME280_HUMIDITY_OVER_2X |
| bool "x2" |
| config BME280_HUMIDITY_OVER_4X |
| bool "x4" |
| config BME280_HUMIDITY_OVER_8X |
| bool "x8" |
| config BME280_HUMIDITY_OVER_16X |
| bool "x16" |
| endchoice |
| |
| choice |
| prompt "BME280 standby time" |
| depends on BME280 |
| default BME280_STANDBY_1000MS |
| help |
| Select standby time between measeurements for the BME280 sensor. |
| Higher values lead to lower power consumption. |
| config BME280_STANDBY_05MS |
| bool "0.5ms" |
| config BME280_STANDBY_62MS |
| bool "62.5ms" |
| config BME280_STANDBY_125MS |
| bool "125ms" |
| config BME280_STANDBY_250MS |
| bool "250ms" |
| config BME280_STANDBY_500MS |
| bool "500ms" |
| config BME280_STANDBY_1000MS |
| bool "1000ms" |
| config BME280_STANDBY_2000MS |
| bool "2000ms BMP280 / 10ms BME280" |
| config BME280_STANDBY_4000MS |
| bool "4000ms BMP280 / 20ms BME280" |
| endchoice |
| |
| choice |
| prompt "BME280 filter coefficient" |
| depends on BME280 |
| default BME280_FILTER_4 |
| help |
| Select the filter coefficient for the BME280 sensor. |
| config BME280_FILTER_OFF |
| bool "filter off" |
| config BME280_FILTER_2 |
| bool "2" |
| config BME280_FILTER_4 |
| bool "4" |
| config BME280_FILTER_8 |
| bool "8" |
| config BME280_FILTER_16 |
| bool "16" |
| endchoice |
| |
| endmenu |
